10 Results
Calibration and Verification Solution
The UWB (Ultra-Wideband) technology is a short range wide-band radio technology specified for device to device communication operating in unlicensed spectrum. It is an RF positioning technology that enables accurate and secure peer-to-peer ranging between mobile devices with robust resistance to interference while consuming very low energy and coexisting well with other radio communication systems. UWB is used for a variety of different applications, such as asset tracking, secure payment, personal tracker, real time location services and keyless access and start of a vehicle etc. According to ABI Research forecasts, there will be well over 1 billion UWB annual device shipments by 2026. Almost every smart phone shipped in 2026 will support UWB services.Talking about testing aspect of a UWB device, in general two test methodologies can be adopted as other wireless products, either the traditional testing mode (so-called conducted test mode) with wired RF connection between the test measurement equipment and device under test (DUT) or over the air (OTA) test mode in an OTA anechoic chamber. Sometimes, it is not always possible or necessary to perform the tests under conducted mode due to the limiting factors, e.g. cost, space, complexity and direct access to the RF connectors of the product. In this case, OTA testing is then becoming a non-evitable approach. Moreover, OTA testing reflects the usage of DUT in a real condition.In this application note, R&S® OTA test solution covering transmitter (Tx), receiver (Rx) and Time of Flight (ToF) testing in Wireless Automated Testing (WMT) environment is described. The measurement results throughout the whole document are based on NXP Trimension™ NCJ29D5 UWB automotive IC.
12-Apr-2023 | AN-No. 1SL394
Rohde & Schwarz signal generators can generate standard-compliant WLAN IEEE 802.11ax signals for high efficiency (HE) receiver testing.This application note helps to choose the right generator test solutions and explains step-by-step how to generate 802.11ax SISO and MIMO signals. Measurements, such as EVM, are presented to illustrate the signal performance. Furthermore, this document shows how to test 802.11ax receiver specifications and the newly introduced HE trigger-based PPDU specifications according to the IEEE P802.11ax/D1.3 specification draft.
16-Aug-2017 | AN-No. 1GP115
The Internet of Things (IoT) is considered the driving force of current and future wireless communications. In release 13, 3GPP has specified Narrowband-IoT (NB-IoT) as a new physical layer. This application note gives a short introduction to NB-IoT and shows the easy measurements with Rohde & Schwarz instruments.
30-Jun-2017 | AN-No. 1MA296
Distortions caused by components in the RFFE (radio frequency front end) limit the performance and throughput of communications systems. Types of distortions include:▪ AM-AM and AM-PM (complex variations of gain with amplitude)▪ Non-linear frequency response (memory effect)All RFFE components exhibit all of these distortions, only the proportions vary. In this Application Note, illustrative measurements of individual RFFE components, as well as a complete RFFE, will be made. This is followed by the documentation of a more complete analysis, including comparison against theoretical limits, of a linearized commercial SatCom BUC product.
27-Feb-2017 | AN-No. 1MA299
The Doherty Amplifier continues to be rolled out in an increasing number of TxFE (Transmit Frontend) applications, as the quasi-linear amplifier architecture of choice.The advent of 5G, with its inevitable microwave or millimeter wave air interface, increase the design challenges associated with its construction; not least of all because of the potential for increased dispersion in the constituent amplifiers and combiners.This application note describes a measurement-based development methodology by which the Doherty Amplifier may be enhanced, increasing performance and/or performance bandwidth. This methodology is supported with a working example.The methodology may also be extended to balanced, spatially combined and anti-phase (so called "pushpull" or "differential") amplifiers, the latter often itself nested in Doherty configurations.The R&S®Quickstep sequencing software may be downloaded from:
26-Sep-2016 | AN-No. 1MA279
More and more mobile radio networks implement remote radio equipment (RE) that is connected to the base station main unit via a digital interface using standardized transmission protocols such as CPRI. For testing RE devices Rohde & Schwarz offers a complete test solution based on the R&S®EX-IQ-BOX [Model K04]. This key component is a configurable digital interface module that is used to connect Rohde & Schwarz test equipment to a RE under test using CPRI data transmission. This application note explains in detail the instrument setup and configuration needed to successfully test your remote radio head.
05-Aug-2013 | AN-No. 1GP78
This application note helps the user to configure a Rohde & Schwarz vector signal generator for LTE FDD repeater conformance testing. It explains step by step how to set up the baseband signal for the various test cases defined in the 3GPP Technical Specification 36.143.The R&S®SMx vector signal generators provide predefined, LTE-conform test models and are therefore ideal for LTE repeater conformance testing. The test cases in TS 36.143 can be set up with a single instrument which provides all necessary test signals including the four specified repeater stimulus signals.
26-Apr-2013 | AN-No. 1GP85
Rohde & Schwarz signal generators can generate standard-compliant WLAN IEEE 802.11ac signals up to 160 MHz bandwidth with excellent EVM performance. This application note demonstrates the generator test solutions and explains step-by-step how to configure a test signal. Several measurements are presented to illustrate EVM performance.
26-Apr-2013 | AN-No. 1GP94
This application note describes how to connect R&S® test and measurement products quickly and seamlessly to AWR® Visual System Simulator™ (VSS) via a GPIB or LAN interface. Using AWR® Connected™ customized for Rohde & Schwarz hardware and R&S® WinIQSIM2™ signal simulation software, the flexibility of digital radio standards is highlighted and its integration into VSS is demonstrated.
20-May-2010 | AN-No. 1MA174
DVB-T Bursted Noise is a tool for generation of DVB-T compatible noise signals. The IQ data can tranferred to WinIQSIM™ / WinIQSIM2™ for further processing and transmission to an AMU, AFQ, AMIQ, SMU, SMIQ.
08-Jul-2009 | AN-No. 1MA51