Verification of baseband data is an important step in the early development phase of LTE/LTE-A-ready products. Comparison values for baseband data (test vectors) from other sources can be very useful in order to verify the correct implementation of the standard. Option K81 for the R&S®SMx200A vector signal generator offers sample data for LTE at the bit level. The reference data enables users to test their own implementation of the specification. The LTE bit stream verification program shown here uses data generated by this option and offers a (bitwise) comparison with bit streams generated for an LTE downlink signal. Therefore it demonstrates, how easy the option R&S SMx-K81 can be integrated into the simulation and design process during the development of LTE/LTE-A handsets or base stations.

02-Feb-2011 | AN-No. 1MA161

PESQ measurements employ a level adaptation algorithm and are hence widely insensitive to absolute level. However, if the tests are performed via a speech codec, the driving level of the codec has an influence on the MOS result. Therefore careful alignment of the level is required. This application note provides an application program which runs on the Audio Analyzer R&S UPV or R&S UPV66 and can be used to calibrate signal levels for the PESQ measurement.

30-Jun-2011 | AN-No. 1GA50

This application note demonstrates the use of the Measurement Receiver to calibrate the signal output level of a Signal Generator.Calibration in this application is a two-step process.► The absolute output level of the signal source, at a fixed level, is measured using a thermal power sensor (e.g. NRP50T), which in turn outputs its reading to the FSMR.► Output power calibration over a wider dynamic range (to lower power) is performed by connecting the FSMR to the signal source directly, and sweeping the power of the signal source.The FSMR offers a nominal total measurement uncertainty of <0.015 dB +/- 0.005 dB per 10dB step. At 1GHz, the power measurement range covers -152 dBm to +30 dBm. It is this intrinsic linearity, that the accuracy of the calibration relies upon.Absolute power measurement uncertainty, for the NRP50T thermal power sensor used in this Application Note, is 0.040 dB to 0.143 dB.This process may be repeated at multiple frequencies. Calibration values are automatically stored and managed by the FSMR. Measurement frequencies for calibrations are stored, will be automatically recalled by the FSMR, by re-selection of those frequencies.

31-Dec-2021 | AN-No. 1SL377

This application note shows how to run 3GPP WCDMA BER and BLER tests according to standard TS 25.141 with the Vector Signal Generators R&S®SMBV100A, R&S®SMJ100A, or R&S®SMU200A. The description of hardware test setup is followed by detailed instructions on how to configure the R&S® generators and how to run a BER or BLER test step by step. Remote control commands for the generators are included, to simplify integrating the BER/BLER tests into your proprietary test suite.

06-Mar-2009 | AN-No. 1MA144

Make more accurate power rail measurements.

09-Jul-2020

The 3GPP TS 36.521-1 “Radio transmission and reception” LTE User Equipment (UE) conformance specification defines the measurement procedures for LTE terminals with regard to their transmitting characteristics, receiving characteristics and performance requirements as part of the 3G Long Term Evolution (3G LTE) standard.This application note describes how to use the LTE Frequency Division Duplex (FDD) and Time Division Duplex (TDD) measurement functionality associated with the Downlink Carrier Aggregation feature of the R&S®CMW500 wideband radio communication tester to perform LTE R10 receiver measurements according to this test specification.

09-Apr-2015 | AN-No. 1CM103

Rohde & Schwarz signal generators and spectrum analyzers can be used to test IEEE 802.11ax stations in terms of uplink accuracy requirements. Measurements such as residual carrier frequency error and timing accuracy of HE TB PPDU transmissions are supported.

09-Nov-2017

Automotive Infotainment Testing

24-Apr-2018

Battery life time is usually one of the most important specifications for battery-powered devices. Depending on the application, life time requirements can range from tens of hours for typical wearables like smart watches to ten years for smart sensors. Understanding where and when energy is used in order to minimize power consumption is therefore key for any of these devices.The power consumption analysis tool was developed to make it easier for customers to analyze power consumption data collected with either the NGL, NGM or NGU power supplies from Rohde & Schwarz. It allows to easily capture power consumption data and analyze using basic measurements.

31-Jan-2022 | AN-No. 1SL380

The R&S®ZNB vector network analyzer is easy to configure and calibrate using the built-in intermodulation wizard.

19-Dec-2013

Sequencer Software Tool

14-Mar-2016

Today’s electronic devices often draw non-sinusoidal, irregular current where harmonic current is fed back into the universal supply system. Monitoring this current is both crucial and mandatory for CE compliant devices. The R&S®NPA701 compliance tester seamlessly and efficiently monitors this current.

28-Mar-2024

Vector Network Analyzers of the ZVR family measure magnitude and phase of complex S-parameters of a device under test (DUT) in the frequency domain. Using an inverse Fourier transform, the results can be transformed to the time domain. The impulse or step response of the DUT is obtained, which gives an especially clear representation of its characteristics. For instance, faults in cables can be directly localized. Moreover, special time domain filters, so-called gates, can be used to suppress unwanted signal components such as multireflections.

04-Aug-1998 | AN-No. 1EZ44

The new IP connection security analysis solution for the R&S®CMW500 platform identifies IoT and mobile communications devices’ IP connection vulnerabilities in an early stage of development.

