22 Results
Automated testing against the Chinese national GNSS test standard (GB/T 45086.1‑2024) with R&S®CMWrun sequencer software and the R&S®SMBV100B vector signal generator
20-Feb-2025
End-to-end conformance testing of 4G and 5G next generation eCall (NG eCall) modules under controlled network conditions
13-May-2024
This application note addresses the diverse possibilities of interoperability between Rohde & Schwarz power sensors and Rohde & Schwarz signal generators. All current and many legacy Rohde & Schwarz signal generators offer the capability of directly connecting power sensors. This enables power measurements without the need of a base unit or separate PC to display the readings. Furthermore, sensors can be used for special tasks like filling a user correction table or continuously controlling levels at crucial points in the measurement configuration.
31-Aug-2023 | AN-No. 1GP141
Create and simulate detailed traffic situations for the verification of cellular V2X (C-V2X) connectivity
30-Jun-2022
The R&S®CMW500 and R&S®SMBV100B are the ideal team for motor vehicle type approval testing of your eCall and ERA-GLONASS cellular modems and their GNSS receivers in line with the EU2017/79 regulation.
02-May-2022
This application Note is based on CMW500, SMBV100B and Vector CANoe.Car2x Software and guides to how to simulate the specific Cellular Vehicle-to-Everything (C-V2X) wireless environment in respect to road transport scenarios and transmitted messages around the Device Under Test (DUT) like a Telematics Control Unit (TCU). It shows how to verify and validate the C-V2X application of the DUT in laboratory environment. The virtual simulation scenario is not limited to the requirements of CSAE53-2017 specification, and it could be modified by user according to this operating guide with CANoe.Vehicle-to-everything (V2X) is a new generation of information and communications technologies that connect vehicles to everything. The objective of V2X is to increase road safety and manage traffic efficiently.C-V2X is designed to offer low-latency vehicle-to-vehicle (V2V), vehicle-to-roadside infrastructure (V2I) and vehicle-to-pedestrian (V2P) communications services to add a new dimension to future advanced driver assistance systems (ADAS). C-V2X as one communications standard defined by 3GPP in Release 14 uses LTE technology as the physical interface for communications. The standard describes two types of communications. The vehicle-to-network (V2N) communications type, exploits the cellular Uu interface, uses traditional cellular link to enable cloud services to be integrated into end-to-end solutions, e.g. to allow road and traffic information for a given area to be distributed to the vehicles.The second type is referred to as direct or PC5/Sidelink (V2V, V2I, V2P) communications, where data transmission takes place over the PC5 interface. In that type, C-V2X does not necessarily require a cellular network infrastructure. It can operate without a SIM and without network assistance and uses GNSS as its primary source for time synchronization.Verifying system functionality and performance exclusively by field testing in a real-world environment can be time-consuming, costly and very challenging. Requirements regarding functionality, and consequently the required assistance functions, are constantly changing. Due to this fact, test solutions are needed during the development and introduction phase to verify compliance with the standards. The PC5 direct communications type allows exchange of time sensitive and safety relevant information. Using a mobile communication tester like the R&S® CMW500 together with a C-V2X scenario simulation tool delivers reproducible test scenarios. This is essential for the standardization of verification processes for C-V2X in order to obtain reliable and comparable results, and it helps to demonstrate that end-to-end functionality between two C-V2X devices from different vendors works properly.
02-Jun-2021 | AN-No. GFM341
conducted conformance testing according to TS 38.141-1, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes how all mandatory RF transmitter tests (TS 38.141-1, chapter 6), according to Release 16, can be performed quickly and conveniently with signal or spectrum analyzers from Rohde & Schwarz by either choosing manual operation or a remote control approach. Moreover, some test cases require additional signal generation equipment from Rohde & Schwarz.In Addition, a new Python software library comes with this application note to enable the remote control approach of base station testing. This example requires the RsInstrument module which can be found on pypi.org or installed via 'pip' and is provided as is.
27-Jan-2021 | AN-No. GFM313
conducted conformance testing according to TS 38.141-1, Rel. 15
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes how all mandatory RF receiver tests (TS 38.141-1, chapter 7), according to Release 15, can be performed quickly and conveniently with signal generators from Rohde & Schwarz by either choosing manual operation or a remote control approach. Moreover, one test case requires a signal or spectrum analyzer from Rohde & Schwarz which is highlighted seperately in the corresponding chapter.In Addition, a new Python software library comes with this application note to enable the remote control approach of base station testing. This example requires the RsInstrument module which can be found on pypi.org or installed via 'pip' and is provided as is.
