Introduction to the fundamentals of programming the R&S Smart Instruments Family 300 in different developement environments.

25-Jun-2007 | AN-No. 1MA73

Digital pre-distortion (DPD) is a common method to linearize the output signal of a power amplifier (PA), which is being operated in its non-linear operating range.The R&S K18D application family offers a very easy-to-use method to pre-distort amplifiers without modelling the DUT.However, many engineers in PA design request a simple and easy-to-use tool that delivers a DPD model applicable to any real-world signal.This application note with the accompanying software tool allows engineers without in-depth knowledge of DPD or remote programming to generate a DPD model and verify it against the DUT, based on the results of the K18D application.

25-Mar-2019 | AN-No. 1EF105

Some of the new Rohde & Schwarz instruments, such as the R&S®OSP and R&S®FSC, only have a LAN interface. To be able to operate these instruments in a purely GPIB system, a converter must be connected between the instrument and the GPIB. Rohde & Schwarz now offers such a GPIB to LAN converter.

03-Aug-2010 | AN-No. 1SP30

Rapid and accurate verification of beamforming weights is required for example, for codebook generation or beamforming algorithm development or verification. This document describes the unique application of Rohde & Schwarz VNA (Vector Network Analyzers) to fully characterize the passive part of multi-element antennas intended for beamforming.A range of R&S VNA models are optionally equipped with multiple independent sources, whose relative amplitude and phase may be arbitrarily controlled ("defined coherence mode"), in addition to frequency and true time delay. These sources may be connected to individual elements of a multi-element antenna to derive and verify transmit (Tx) mode beamsteering and beamforming operation.The R&S®ZVA in "Defined Coherence Mode" can electronically be switched to / from the conventional S-parameter mode. Therefore, Sparameter and beamforming measurements may be performed efficiently within a single connection cycle of the antenna.Multiple VNA may be daisy-chained, to extend the concept shown to support an arbitrary number of ports.The R&S®Quickstep sequencing software may be downloaded from:https://www.rohde-schwarz.com/software/quickstep/

20-Mar-2017 | AN-No. 1MA278

- not available -

20-Jul-2001 | AN-No. 7BM10

The R&S®QPS millimeterwave security scanner delivers the most accurate measurement results in 1.5 to 2.5 s. The instantaneous scan requires only 64 ms, or five times faster than the blink of an eye, virtually eliminating the ambiguous readings that occur due to accidental movement with the longer scan time of other imaging technology.

22-Jan-2019

The new buffer analysis feature was introduced with firmware version 2.80 for the R&S DVM family. This application note describes this feature and explains how it represents a valuable asset to your daily business operations This application note first provides background information and then explains how monitoring and measurement have been implemented in the R&S DVM family.

23-Mar-2006 | AN-No. 7BM53

3GPP TS36.141 defines conformance tests for EUTRA base stations (eNodeB). Release 14 (LTEAdvanced Pro) added several tests, such as those for enhanced Licensed Assisted Access (eLAA).This application note describes how all required performance tests (TS36.141 Chapter 8) can be performed quickly and easily by using vector signal generators from Rohde & Schwarz.Examples illustrate the manual operation. A free software program enables and demonstrates remote operation.The LTE base station transmitter (Tx) tests (TS36.141 Chapter 6) are described in Application Note 1MA154.The LTE base station receiver (Rx) tests (TS36.141 Chapter 7) are described in Application Note 1MA195.

11-May-2016 | AN-No. 1MA162

RF performance measurements for Wi-Fi 7.

30-May-2022

CST® Filter Designer 3D, which is part of the CST Studio Suite® simulation software from Dassault Systèmes, is a complete synthesis tool for filters and diplexers. It provides a range of solutions throughout the design process of coupled resonator filters and even beyond with its VNA based tuning capability. CST Filter Designer 3D assists in tuning filter hardware, significantly reducing the time for optimizing a device to meet the expected specifications. An attractive instrument to obtain fast data reading for realtime filter tuning is the R&S®ZNB vector network analyzer from Rohde & Schwarz.