04-Apr-2017

This application notes describes remote operation or monitoring of the spectrum analyzers R&S® FSL3, R&S® FSL6, R&S® FSL18 through a standard web browser. The common cross-platform technology Virtual Network Computing (VNC) is used as a server on the instrument.

07-Jan-2009 | AN-No. 1EF66

Reflection measurements are a common way of assessing antenna system performance. When a minimum amount of the transmitted signal is reflected, it indicates that the transmission energy can reach the intended coverage. Undesired high reflection causes the system to be inefficient and can damage components. Reflection measurements can be expressed in terms of return loss, VSWR and reflection coefficient.

13-Nov-2017

In this document we will describe in detail how to configure and perform path calibrations with AMS32-K81 in an ATS1500C, using an AREG800A.

03-May-2023 | AN-No. 1SL399

Noise Power Ratio Signal Generation and Measurement

Noise Power Ratio (NPR) is an add-on tool for WinIQSIM™ to generate noise power ratio stimulus signals and measure the resulting noise power ratio of a device under test (DUT) using Rohde & Schwarz instruments via LAN or GPIB bus.

06-Nov-2015 | AN-No. 1MA29

Many serial interfaces use Manchester or non-return-to-zero (NRZ) coding. Oscilloscopes typically offer dedicated software options for debugging and testing the communications interfaces for common standards such as I2C, UART or CAN. The R&S®RTx-K50 option expands the addressable range of interface standards by adding decoding capability for standardized and proprietary Manchester or NRZ coded buses. It allows customizable configuration of the protocol structure that has to be decoded.

19-Oct-2020

R&S®NESTOR cellular network analysis software supports law enforcement agencies (LEA) in forensics activities and crime scene investigations (CSI) by gathering information through analysis of surrounding mobile networks. R&S®NESTOR increases public safety by reducing crime scene investigation time by up to 50 %.

14-Mar-2024

The R&S®SK4105 HF high-power transmitter is ideal for air traffic service under harsh conditions such as those in Greenland

17-May-2023

With its small footprint, the R&S®ATS1000 antenna test system is the ideal direct far-field OTA system to test phased array antennas. The system tests and optimizes the radiation characteristics of any modules using the AiP technology from 18 GHz to 87 GHz.

12-Mar-2020

Sequencer Software Tool

20-Feb-2015

R&S®CMWcards is an intuitive and user-friendly software application that makes mobility verification easier than ever.

23-Jul-2019

Being faced with a wide variety of standards and manufacturer’s specifications, test engineers may often find it difficult to keep track of necessary audio measurements. This is aggravated by the fact that modern audio analyzers offer a multitude of settings. This application note serves as an aid offering a collection of typical setups that make it possible to get started with measurements immediately. In addition, information is given on associated standards, on the adaptation of the setups to specific measurement tasks as well as on the evaluation of results.

04-Jun-1998 | AN-No. 1GA36

Combining the R&S®UPP audio analyzers with the R&S®SMB100A signal generators provides the most compact and fastest test solution for modern FM car radios

19-Feb-2015

This application note explains the fundamentals of the cell search and cell selection and reselection procedures required for both modes of UMTS Long Term Evolution: FDD and TDD. It describes how to generate and analyze the required signals using Rohde & Schwarz test and measurement solutions. The application note also shows how to perform interoperability tests and terminal conformance tests according to the baseline of the 3GPP specifications for protocol conformance and Radio Resource Management (RRM).

17-Sep-2009 | AN-No. 1MA150

This application note is one of three papers dealing with the WiMAX standard, covering the theoretical aspects of WiMAX. It gives a detailed overview of the basic concepts of WiMAX (FFT, OFDM, frame structures, etc) and explains the physical standard parts of IEEE 802.16 standards 802.16-2004, corr1 and 802.16e.Please see also 1MA97 for Generating and analyzing 802.16-2004 and 802.16e-2005 signals and 1EF57 for an introduction to the WiMAX standard.

13-Jun-2006 | AN-No. 1MA96

Protecting the public: the ARDRONIS counter drone solution from Rohde & Schwarz prevents drone related security threats at major events.

18-Dec-2024

Radio frequencies in bands around 28 GHz are being discussed as candidates for mobile communications of the fifth generation (5G). Beam steering will be a key feature in the context of 5G. It will be a major challenge to test the beam steering capabilities of base stations and user equipment in every phase from research and development through production. Conducted measurements will be mainly replaced by over-the-air measurements of electromagnetic radiation. Rohde & Schwarz offers the R&S®NRPM Over-the-Air (OTA) Power Measurement Solution that perfectly fits such measurement needs.Part of this solution are the R&S®NRPM-A66 antenna modules. They have integrated diode detectors. Thus, there are no cables between the antenna and the detector as in traditional setups. This avoids high and potentially unknown RF losses. The R&S®NRPM-A66 antenna modules with their integrated diode detectors are factory calibrated, which means that the user does not have to calibrate them to achieve highly accurate measurement results.This application note contains theoretical background on OTA power and pattern measurements. It gives step-by-step instructions for the verification of the power level and the radiation pattern of a device under test (DUT) in comparison to a golden device, and it presents an approach for verifying the accuracy of beam steering.

29-Aug-2017 | AN-No. 1GP118