Search

NRX set measurement result as reference value for relative measurement via remote control

With the NRX how can I set a measurement result directly as a reference value for relative measurement via remote control?

How to use the User Def. Math functionality

Number of harmonics in RTE/RTO Power option

Number of harmonics, RTE, RTO, Power option, FAQ

Programming the AM300 in LabView

FAQ; Programming the AM300 in LabView

ZNA / ZVA / ZNB - no correction data for Sliding matches?

I got a calibration kit with a sliding match standard. But there are no correction values for the NWA supplied.

TSEMF-Bx isotropic antenna is not detected by the FSH4/FSH8

UNCAL

GPIB sequence for performing the "normalization" calibration method

When do I need the EMC32 User Administration?

FAQ: When do I need the EMC32 User Administration?

Change the byte order in FORMAT REAL

Remote Control: Change the byte order in FORMAT REAL

How to use the binning function for component sorting

I want to use the LCX series LCR Meter to automatically control and sort components. One of the tasks is to differentiate between the following three values of resistors: - Less than 990 Ohm, - Middle range from 990 to 1010 Ohm (1 kOhm), - More than 1010 Ohm. How can I set this measurement up and which pins do I have to use at the 15 PIN SUB-D socket at the rear side of the LCX?

What is the Structure of FSE/FSIQ Trace Data on the GPIB?

Set Trigger Source to AM for FSMR

I want to set the trigger source of my FSMR to AM. But it always sets the trigger source to RF level. How can I set the trigger source to AM ?

How can I save the complete device information of my CMA 180 to a USB stick?

ZNA - Spectrum Analysis with converters

Does the option ZNA-K1 (Spectrum analyzer mode) also work with the Millimeterwave Converters?

Self Alignment via remote control via TCP/IP => 'CAL?

Single Pulse via the HMF2525/HMF2550 Signal Generator by using the enter key as a trigger source

Single Pulse via the HMF2525/HMF2550 Signal Generator by using the enter key as a trigger source Single Pulse via the HMF2525/HMF2550 Signal Generator by using the enter key as a trigger source

Compatible Firmware Versions

FAQ, Compatible Firmware Versions

Scope Rider answers to a IP address which has not been entered

Scope Rider answers to a IP address which has not been entered.

AMS32 Signal Path Calibration, ensure that valid CAL Data are loaded on the OTA Network Analyzer

FAQ AMS32 Signal Path Calibration, ensure that valid CAL Data are loaded on the OTA Network Analyzer

EMC32-E+: Check EMC32 Expansions

FAQ: Check EMC32 Expansions

Set 10:2:2 format for special slot in 5G

How can I set the special slot format in 5G NR measurement application for TDD?

NRP-Z Sensors only responding in VISA, not in Application

Unfortunately I can control my NRP-Z sensor only from the VisaTester but not from my Python IDE when using the same Device Identifier "USB::0x0aad::0x0023::102800::INSTR". What is wrong?

Verification of FM Chirps using R&S Pulse Sequencer software and Transient Analysis Spectrum Analyzer Option K60

This summary intends to give a fast overview for generation and verification of FM chirp signals using R&S Instruments and software Tools.

Remote control via drivers: How to set the ports in RSZVB_Select_Calibration_Type

I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?

VNA calibration warning that the active cal kit does not contain all needed standards

Active cal kit or cal unit does not contain all standards needed for selected cal procedure.

Scope Rider RTH: How to query when a trigger occured?

No synchronisation in Auto Trigger Mode

RTB/RTM/RTA - reduce Stop Frequency at FFT

How to generate separate graphics for the horizontal and vertical result using EMC32-EB