EMI debugging, FPC, FPC1000, FPC1500, EMC compliance test, EUT The combination of high power and current being sharply switched on and off has a lot of potential for EMI. EMI debugging a switched-mode power supply with R&S®FPC1000/ R&S®FPC1500 EMI debugging, FPC, FPC1000, FPC1500, EMC compliance test, EUT The combination of high power and current being sharply switched on and off has a lot of potential

30-Jun-2019

FSxRecordPlay is a program for recording the trace data in frequency and time domain from Rohde & Schwarz spectrum analyzers and measurement receivers via IEEE bus, LAN/Internet or internal remote control connection. The stream waveform data can be played back and analyzed directly in this software with variable speed.

20-May-2010 | AN-No. RAC-0605-0004

radio signals, automatic monitoring, interference, RF radiation, frequency spectrum, Automatic monitoring of radio signals interfering with sensitive devices in hospitals Automatic monitoring of radio signals interfering with sensitive devices in hospitals radio signals, automatic monitoring, interference, RF radiation, frequency spectrum, Automatic monitoring of radio signals interfering with sensitive

04-Sep-2006

The sweep tool has several R&S®NGU source measure unit functions for characterizing semiconductors.

02-May-2023

Electronic systems like electronic control units (ECU) must pass several stringent qualification tests in order to be approved for automotive use. These tests include a reverse polarity test which is specified as part of ISO 16750‑2. In line with the specification, the electronic module must withstand a negative supply voltage for a specific time without suffering any damage. The R&S®NGU401 source measurement unit (SMU) is ideal to perform this task, plus it provides automated testing capability.

23-May-2022

Rohde & Schwarz has made a breakthrough for better jitter and noise separation with the launch of SW options (RT-K133 & RT-K134). Technical information on this new algorithm were presented at . We received a lot of positive feedback on this new technique. However, one fundamental question still remained. How does this new algorithm compare to established solutions available on the market today?This app note provides an introduction into the various jitter components and elucidates the commonly available jitter separation frameworks. Finally, it provides a comparison between the different commercial solutions, while explaining the used waveforms and signals to achieve the results. Curios? Read on, to learn how Rohde & Schwarz’s new option for jitter and noise separation delivers dependable and stable results. If you are interested in evaluating on your own, you may download the waveform files with registration.

08-Dec-2021 | AN-No. 1SL375

Modern mobile phones can support cellular and noncellular wireless communications standards at the same time. This means, however, that the subsystems must operate in very close proximity to each other within a single device (in-device coexistence). The resulting high level of reciprocal leakage can at times cause considerable interference.This application note employs preliminary theoretical analysis and demonstrates how the problems of indevice coexistence can be measured. For german version please visit .

28-Apr-2015 | AN-No. 1MA255

This application note shows all necessary settings for measuring shielding effectiveness using the R&S®EMC32-K48 option via R&S®EMC32 Measurement Software.

01-Dec-2015 | AN-No. 1SP19

Signal monitoring has proven an effective technique when it comes to identifying and correcting quality problems in transmitted TV broadcast signals during broadcast operation. For a DVB‑T2 signal using multiple physical layer pipes (multi-PLP), a separate receiver is required to analyze each PLP. The R&S®DVMS digital TV monitoring systems are extremely flexible and can be configured to meet customer's needs – from sequential PLP monitoring systems with a single receiver to systems providing seamless, parallel multi-PLP analysis.

24-Jul-2012

This application note shows how to remote control the switching of RF and digital I/O signals by R&S®OSP Open Switch and Control Platform directly from a Vector Network Analyzer (VNA) or from a Spectrum Analyzer (SA). The R&S®ZVA, R&S®ZVB, R&S®ZNB, R&S®FSW and R&S®FSV families are covered. The application note first describes the requirements and setup procedure. It is shown how to install the software and how to set up the system in order to get highest flexibility and best usability. It is then shown how to calibrate the entire configuration and finally some practical examples are provided. Switching is explained using VNAs as an example, the appendix 5.4 provides hints regarding the differences when using SAs in a similar way.

