Sequencer Software Tool

14-Mar-2016

Today’s digital designs and high-speed data converters require clean clocks with minimal jitter

03-Aug-2017

Deep memory in an oscilloscope ensures that long waveforms are captured with high resolution right down to the details thanks to a high sustained sample rate. Users can be confident that they are not ‘missing anything’. They benefit from viewing longer periods of time and quickly finding signal anomalies or important events.

21-Mar-2017

Rohde & Schwarz mobile network testing solutions enable operators to efficiently increase network capacity via hardware-related, capacity-enhancing features such as antenna tilt optimization, carrier aggregation, 4x4 MIMO and 6-sector sites.

09-Aug-2016

SMIQ/ABFS TV shows the SMIQ or ABFS display remotely on any Windows™ PC

02-May-2002 | AN-No. 1GP54

The R&S®TSStream multi-TS streaming software streams a number of MPEG transport stream files simultaneously over a single IP interface. The individual transport streams result in a high overall bit rate. To make the streams available on a standard PC, the R&S®TSStream software does not play the transport stream files directly from the hard disk but first loads them into the RAM. The maximum number and length of the transport streams depends solely on the PC's available RAM.

16-Mar-2017 | AN-No. 1GP113

This paper describes the measurement of additive/residual phase noise of power amplifiers or multipliers for example for automotive RADAR sensors at 80 GHz using the interferometric measurement approach in combination with a phase noise and VCO tester R&S FSWP. The setup provides a way to characterize the additive/residual phase noise of amplifiers down to -150 dBc/Hz at 100 kHz offset even in the microwave range at 80 GHz.

11-Sep-2024 | AN-No. 1EF117

The I/Q-Modulation Generator AMIQ provides high precision I/Q analog output for data calculated by the software WinIQSIM. Additionally, the software AMIQ-K2 enables you to read, convert, and transfer existing data files from various other programs to AMIQ format. Input formats supported by AMIQ-K2 are: - The propriety R&S programs IQSIM and DAB-K1. - Mathematic calculation programs like Matlab and Mathcad. - AWG202, COSSAP and ADS data files. AMIQ-K2 also provides you with remote control for AMIQ. For hardware and software requirements see section 2. AMIQ-K2 transfers data to AMIQ using either - GPIB - RS232. An extensive manual is supplied to help you use AMIQ-K2.

24-Nov-1999 | AN-No. 1MA10

The R&S WiMAX application firmware R&S FSx-K93 calculates several different power parameters. This application note describes the basic power measurements of WiMAX OFDMA signals and gives an overview of the calculation of the different values.

11-Jul-2007 | AN-No. 1EF60

This application note describes the general setup and required equipment for EMC measurements according to the EMS standard IEC / EN 61000-4-6.

29-Mar-2007 | AN-No. 1SP31

FMCW radar sensors are used in vehicles for adaptive cruise control and for blind-spot, lane-change and cross traffic assistants. Radar sensors for acquisition of the surroundings are key components for future vehicles with semi-autonomous and fully autonomous driving. Autonomous driving requires radars that reliably detect objects in the surrounding area. Radar makes it possible to quickly and precisely measure the radial velocity, range and azimuth and elevation angle of multiple objects. For this reason, the automobile industry is increasingly using this technology in advanced driver assistance systems (ADAS). Rohde & Schwarz offers T&M solutions for generating, measuring and analyzing radar signals and components to ensure trouble free operation of these sensors. The high-performance oscilloscope R&S® RTP with four measurement channels is the perfect solution for multi-channel measurements on MIMO radar sensors and correlation with other signals e.g. power rails, whereas a spectrum analyzer such as the R&S® FSW85 offers highest dynamic up to 85 GHz.This application note focuses on how to measure and analyze FMCW radar signals with up to 6 GHz bandwidth with an R&S® RTP oscilloscope. On-board analysis features for pulse and chirp analysis for single- and multi-channel measurements will be addressed as well as the combination of oscilloscope and R&S® VSE software. Measurement of an FMCW radar signal in the 77 - 81GHz band with 4 GHz bandwidth is demonstrated.

07-Aug-2019 | AN-No. GFM318

This application note provides information about the spurious emission measurement on 3 GPP base station transmitters. The basic requirements and the limiting factors of a spectrum analyzer are explained in detail. Dynamic range calculations with measurement examples show the practical realisation of spurious emission measurements.

10-Jan-2002 | AN-No. 1EF45

Unique automatic level controlled (ALC) based test setup using the R&S®ZVA vector network analyzer and R&S®BBA150 broadband amplifiers provides highly accurate and reproducible results in minimum test time.

