This document describes the adaptive frequency hopping mechanism for improved signaling performance in Bluetooth Basic Rate and Enhanced Data Rate devices.The R&S CMW provides this feature for remote operation in TX, Loopback and Connection test mode. Thereby the R&S CMW acts as a master, while the Equipment under Test (EUT) represents the slave(s) of the piconet.

14-Dec-2016 | AN-No. 1C108

Today virtually every electronic device has a standby mode. Power consumption is regulated in most countries by increasingly stringent limits. This makes standardized power measurement essential.

12-Sep-2018

Best practices for national regulatory authorities

Key points:Importance of field measurements: Traditional network planning tools and models only offer an estimated view of mobile coverage. Field measurements are conducted under real geographical and load conditions, and therefore provide a more accurate picture and can discover interferences more effectively. Coverage investigations: When deploying a mobile network, operators must adhere to regulatory standards and licensing conditions. As a result, regulatory authorities carry out field measurements on a regular or ad hoc basis to validate compliance or investigate customer complaints. This process identifies coverage gaps and areas of poor network quality, enabling regulatory authorities to take actions to enhance service quality for consumers and guide network expansion.Foster competition: If the field measurements of the coverage and performance are performed on a scale representative of a given country, the transparency of these results can promote healthy competition between operators and better service for consumers, which is essential for economic growth and social development.Measurement Techniques: The harmonized methodology for measuring and evaluating data throughput and QoE based on popular services is described in ETSI TR 103 559.

15-Apr-2024 | AN-No. 8NT14

Using a Vector Network Analyzer from the ZVR family, not only magnitude and phase can be measured, but also group delay and even phase delay. Whereas phase delay measurements produce the highest accuracy for the electrical length of non-dispersive devices under test, such as coaxial cables, group delay measurements also give a detailed insight into the frequency dependent delay characteristics of dispersive devices, such as filters. In addition to the traditional step aperture technique, Vector Network Analyzers from the ZVR family offer a frequency aperture technique, which allows a well defined and constant aperture for group delay measurements also for a nonlinear frequency sweep.

28-Jul-1998 | AN-No. 1EZ35

A collection of frequently occurring customer questions on using the ZVR analyzer, calibration, virtual transform networks, and additional applications.

23-Jan-2002 | AN-No. 1EZ38

Embedding and De-Embedding of virtual transformation networks for measuring scattering parameters with a ZVR or ZVC vector network analyzer.

25-Sep-1998 | AN-No. 1EZ45

The R&S® ZVA-Z110 converters offered for the R&S® ZVA family enable network analysis in the W band (75 GHz to 110 GHz). In this Application Note, measurements with three or four converters will be discussed. Test configurations for such measurements have so far been implemented only with coaxial connector systems for a frequency range up to approx. 40 GHz. The term 'multiport measurements' was created for this type of measurements.

09-Oct-2007 | AN-No. 1EZ56

IoT devices have tight requirements for power consumption in order to achieve expected battery life times of multiple years without a connection to a power supply. In order to verify the power consumption and expected battery life time, voltage and current have to be measured accurately for different operating states of the device under test.This application note explains battery life tests using RT-ZVC in combination with CMWrun and CMW500, including example applications.The solution by Rohde & Schwarz enables precise voltage, current and consequently, power measurements.The RT-ZVC Multi-Channel Power Probe can be driven as part of a test plan combining signaling and power measurements for a detailed view of the power consumption in different signaling states as well as an estimation of overall lifetime given a certain battery capacity.

17-Feb-2017 | AN-No. 1MA281

This document provides some technical background and guidance on how to optimize the measurement of one of the key performance parameters of WLAN transmitters - the Error Vector Magnitude (EVM).

IEEE 802.11be Extremely High Throughput (EHT), also known as Wi-Fi 7, is the latest amendment of the IEEE 802.11 standard and is still under development. This amendment focuses mainly on improved throughput. To do so, the most notable changes currently implemented are:► New modulation scheme: 4096-QAM (4K-QAM)► Larger bandwidth: 320 MHz► Support for 16x16 MU-MIMO► Enhanced resource allocation in OFDMAThis places special demands on the measurement equipment.

06-Sep-2022 | AN-No. 1EF114

This application note introduces the IVI High Speed LAN Instrument Protocol (HiSLIP) and outlines its features. HiSLIP is the successor to the VXI-11 LAN remote control protocol. This document also describes guidelines for using this protocol.

