How can I change the display resolution when I use an external monitor?

Converting the real and imaginary numbers to magnitude in dB and phase in degrees.

Sending a remote Control Command internally

What is the correct pin layout of the DC inputs on the network analyzer's rear panel?

I have set my VNA to single sweep mode and switched on averaging with a factor of 10. But when I restart the single sweep, it stops after 1 sweep and the averaging is not done.

R&S ZV-ZCAN Calibration Kit - Product Brochure

R&S®ZV-Z170 Calibration Kit - Specifications

R&S ZV-ZCAN Calibration Kit

Describes all instrument functions and remote control commands, as well as measurement and programming examples.

Provides information on security issues when working with R&S®ZVAX-TRM in secure areas.

Provides the information required to prepare the instrument for use and start working.

This application note describes how to configure a Rohde & Schwarz Network Analyzer to make spectral measurements directly on a device under test.

16-Mar-2012 | AN-No. 1EZ62

TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines

I trigger this single sweep with the RSZVB_Send_Trigger_and_Wait_for_OPC driver, but this driver does not wait for the complete 10 sweeps. If I don't use averaging, this program is works.

I query the values of a trace using scpi commands. But I get the y-values only. Is there a possibility to get the y-values also (frequency)?

I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.

How can I switch from remote to local state via remote control?

This presentation discusses a world-first source-load pull system centred around the R&S®ZVA vector network analyser and 110 GHz passive tuners.

The R&S®ZVA vector network analyzer in combination with the R&S®ZVAB-K30 noise figure measurement option simplifies noise figure measurement, a key parameter for receiver performance evaluation.

TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?

This application note describes the techniques to measure the dielectric properties of materials using a vector network analyzer. It also shows methods for converting the s-parameters to dielectric properties.

23-May-2012 | AN-No. RAC-0607-0019

ZVA Vector Network Analyzers, PIM, Rohde & Schwarz demonstrated fast and accurate passive intermodulation (PIM) testing of duplex filters at the European Microwave Week 2013 in Nuremberg.

Choose Rohde & Schwarz test solutions for passive components for reliable test results and test speed reasons.

I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?

This paper shows how to perform a n-port multi-port calibration by using calibration unit with a lower number of ports than available of the vector network analyzer.

06-Feb-2013 | AN-No. 1EZ70

Here you will find bargains like the latest generation test and measurement instruments which have been used by our sales teams for demonstration, training and loan.

This document describes how a Windows®-based R&S® T&M instrument is remotely operated by an Android™ tablet as if working on it locally.

22-Aug-2013 | AN-No. 1MA236