06-Dec-2013 | AN-No. 1MA226

The R&S® Broadcast Test Center BTC supports the new “Next Generation Broadcast Standard ATSC 3.0” with BTC firmware version 2.20 and later.This application note describes the necessary settings in the user interface of the R&S® Broadcast Test Center BTC.

27-Mar-2018 | AN-No. 1GP119

The following paragraphs are intended to show the capabilities of the Rohde & Schwarz Signal Generator SMT performing ILS and Marker Beacon receiver tests. The procedures presented should not be considered binding or mandatory. It is expected that the user once familiar with the use of SMT for VOR/ILS receiver tests will design and implement procedures which satisfy equipment and regulatory requirements.

06-Jul-1994 | AN-No. 1GPAN11

Secondary surveillance radar (SSR) bridges the gap between communications systems and classic radar systems. Despite the increasing capabilities of mobile communications, SSR remains a major component in airspace surveillance. State-of-the-art methods such as Mode S reply enhance SSR with broadcast-like capabilities and enable airports in remote locations to surveil the airspace even if no radar is available. More advanced techniques such as automatic dependent surveillance broadcast (ADS-B) utilize the infrastructure provided by a Mode S reply transponder to provide even more information for ground control and other aircraft.

17-May-2021

Voice over IP for air traffic control

21-Nov-2014

Test time is a critical parameter when it comes to evaluating the cost of test.This application note describes typical spectrum analyzer measurements in production environments and discusses different approaches to speed them up.

17-Nov-2014 | AN-No. 1EF90

This application note illustrates the upgrade from the available wireless TV standard ATSC to its expansion ATSC Mobile DTV described in the new standard A/153 (ATSCM/H), in which Rohde & Schwarz has played a major development role. An upgrade package makes it possible to efficiently extend existing ATSC infrastructures for ATSC Mobile DTV services. A central component of the ATSC Mobile DTV equipment is the R&S®AEM100 multiplexer. Together with the R&S®AVE264 H.264 Encoders, digital TV exciter (R&S®SX800) and Transmitters, it forms a complete ATSCM/H system.

22-Sep-2009 | AN-No. 7EB02

This Application Note provides guidance on using the “Intermodulation Wizard” through an example measurement.

27-Mar-2013 | AN-No. 1EZ63

In accelerator physics, pulsed signals frequently need to be measured. The digital trigger and low noise frontend of the R&S®RTO/RTP digital oscilloscope make it possible to perform the high precision measurements needed to characterize the experimental setup. Several measurement functions specially developed for accelerator physics labs support detailed signal analysis.

17-Dec-2013

Integrating the R&S®SMBV100B GNSS simulator into the AVL DRIVINGCUBE™ toolchain creates new possibilities for validating advanced driver assistance systems and autonomous driving functions at the vehicle level. Combining a complete vehicle on a vehicle test bed with physical sensor stimulation results in fast, reproducible and cost-efficient testing. All possible driving scenarios can be executed under realistic and safe conditions.

09-Jan-2020

The R&S®FSWP phase noise analyzer is a highend instrument designed to accurately analyze noise performance of key components in radar and communications systems. Using phase noise measurements, a device’s large-signal noise figure can be derived under real-world operating conditions.

27-Oct-2017

Deembedding, often a necessary and complex task, is made easier with an integrated hardware and software solution.

25-Sep-2018

Need: easy exchange of multiple versions of content as one package in a digital formatSolution: interoperable master format (IMF) and R&S®CLIPSTER

26-Sep-2018

A special requirement for testing GSM components is to measure the electrical characteristics, such as the gain of a power amplifier, of the DUT under pulsed conditions. The test should be similar to real operating conditions for a mobile telephone.