27-Sep-2013

A high frequency transformer is a key component when designing isolated switching mode power supplies (SMPS). Leakage inductance is essential in the control of many design parameters including efficiency, maximum voltage rating for switching elements and EMI when it comes to designs using customized transformers. Accurate measurement of this parasitic element is mandatory. The R&S®LCX LCR meter is ideal for this challenging measurement task.

15-Feb-2022

This application note describes ho to test and perform measurements on AMPS phones both using the remote-control program CMUgo and manually at the CMU200.

07-Sep-2004 | AN-No. 1CM53

This appication note introduces a program suitable for generating and analyzing WiMAX IEEE 802.16 signals for power amplifier testing. The program allows the user to change the generator settings, to select specific pre-defined test parameters and to analyze the test results. The application note describes the test parameters and the features and capabilities of the program.

03-Aug-2007 | AN-No. RAC-0611-0025

The R&S CMU300 combines high-precision Node B parameter tests with layer 1 signalling processes for the first time. Thus, you can now test Node Bs under more realistic conditions as it was possible with existing concepts. This document describes the new measurement functions and provides an overview of their applications.

10-Nov-2005 | AN-No. 1CM58

This document is divided in two parts and starts with an introduction in AC-DC conversion principles in general. It will present the most common circuits used for different power levels. The switching mode power supply (SMPS) converter will be the main focus as they are used everywhere in the electronics. Especially the flyback converter design in different flavors are highlighted. Nevertheless, all measurements are also applicable for other SMPS converter designs operating at higher power levels.In the second part of this document, most relevant testing methods and procedures of an AC-DC converter are highlighted. For each testing section, a fundamental part will be upfront discussed and it is followed by a presentation of a suitable measurement method. In this second part, the device under test (DUT) is considered as black box device and thus the structure is similar. Therefore, the testing parts consists of methods related to input tests, output tests and a combination of both like efficiency. Of course, some test performed at the output of the converter are also relevant for DC-DC converter, e.g. the validation of the output ripple.

14-Nov-2022 | AN-No. 1SL387

An offline AC/DC switching converter has no separate bias power supply that provides power to the control integrated circuit itself. Here, an auxiliary primary winding and discrete components are added to supply power to the control circuit. Verifying this circuitry is essential and requires accurate and detailed signal level and timing measurements. The startup sequence takes a long time, which needs to be taken into consideration in the measurement and requires an instrument with sufficient memory.

23-Nov-2022

Mobile network operators worldwide face cost pressures and escalating network complexity. The advent of 5G-NR has ushered in new use cases and flexibility, but it also comes with more stringent performance and availability requirements.Machine Learning can serve as a catalyst for the market to unearth deep insights that would otherwise remain concealed. It can also significantly streamline everyday tasks by fostering a smarter system that guides users through their routine work processes, rather than obliging them to repeat each (manual) step. Rohde & Schwarz Mobile Network Testing has focused its efforts on delivering Machine Learning use cases that distill relevant insights from drive testing data, thereby offering substantial benefits to users.This educational note explains the motivation and reasoning why this kind of approach is needed, what are the benefits of the machine learning offering and it takes a deeper look into how it can be used in various levels of statistical and technical analysis. Finally, this document provides real measurement results and analysis findings based on the Rohde & Schwarz post processing SW suite SmartAnalytics and its machine learning based features Call Stability Score and Network Utilization Rating.

28-Feb-2024 | AN-No. 8NT10

Oscilloscopes are basic everyday instruments for engineers and electricians. Maintenance tasks, however, sometimes require very specific measurements that are not available as standard functionality or are difficult to set up manually. With the R&S®RTH-K38 user scripting option, engineers can now design their own measurement function and a simple user interface. This paper describes how to use this unique feature for railway maintenance work.

06-May-2020

The RSIB interface enables the network analyzers of the ZVR family to be controlled by means of Windows applications via DDE. The interface functions are contained in the DLL RSIB.DLL. The other DLL RSDDE.DLL provides functions for the DDE access to the instrument firmware. These functions are used by RSIB.DLL. The interface of these functions greatly corresponds to that of National Instruments for programming the GPIB. The function names are similar to those of the NI library but preceded by RSDLL. The two DLLs are part of the firmware and are updated with the firmware update kits.