12-Nov-2014 | AN-No. 1MA208

Increasing demands on power distribution networks have resulted in smaller DC rails, as well as a proliferation of rails that ensure clean power reaches the pins of integrated circuits.

07-Mar-2017

VSC4G, VCS-G4, VSC, CERTIUM Rohde & Schwarz solution CERTIUM VCS CERTIUM VCS for VoIP radio interconnection with traditional VCS for step-by-step transition to VoIP VSC4G, VCS-G4, VSC, CERTIUM Rohde & Schwarz solution CERTIUM VCS CERTIUM VCS for VoIP radio interconnection with traditional VCS for step-by-step transition to VoIP VSC4G, VCS-G4, VSC, CERTIUM Rohde & Schwarz solution CERTIUM VCS

24-Jul-2023

GPRS (General Packet Radio Service) and EDGE (Enhanced Data Rates for GSM Evolution) provide data capabilities in widely deployed 2G networks reaching peak and average data rates of 384kpbs and 200kbps, respectively. Within 3GPP Release 7, further improvements to GPRS/EDGE have been specified in the context of EDGE evolution. This application note introduces key features of EDGE evolution and outlines the changes to the radio interface.

02-Apr-2008 | AN-No. 1MA129

This application note explains how to bring a CADENCE system which is attached to an R&S EX-IQ-BOX into service for the first time. The first part of the document shows how to setup an LTE Demo without using a UE design. This setup uses the R&S CMW500 as the downlink transmitter. The emulator receives the downlink via an R&S EX-IQBOX and passes it to an R&S spectrum analyzer (R&S FSx) via a second R&S EXIQ-BOX. The second part describes the real wiring using up- and downlink. This will only work if a UE design is available on the emulator.

30-Jun-2011 | AN-No. 1CM75

Offering bandwidths up to 160 MHz, the signal generators and analyzers from Rohde & Schwarz are ideal for testing IEEE 802.11ac signals

27-Jun-2013

New technologies and applications like 6G communications and sensing extend into sub-THz frequencies in the D band and beyond. New semiconductor technologies and processes need to be commercialized to support these efforts.

12-Dec-2023

In general, most of the existing electronic devices are connected to the AC mains and require a power conversion stage to convert the AC-Voltage to a smaller DC-Voltage. Voltages and frequencies of the power grid differ between different regions. However, different types of AC-DC conversion stages exist to supply the electronic equipment with adequate DC-power.In AC-DC conversion combined with power levels less than 50W, the flyback converter is a commonplace chosen topology because of its simplicity and its low cost. The majority of consumer products make use of this converter type like wall brick power supplies or power adapters for any consumer application and other type of stand-by auxiliary power supply like used in white and brown goods. In AC to DC converter application, an electrical isolation between input and output is mandatory. The flyback topology provides this galvanic barrier.Beside the common advantages of a flyback converter, it has inherently parasitic components, which typically produce ringing waveforms with considerably high voltage spikes. Without suppressing this unwanted ringing, it may have some negative effect on other components like the switching elements. This ringing can also influence the EMI emissions adversely. Therefore, it is an important task to adequate suppress and damp the ringing effect. This damping circuit is known as snubber circuit and provides this functionality. In the flyback converter, different snubber structures can be applied and each of the structure has its advantage and disadvantage.The demand having a snubber circuit in the power supply topology leads to specific verification methods during the design to obtain a proper and reliable design. These verification methods are the main focus of the discussions within this document.

23-Jun-2021 | AN-No. 1SL363

The Doherty Amplifier continues to be rolled out in an increasing number of TxFE (Transmit Frontend) applications, as the quasi-linear amplifier architecture of choice.The advent of 5G, with its inevitable microwave or millimeter wave air interface, increase the design challenges associated with its construction; not least of all because of the potential for increased dispersion in the constituent amplifiers and combiners.This application note describes a measurement-based development methodology by which the Doherty Amplifier may be enhanced, increasing performance and/or performance bandwidth. This methodology is supported with a working example.The methodology may also be extended to balanced, spatially combined and anti-phase (so called "pushpull" or "differential") amplifiers, the latter often itself nested in Doherty configurations.The R&S®Quickstep sequencing software may be downloaded from:

26-Sep-2016 | AN-No. 1MA279

This application note describes how to convert GPS routes from NMEA 0183 file format to waypoint files that can be used by the R&S®SMU200A Vector Signal Generator.