28-Jul-1998 | AN-No. 1EZ42

This application note describes different measurement techniques and methods for an automotive lighting module based on a hybrid controller design. Of course, a lighting module in such an environment has to fulfil requirements according to the automotive standard, which is typically a relatively high-level standard compare to the industry standard. The oscilloscope is a perfect tool for this application to verify the set of requirements because time domain signals (analog and digital) are present in the whole design. Furthermore, measurements in the frequency domain have to be performed, which a modern oscilloscope can fulfil. In addition to the oscilloscope, a programmable power supply supports the measurement in several measurements. The set of requirements are the main reason why a hybrid controller from Microchip is a great choice for this design because it provides tremendous analogue and digital capabilities. The hybrid controller provides beside the analogue functions like an operational amplifier digital functions like analog-to-digital converter and interface functions like UART, CAN or LIN to interact with other systems. The programmable software part is hosted in the digital part. The digital part of the controller implements the communication interface and provides status information to the outer system controller. The light source itself has to avoid any flicker and shall be capable to dim to different lighting levels. Wide input voltage variations and efficiency have to be taken into account during the design of a converter dedicated for automotive applications. Nevertheless, the measurement considerations presented with the design are valid and applicable in other professional lighting industries as well.Thanks to Mr. Andreas Reiter and Mr. Milan Marjanovic from Microchip who provided us with hardware and software and their great expertise to create this application note.

08-Jun-2020 | AN-No. GFM339

As phase noise becomes an increasingly important system-level specification for electronic test equipment, communications systems, and radar systems. It is not only important to quantify the noise produced by oscillators, but also the noise added by each component in the signal processing chain. This application note reviews the fundamentals of residual or additive noise and addresses measurement techniques for determining the amplitude (AM) and phase noise added by two-port devices such as: amplifiers, mixers, block frequency converters, multipliers, dividers, and frequency synthesizers.Additionally, the Rohde & Schwarz FSWP phase noise analyzer will be introduced and a discussion of residual noise measurement techniques for the above-mentioned devices will be provided.

09-Oct-2017 | AN-No. 1EF100

Rohde & Schwarz presents a customizable solution for testing GNSS receivers to ensure a certain resilience against (legal) interference from neighboring bands.

18-Jul-2017

This application note describes the different memory types and locations that user information can be stored in a spectrum analyzer R&S® FSEA, R&S® FSEB, R&S® FSEM, R&S® FSEK or R&S® FSIQ, as well as the different ways in which it can be erased/cleared for security reasons.

20-Sep-2004 | AN-No. 1EF54

Sequencing of waveforms is a technique used to play back multiple test signals fast and flexibly using an arbitrary waveform generator (ARB). Multiple ARB waveforms can be combined to generate all kinds of test signals sequences. Switching from one waveform to the subsequent waveform in the sequence is instantaneous, which enables high-speed operation for production testing. This application note explains how to generate such signal sequences using vector signal generators from Rohde & Schwarz. The examples provided show the required instrument settings and possible fields of application for waveform sequencing.

29-Feb-2012 | AN-No. 1GP53

Capturing small ECG signals in medical applications The R&S®RTE is the best choice for analyzing small signals such as ECG signals with high signal fidelity. Capturing small ECG signals in medical applications Capturing small ECG signals in medical applications The R&S®RTE is the best choice for analyzing small signals such as ECG signals with high signal fidelity. Capturing small ECG signals in medical

17-Nov-2015

Software tool for fast and repeatable optimization of signal analyzer RF front-end settings

The signal conditioning in the RF front-end of signal analyzers is crucial to achieve the best performance with respect to image-suppression, noise-floor, dynamic range and other RF-key parameters.Precise signal levelling is especially important for complex measurements like Error-Vector-Magnitude (EVM). To minimize the measurement uncertainty from test system contributions over a wide range of different levels, the RF front-end needs to be adapted continuously according to the signal characteristics, signal power and frequency - ideally using an automatic levelling algorithm.This document describes the approach of a waveform specific, on-site characterization of the signal analyzer: For each waveform and frequency of interest, the instrument is evaluated in a first step. With this additional data, a fast and repeatable auto-levelling can be performed during the actual measurement.

24-Jan-2022 | AN-No. 1EF111