Integrated end-to-end data solution with IP traffic analysis and protocol statistics allows detailed analysis of data traffic generated by IoT and mobile devices.

06-Jun-2017

Frequency Response Compensation for SMx Generator Series

27-Oct-2009 | AN-No. 1MA56

Transfer of Trace Data from R&S Network Analyzer ZVx to Microsoft Excel

22-Mar-2007 | AN-No. RSI02

Generating 3GPP Multi Carrier Signals for Amplifier Tests with R&S SMIQ03HD and WinIQSIM™

02-Sep-2002 | AN-No. 1GP52

Power and Modulation Measurements on VHF Transmitters Example: Rohde & Schwarz VHF-FM Transmitter SU115

04-Jun-1998 | AN-No. 1EF09

Vector Network Analyzers of t ZNA and ZNB family are able to measure magnitude and phase of complex S-parameters of a device under test (DUT) in the frequency domain.

30-Jul-2020 | AN-No. 1EP83

This document describes Bluetooth Low Energy RF over-the-air RX and TX measurements using advertising channels for communication with Bluetooth Low Energy devices.

14-Dec-2020 | AN-No. 1C109

Rohde & Schwarz offers a flexible test solution for the high demands of R&D and highthroughput production environments.

21-Mar-2017

The R&S®NGL200 and R&S®NGM200 can simulate battery cells when testing battery management systems and replace far more expensive dedicated battery simulators.

08-Jun-2020

Read this application card to learn more about what the 10BASE-T1S Ethernet compliance test offers and how it ensures reliable operation and functionality.

15-May-2020

The R&S®RT-ZPR20 and R&S®RT-ZPR40 power rail probes with a 1:1 attenuation ratio have very little noise and sufficient bandwidth to not attenuate critical signal content.

17-Jul-2018

A time-gated spectrum scan applies a time gate on uplink/downlink slots/symbols or guard period and helps identifying interference in operational 5G TDD networks.

21-Sep-2023 | AN-No. 8NT08

Mobile Tests for GSM under Fading Conditions

23-May-2000 | AN-No. 1MA19

Generation of Test Signals acc. ISO 14708 for Testing of Cardiac Pacemakers

15-Jul-2009 | AN-No. RCS0812-0065

The R&S®CMP200 radio communication tester together with the R&S®CM-Z300A time of flight kit provides an accurate setup for time of flight measurements – in validation, calibration and certification.

27-Jul-2022

HSDPA - Challenges for UE Power Amplifier Design

11-Jul-2011 | AN-No. 1MA84

This application Note is based on CMW500, SMBV100B and Vector CANoe.Car2x Software and guides to how to simulate the specific Cellular Vehicle-to-Everything (C-V2X) wireless environment in respect to road transport scenarios and transmitted messages around the Device Under Test (DUT) like a Telematics Control Unit (TCU). It shows how to verify and validate the C-V2X application of the DUT in laboratory environment. The virtual simulation scenario is not limited to the requirements of CSAE53-2017 specification, and it could be modified by user according to this operating guide with CANoe.Vehicle-to-everything (V2X) is a new generation of information and communications technologies that connect vehicles to everything. The objective of V2X is to increase road safety and manage traffic efficiently.C-V2X is designed to offer low-latency vehicle-to-vehicle (V2V), vehicle-to-roadside infrastructure (V2I) and vehicle-to-pedestrian (V2P) communications services to add a new dimension to future advanced driver assistance systems (ADAS). C-V2X as one communications standard defined by 3GPP in Release 14 uses LTE technology as the physical interface for communications. The standard describes two types of communications. The vehicle-to-network (V2N) communications type, exploits the cellular Uu interface, uses traditional cellular link to enable cloud services to be integrated into end-to-end solutions, e.g. to allow road and traffic information for a given area to be distributed to the vehicles.The second type is referred to as direct or PC5/Sidelink (V2V, V2I, V2P) communications, where data transmission takes place over the PC5 interface. In that type, C-V2X does not necessarily require a cellular network infrastructure. It can operate without a SIM and without network assistance and uses GNSS as its primary source for time synchronization.Verifying system functionality and performance exclusively by field testing in a real-world environment can be time-consuming, costly and very challenging. Requirements regarding functionality, and consequently the required assistance functions, are constantly changing. Due to this fact, test solutions are needed during the development and introduction phase to verify compliance with the standards. The PC5 direct communications type allows exchange of time sensitive and safety relevant information. Using a mobile communication tester like the R&S® CMW500 together with a C-V2X scenario simulation tool delivers reproducible test scenarios. This is essential for the standardization of verification processes for C-V2X in order to obtain reliable and comparable results, and it helps to demonstrate that end-to-end functionality between two C-V2X devices from different vendors works properly.

02-Jun-2021 | AN-No. GFM341

This document provides some technical background and guidance on how to optimize the measurement of one of the key performance parameters of WLAN transmitters - the Error Vector Magnitude (EVM).

This application note provides some technical background on how to optimize the measurement of one of the key performance parametersof 802.11be WLAN transmitters.

06-Sep-2022 | AN-No. 1EF114

Welcome to our short video tutorials on how to test radars using Rohde & Schwarz test equipment. Access to most information about radar is pretty restricted, as many radar applications are military or secretive industrial research.

03-Feb-2014 | AN-No. 1MA209

Rohde & Schwarz solution CERTIUM VCS

24-Jul-2023

Setting up complex real-time trigger conditions using the R&S®RTE and R&S®RTO oscilloscopes increases the test coverage and robustness of converter and inverter systems.

10-Aug-2020

S-Parameters of a 50 to 75 Ohm impedance matching device using R&S ZVx VNA

06-May-2009 | AN-No. 1EZ59

This application note describes ATSC Mobile DTV standard A/153, ATSC-M/H. This standard is completely implemented in the R&S AEM100 ATSC-M/H Emission Multiplexer.

22-Jan-2011 | AN-No. 7EB01

This application note will focus on phase noise measurements for pulsed RF carriers such as those used for radar systems.

18-May-2016 | AN-No. 1EF94

Testing LTE MIMO Signals using a R&S RTO Oscilloscope

24-Apr-2013 | AN-No. 1EF86

With the R&S ® Pulse Sequencer software - Revolutionized pulsed signal generation: easy, intuitive, powerful - , engineers now have a single software tool to define pulsed signals for different levels of complexity.

27-Jul-2017

Load transient response – enhancing loop stability testing

09-May-2023

All electronic devices contain capacitive or inductive components that can cause a disproportionately high current while switching on the device.

09-Oct-2018

This application note provides and overview of the technology, the details of the standard and summarizes the R&S®TSMx scanner features for LTE-M measurements.

26-Jul-2019 | AN-No. 8NT04

Controlling External Generators and Power Meters with Network Analyzer ZVR

19-Oct-1998 | AN-No. 1EZ46