This document provides information on how to perform manual testing based on current R&S TA-TRS QuickStep V4.05 platform in order to adapt to the new released EN 303 345.

14-Apr-2021

This application note demonstrates Rohde & Schwarz test solutions for generating WLAN 802.11ac signals and explains step-by-step how to configure a test signal. Several measurements are presented to illustrate EVM performance.

26-Apr-2013 | AN-No. 1GP94

Generating and Analyzing CDMA2000 Signals

27-Mar-2001 | AN-No. 1MA34

Seamless Level Setting on the R&S SFU

23-Jun-2006 | AN-No. 7BM54

In this application note we explain how to test FPGA-based hardware emulators using Rohde & Schwarz vector signal generators for creating suitable real-time test signals at reduced sample rates. We further explain how to correctly adapt AWGN signal generation and fading simulation for “slow I/Q”.

10-Dec-2012 | AN-No. 1GP95

In addition to the generic edge trigger, modern oscilloscopes offer triggers that are specialized to address specific problems.

04-Jan-2016

Measuring Bit Error Rate using the R&S SFU-K60 Option

19-Dec-2006 | AN-No. 7BM51

Demonstration of BER Test with AMIQ controlled by WinIQSim

29-Sep-1998 | AN-No. 1MA16

LTE user equipment (UE) receiver performance has significant impact to cellular radio network coverage and capacity. It determines the maximum data throughput across the air interface between the LTE base station (eNB, evolved node B) and the mobile network subscriber UE, thus it determines the total capacity across the air interface. Therefore, it is one of the most important measurements to verify the actual receiver performance of individual devices, and a key metric to compare different devices, in particular.This paper shall give an introduction to receiver performance measurements and discusses the measurement metrics as well as the challenges of over the air (OTA) measurements.

31-Aug-2017 | AN-No. 1ST001

Transfer of Trace Data from R&S Network Analyzer ZVx to Microsoft Excel

22-Mar-2007 | AN-No. RSI02

Power converters with a full-bridge topology are frequently used in telecommunications and servers that need to be compact, efficient and cost sensitive, making them more complex. Switching patterns for all the main primary switches including synchronous rectifier switches need to be validated after the first protype is built. This complex validation requires proper measurement of switching patterns to prevent catastrophic switching patterns. Expertise and the right measurement tools are essential when identifying unexpected events in the converter switching process.

17-Jan-2024

he option R&S EMC32-K84 extends the internal report generator to support the generation of a summary test report over all selected test cases done for a DUT.

23-Apr-2015 | AN-No. 1SP09

This document describes Bluetooth Low Energy RF over-the-air RX and TX measurements using advertising channels for communication with Bluetooth Low Energy devices.

14-Dec-2020 | AN-No. 1C109

Vector Network Analyzers of t ZNA and ZNB family are able to measure magnitude and phase of complex S-parameters of a device under test (DUT) in the frequency domain.

30-Jul-2020 | AN-No. 1EP83

Primer

selection of appropriate RF power sensor

26-May-2021

How to implement GTSL outside a test stand environment

02-Jul-2002 | AN-No. 1SC01

Get deep insight into your design with a dual-path, precisely synchronized source driving the Doherty amplifier and improve your yield.

12-Jul-2018

Verification of wideband power amplifiers

19-May-2020

The R&S®NGL200 and R&S®NGM200 can simulate battery cells when testing battery management systems and replace far more expensive dedicated battery simulators.

08-Jun-2020

Using the Frequency Conversion Mode of the ZVR Vector Network Analyzer

19-Jan-1999 | AN-No. 1EZ47

Read this application card to learn more about what the 10BASE-T1S Ethernet compliance test offers and how it ensures reliable operation and functionality.

15-May-2020

The R&S®RT-ZPR20 and R&S®RT-ZPR40 power rail probes with a 1:1 attenuation ratio have very little noise and sufficient bandwidth to not attenuate critical signal content.

17-Jul-2018

High dynamic range current measurements on IoT devices

01-Oct-2019

eCall is deployed in Europe and is required by law in new cars as of March 2018. Next generation eCall (NG eCall) is built on LTE and 5G.

06-Jun-2018

Generation of Test Signals acc. ISO 14708 for Testing of Cardiac Pacemakers

15-Jul-2009 | AN-No. RCS0812-0065

HSDPA - Challenges for UE Power Amplifier Design

11-Jul-2011 | AN-No. 1MA84

Testing HSPA+

26-Apr-2013 | AN-No. 1MA121

Rohde & Schwarz makes the simulation of complex coexistence scenarios simpler than ever before, thanks to a quick and easy setup of complex interference scenarios.

18-Mar-2019

This application note describes Methods of Implementation (MOI) for precise, fast, and error-free compliance testing of USB Type-C to Type-C cable assemblies supporting USB4 Gen3, USB4 Gen2, USB 3.2 Gen2, USB3.2 Gen1, and USB2.0.

30-Nov-2023 | AN-No. 1SL405

This application note is a systematic guide to help test engineers configure the Vector Network Analyzer in order to perform compliance test on Automotive Ethernet cables according to the Open Alliance TC9 standard.

13-Aug-2019 | AN-No. GFM323