31-Jul-1998 | AN-No. 1EZ33

The Society of Cable Telecommunications Engineers (SCTE) defined the ANSI/SCTE 40 specification: Digital Cable Network Interface Standard. ANSI/SCTE 40 tests are designed to test conformance of set-top boxes and other cable receiving equipment to ensure that they will operate correctly when installed in a cable system. The tests are a combination of noise (AWGN and phase noise), AM hum, micro-reflections, digital and analog adjacent channels, and other discrete interferences. These impairments are found on most cable systems to some degree. Rohde & Schwarz provides set-top box manufacturers with an easy solution to perform conformance testing in line with ANSI/SCTE 40 by using the R&S®SFU broadcast test system and the R&S®SFE100 broadcast tester. The R&S®SFU is able to perform most of the test procedures in one unit. Furthermore, additional test transmitters allow the simulation of full channel loading. This Application Note explains the specific test requirements, a possible setup, and the configuration using the R&S®SFU/SFE100.

29-Oct-2009 | AN-No. 7BM68

Leaving aside the microwave generators, the present line of Rohde & Schwarz products comprisessignal generators up to 1 GHz (SMX, SMG), up to 2 GHz (SMH, SMGU), up to 3 GHz (SME, SMT) and up to 4.3 GHz (SMHU). For applications at higher frequencies, all signal generators can also be operated with an external passive frequency doubler. This extends the range of possible applications up to 8.6 GHz. Some degraded specs regarding level and modulation are described below. For people using the frequency range 3 to 6 GHz, the low priced combination SMT plus frequency doubler will mainly be interesting. Signal generator SMHU is useful for the frequency range up to 8.6 GHz. Especially the phase noise performance is excellent with this instrument. the required output signal. It should also be pointed out that the residual FM and the SSB phase noise will be 6 dB poorer as a result of frequency doubling.

20-Apr-1998 | AN-No. 1GPAN03

IEEE 802.15.4 (ZigBee™) uses OQPSK with a half-sine pulse shaping filter as modulation. This application note describes how to generate and analyze ZigBee™ signals. Simple test signals can be setup with the free-of-charge simulation software R&S WinIQSIM™ and transferred to the vector signal generator R&S SMU200A. It describes how to setup the vector signal analyzer R&S FSQ with option R&S FSQ-K70 for ZigBee™ signal demodulation and how to analyze modulation quality such as error vector magnitude (EVM).

21-Jun-2007 | AN-No. RSI03

The R&S®Pulse Sequencer software together with the R&S®SMW200A vector signal generator offers a simple and easy way to simulate multi-emitter environments. It enables engineers to validate and verify the EW receiver performance.

13-Nov-2018

Short measurement time in conjunction with high accuracy and repeatability of results are essential for efficient testing of mobile phone power amplifiers. Power Meter R&S®NRP, Signal Generator R&S®SMIQ, Spectrum Analyzers R&S®FSP/FSU/FSQ and Power Supply R&S®NGMO2 offer optimum characteristics such as high accuracy, fast settling speed and short measurement time in programmed mode. This application note concentrates on testing GSM/EDGE mobile power amplifiers and shows typical test setups and programming examples for Signal Generator R&S®SMIQ and Spectrum Analyzer R&S®FSP/FSU/FSQ, benchmark numbers and repeatability results.

29-Apr-2004 | AN-No. 1MA66

The use of Rohde & Schwarz device drivers under VEE software is not complicated. However, a number of factors are involved, the errors that occur are often difficult to diagnose. This application provides easy and detailed support for installation and troubleshooting using National Instruments or Agilent GPIB boards.

20-Dec-2012 | AN-No. 1MA035

The topic of this application note is mobile phone measurements – in theory and in practice. It discusses measurements according to the most common standard in use today, GSM.The first, theoretical portion of this application note covers digital modulation and access methods in general. This is followed by an overview of the specific characteristics of the GSM standard as well as a summary of the most important mobile radio measurements.The second, practical portion of this application note covers some of these measurements in detail and runs through them step by step. These measurements can be performed by small groups in labs.The measurements and analysis of the results are intended to illustrate the theoretical portion of the application note and to deepen the reader's understanding.All measurements are performed using the R&S®CMW500 wideband radio communication tester and an off the shelf mobile phone.

22-Aug-2014 | AN-No. 1MA231

The Rohde & Schwarz R&S CMU200 can be configured to perform packet data testing in a Mobile IP or Simple IP environment.This application note is intended as a guide to configuring the necessary Mobile IP or Simple IP network elements and R&S CMU200 instrument.

25-Apr-2007 | AN-No. 1CM51