26-Sep-2008 | AN-No. 1MA133

Voice over IP for air traffic control

21-Nov-2014

This document describes how the advanced calibration techniques of the ZVA Vector Network Analyzers can solve the challenges of measuring the S-Parameters on impedance matching devices. The document describes the concept and setup required to perform the calibration of the ZVA and making the measurement. The procedure described in this application note applies to the ZVB and ZVT Vector Network Analyzers as well.

06-May-2009 | AN-No. 1EZ59

For cable TV, the "last mile" to the connection at the home is the bottleneck that prevents higher data rates. The last mile is made up of optical fiber and coaxial cables, amplifiers and electrical/optical converters. This mix of optical fiber and coaxial cables is known as a hybrid fiber coax (HFC) network. One option for cable network providers to maximize both the downstream (DS) and upstream (US) data throughput using the existing cable TV network, but without making expensive changes to the HFC network infrastructure, is to employ the data over cable service interface specification (DOCSIS) 3.1.This Application Note discusses the fundamental technological advances of DOCSIS 3.1 and presents measurement solutions from Rohde & Schwarz.

02-Mar-2015 | AN-No. 7MH89

The R&S®SMW200A together with the R&S®FSW is a state of the art testing solution that significantly reduces the required hardware for testing power amplifiers with envelope tracking and/or digital pre-distortion. This application note introduces the test solution in detail and presents corresponding measurement examples.

25-Sep-2014 | AN-No. 1GP104

Before devices can be used in a LoRaWANTM network, they must among other things meet country-specific wireless communications regulations. This application note shows developers and manufacturers of devices with LoRa wireless technology how transmitter measurements are conducted in line with FCC Part 15.247. It also describes how important receiver characteristics can be verified by metrological means. In this context, battery life in particular plays a key role in IoT applications. A further chapter describes how current consumption of LoRa wireless modules can be measured reliably.

29-Nov-2017 | AN-No. 1MA295

This application note describes ATSC Mobile DTV standard A/153, ATSC-M/H. This standard is completely implemented in the R&S®AEM100 ATSC-M/H Emission Multiplexer.

22-Jan-2011 | AN-No. 7EB01

Most of the tests specified in standard TS 34.121 [1] for 3GPP Rel-6 can be performed with R&S®CMU200. This document provides a step by step guide on how to perform Rel-6 measurements on transmitter characteristics and performance tests according to TS 34.121 V8.7.0 clauses 5 and 10 with stand-alone R&S®CMU200. Test cases that require additional instruments, e.g. fading generator (R&S®SMU200A or R&S®AMU200A) will be discussed in brief in this application note with recommended reference. A set of *.sav files based on R&S®CMU200 firmware V5.03 for UE supporting operating band I and power class 3 in RMC 12.2 kbps + HSPA is attached to this application note.

07-Oct-2009 | AN-No. 1CM73

With advances in digital signal processing techniques modern wireless communications systems and radar systems have become increasingly digital and more constraints have been placed on packing more information into less and less bandwidth. On the wireless side, modulation formats have become more complicated with less margin for symbol error. On the radar side, modern radar systems are trying to extract more information about the targets they track and provide the ability to track slow moving targets such as automobiles and personnel in the presence of clutter.For both communications and radar systems one of the key RF parameters that limits system performance is phase noise. As systems engineers develop new and more advanced RF systems, phase noise of oscillators and transmitters can no longer be overlooked.This application note will focus on phase noise measurements for pulsed RF carriers such as those used for radar systems. We will address some of the physical limitations relating to pulsed phase noise measurement and introduce the capabilities of the new Rohde & Schwarz FSWP phase noise analyzer.

18-May-2016 | AN-No. 1EF94

1EF86 LTE, MIMO, LTE-MIMO, RTO1044, SMU200A, K102, K103, K102PC, K103PC Testing LTE MIMO Signals using a R&S RTO Oscilloscope Testing LTE MIMO Signals using a R&S®RTO Oscilloscope 1EF86 LTE, MIMO, LTE-MIMO, RTO1044, SMU200A, K102, K103, K102PC, K103PC Testing LTE MIMO Signals using a R&S RTO Oscilloscope

24-Apr-2013 | AN-No. 1EF86

The R&S®RTO / R&S®RTE oscilloscope is a valuable tool for analyzing EMI problems in electronic designs. High input sensitivity, high dynamic range and a powerful FFT implementation are key features for capturing and analyzing unwanted emissions.

26-Feb-2015

Performing essential RF tests gets your Sigfox device ready for certification and deployment

15-Nov-2018