02-Dec-2020 | AN-No. GFM314
radiated conformance testing according to TS 38.141-2, Rel. 16
3GPP defines the Radio Frequency (RF) conformance test methods and requirements for 5G NR Base Stations (BS) in the technical specifications TS 38.141. This application note describes all mandatory RF receiver tests (TS 38.141-2, chapter 7), according to Release 16.Furthermore, this document provides a brief introduction about the different R&S OTA antenna test solutions and how they are applicable for base station conformance testing. Rohde & Schwarz offers suitable solutions for any test case that is mentioned in this application note.
30-Jun-2020 | AN-No. GFM325
The vector signal generators and GNSS simulators R&S®SMW200A and R&S®SMBV100B are remote-controllable in realtime and can therefore be implemented into a dynamic HIL environment. The HIL simulator can dictate position coordinates, kinetic parameters, and vehicle attitude information based upon which the R&S® GNSS simulator updates the simulated receiver movement in realtime. This application note presents background information and details about operating a R&S® GNSS simulator in HIL applications.
14-Apr-2020 | AN-No. 1GP102
Integrating the R&S®SMBV100B GNSS simulator into the AVL DRIVINGCUBE™ toolchain creates new possibilities for validating advanced driver assistance systems and autonomous driving functions at the vehicle level. Combining a complete vehicle on a vehicle test bed with physical sensor stimulation results in fast, reproducible and cost-efficient testing. All possible driving scenarios can be executed under realistic and safe conditions.
09-Jan-2020
Create and simulate detailed traffic situations for the verification of cellular V2X (C-V2X) connectivity.
18-Nov-2019
The R&S®SMBV100B signal generator offers a remote emulation feature that makes it possible to control the instrument by commands other than the built-in native SCPI commands. This feature allows the user to replace signal generators, e.g. from other manufacturers, with the R&S®SMBV100B without having to change the remote control code.This application note describes how to use the remote emulation feature in general. Furthermore, it describes in detail the remote emulation for each supported instrument, limitations of the individual emulations and the remaining differences between the emulated and the original commands.
30-Sep-2019 | AN-No. 1GP121
The R&S®SMBV100B vector signal generator can be turned into a multi-frequency, multi‑constellation GNSS simulator for receiver tests in the lab.
22-Aug-2019
Next Generation Emergency Call (NG eCall) is a extension of eCall, a service provided in Europe with the goal of reducing response times for accidents or other emergencies on the roadways. This application note briefly describes the technology behind NG eCall and presents conformance tests for NG eCall using the R&S®CMW500 RF tester and either the R&S®SMBV100B or the R&S®SMW200A vector signal generator. The test software for NG eCall (R&S®CMW-KA096) makes it quick and easy to perform these tests with the LTE wireless communications standard.
06-Jun-2019 | AN-No. GFM312
The hardware-in-the-loop options for the R&S®SMBV100B and the R&S®SMW200A GNSS simulators enable realistic, cost-efficient and flexible testing in a user-controlled environment.
03-Jun-2019
The ARB Toolbox is an easy-to-use, feature packed software package that is used for many ARB waveform related tasks. Use this software for creating ARB waveform files from custom IQ data; import data from MATLAB .mat files; evaluate waveform content graphically; resample or filter waveforms; create analog modulated signals as ARB files; edit marker data in waveform files; use the composer for the creation of complex multi carrier scanarios.
13-Dec-2018 | AN-No. 1GP88
Performing essential RF tests gets your Sigfox device ready for certification and deployment
15-Nov-2018
1MA196 1MA196, Forum, Instrument, Remote, Control, Python, R&S Forum, RS Forum, R&SForum, RSForum R&S®Forum for Instrument Remote Control Using R&S®Forum Application for Instrument Remote Control 1MA196 1MA196, Forum, Instrument, Remote, Control, Python, R&S Forum, RS Forum, R&SForum, RSForum R&S®Forum for Instrument Remote Control
28-Jun-2018 | AN-No. 1MA196
Versatile Software Tool for Rohde & Schwarz Instruments
RSCommander is a versatile software tool for a wide range of Rohde & Schwarz spectrum-, network analyzers, signal generators and oscilloscopes. It allows for automatic instrument discovery, making screenshots, reading traces, file transfer and simple script creation.
24-Dec-2017 | AN-No. 1MA074
Before devices can be used in a LoRaWANTM network, they must among other things meet country-specific wireless communications regulations. This application note shows developers and manufacturers of devices with LoRa wireless technology how transmitter measurements are conducted in line with FCC Part 15.247. It also describes how important receiver characteristics can be verified by metrological means. In this context, battery life in particular plays a key role in IoT applications. A further chapter describes how current consumption of LoRa wireless modules can be measured reliably.
29-Nov-2017 | AN-No. 1MA295
This application note explains how to convert different Rohde & Schwarz I/Q file formats among each other using the supplied software tool.
23-Sep-2015 | AN-No. 1EF85