The R&S®ZNL is an economic solution that can characterize a variety of DUTs both via network analysis and spectrum analysis without requiring a lengthy setup.

17-Dec-2021

An automated test solution based on the R&S®CMW wideband radio communication tester fully supports the new test cases for real-time submeter positioning.

10-Jun-2022

Simulation of BCCH Channel of GSM/PCN Base Station with Signal Generator SME

01-Jul-1999 | AN-No. 1GPAN14

This application note provides practical hints to accurately characterize and de-embed these lead-in and lead-out structures with R&S Vector Network Analyzers ZNA, ZNB, ZNBT and ZND.

19-Sep-2022 | AN-No. 1SL367

This application card will give some guidance as to the possible combinations of bandwidth options and mixers in conjunction with the needed IF frequencies.

16-Jun-2020

Selecting Your Next Oscilloscope:

If you are selecting your next oscilloscope and want more insight on how to understand ENOB values measured and published by oscilloscope manufacturers, this document is for you. The effective number of bits (ENOB) is a way of quantifying the quality of analog to digital conversion. A higher ENOB means that voltage levels recorded in analog to digital conversion are more accurate. Understanding oscilloscope vendor-supplied ENOB values can be complex. This document focuses on interpretation of measured ENOB results made on oscilloscopes rather than the math behind ENOB calculations.

21-Jun-2024 | AN-No. 1TD12

Tolerance to Noise Tests for DTV Receivers

26-Jan-2007 | AN-No. 7BM64

This paper describes the measurement of additive/residual phase noise of power amplifiers or multipliers for example for automotive RADAR sensors at 80 GHz using the interferometric measurement approach in combination with a phase noise and VCO tester R&S FSWP. The setup provides a way to characterize the additive/residual phase noise of amplifiers down to -150 dBc/Hz at 100 kHz offset even in the microwave range at 80 GHz.

11-Sep-2024 | AN-No. 1EF117

The R&S ® TSStream multi-TS streaming software streams a number of MPEG transport stream files simultaneously over a single IP interface.

16-Mar-2017 | AN-No. 1GP113

R&S CMWrun Sequencer Software Tool

20-Feb-2015

Rohde & Schwarz offers RF solid-state amplifiers for various frequencies ranging from 9 kHz to 6 GHz and delivering CW power up to 80 kW.

27-Apr-2016

This application note describes the basic frequency filter measurements that are often required during service repairs, during development and for training purposes.

27-Mar-2015 | AN-No. 1MA243

Measurements on AMPS phones with the R&S CMU200 and CMUgo

07-Sep-2004 | AN-No. 1CM53

LTE-A Base Station Receiver Tests

11-May-2016 | AN-No. 1MA195

This document is divided in two parts and starts with an introduction in AC-DC conversion principles in general. It will present the most common circuits used for different power levels. The switching mode power supply (SMPS) converter will be the main focus as they are used everywhere in the electronics. Especially the flyback converter design in different flavors are highlighted. Nevertheless, all measurements are also applicable for other SMPS converter designs operating at higher power levels.In the second part of this document, most relevant testing methods and procedures of an AC-DC converter are highlighted. For each testing section, a fundamental part will be upfront discussed and it is followed by a presentation of a suitable measurement method. In this second part, the device under test (DUT) is considered as black box device and thus the structure is similar. Therefore, the testing parts consists of methods related to input tests, output tests and a combination of both like efficiency. Of course, some test performed at the output of the converter are also relevant for DC-DC converter, e.g. the validation of the output ripple.

14-Nov-2022 | AN-No. 1SL387

CDMA2000® Base Station Test with R&S Equipment

05-Sep-2003 | AN-No. 1MA61

This application note describes a test scenario tor cable components with an R&S®CLGD Cable Load Generator and an R&S®FSW Signal & Spectrum Analyzer.

24-Jan-2017 | AN-No. 1MA285

Generation and Analysis of ZigBee™ IEEE802.15.4 signals in the 2.4 GHz band

21-Jun-2007 | AN-No. RSI03

Generating Interference Signals using the R&S SFU-K37 Option

09-Jan-2007 | AN-No. 7BM50

Optimizing electric drivetrains with MXO oscilloscopes

12-Mar-2024

This paper explains how to use the Rohde & Schwarz IVI.NET instrument drivers in a Visual Studio environment.

31-May-2016 | AN-No. 1MA268

High-speed serial interfaces often transmit data with differential signaling and differential probes can be used to access signal traces. In addition to differential inputs, these probes have a ground connection.

02-Nov-2022

Testing radar warning equipment in realistic scenarios is crucial to reliable field performance. Commercial vector signal generators (VSG) such as the R&S®SMW200A from Rohde & Schwarz have become a very attractive alternative thanks to their increased available bandwidth and processing power.

13-Aug-2020

Remote Operation of R&S Instruments Using Remote Desktop Connection via LAN

05-Jul-2007 | AN-No. RAC-0703-0029

Firewall configuration for R&S DVM

23-Nov-2004 | AN-No. 7BM46

This application note explains how to setup R&S®AdVISE to monitor the temperature of an EUT by using an infrared camera.

14-Sep-2020 | AN-No. 1S008

Monitoring on up to 10 000 channels with different parameter settings

13-Jul-2012

Test of DVB-H Capable Mobile Phones in Development and Production

07-Apr-2005 | AN-No. 1MA91

Verifying RF ports is crucial for minimizing lost power and maximizing battery life. The R&S®FPC1500 is an easy-to-use and costeffective tool for this type of verification.

05-Mar-2020

Use R&S®RTP high-performance oscilloscopes and the R&S®VSE-K6A phased array measurement option for analyzing deceptive jamming techniques and automating jamer testing.

12-Jul-2021