27-Nov-2019

Simultaneous DL throughput verification and UL transmission testing with the R&S®CMW500

29-Jul-2009

With the extension of the 3GPP FDD system to include HSDPA, the HS-DPCCH has been added as a new code channel in the uplink. This Application Note describes the transmitter measurements provided by the CMU200 to perform the transmitter measurements defined in TS 34.121 in presence of the HS-DPCCH. CMU200 receiver measurements according to TS 34.121 that measure the throughput and the CQI reporting are described. Subject to change – T. Braun, November 2005 - 1CM62

25-Nov-2005 | AN-No. 1CM62

Rohde & Schwarz recognizes the potential risk of computer virus infection when connecting Windows®-based test instrumentation to other computers via local area networks (LANs), or using removable storage devices. This white paper introduces measures to minimize malware threats and discusses ways to mitigate risks while insuring that instrument performance is not compromised. The paper discusses the use of anti-virus software, with recommended configuration settings. It also outlines how to keep the Windows® XP operating system properly updated through regular installation of OS patches.

04-Oct-2012 | AN-No. 1EF73

An automated test solution based on the R&S®CMW wideband radio communication tester fully supports the new test cases for real-time submeter positioning.

10-Jun-2022

Generation of wideband digital modulated signals in V-band and above is a challenging task and typically requires a set of multiple instruments. This application note aims at simplifying the task and looks into the analysis part as well. Latest signal and spectrum analyzers like the R&S®FSW67 and R&S®FSW85 are first to allow use in V-band up to 67 GHz and E-band up to 85 GHz respectively without external frequency conversion. Up to 8.3 GHz of modulation bandwidth can be covered using the R&S®FSW-B8001 option. Millimeter wave use of analyzers ranging from 26 GHz up is shown. Application note 1MA217 describes V-band signal generation and analysis up to 500 MHz modulation bandwidth. This application note expands modulation bandwidth up to 2 GHz and covers both V- and E-band examples.

18-Jun-2015 | AN-No. 1MA257

Propagation measurements are indispensable in the planning of digital, cellular mobile radio net-works. To find the optimum sites for the base stations, a mobile test transmitter system simulating the base station is operated from a number of possible locations. The test receiver system is accommodated in a vehicle, which is driven along a test route to perform measurements. The parameters measured, such as level, bit error rate or channel impulse response, provide information on the coverage within the cell. The main problem is to minimize interference caused by multipath propagation in the reception area. The SME offered by Rohde & Schwarz is a universal test generator that can be used as the core of a test transmitter system. The SME generates the GMSK-modulated signals required for GSM propagation measurements in line with the rele-vant standards. Thanks to its low weight of 17 kg it can be carried even to remote sites. Fitted with the new optional DM Memory Extension (SME-B12, in the following referred to as XMEM), the SME is able to store data sequences of up to 8 Mbit which are long enough for receiver measurements with test mobile stations. A suitable test receiver system is for instance a test mobile station for measuring level and bit error rate and the Impulse Response Analyzer PCS from Rohde & Schwarz for measuring the channel impulse response. The present Application Note describes how the XMEM can be loaded with suitable data (test sequence) by the GSM Radiocommunication Test Set CRTP from Rohde & Schwarz and how the SME has to be adjusted for GMSK modulation of these data. First, however, an overview is given of all functions of the XMEM and their operation supplementary to the Operating Manual. Finally, it is explained how the XMEM data can be transferred between PC and SME via the IEEE-488 or RS-232 interface.

01-Jul-1999 | AN-No. 1GPAN14

Testing the tolerance to phase and impulsive noise is an integral part of quality tests for DVB-T/H and ATSC (8VSB) receivers, and several national and international standards specify guidelines and minimum requirements in this context. This Application Note introduces the R&S SFU-K42 impulsive noise option, the R&S SFU-K41 phase noise option, as well as the R&S SFU-K43 multinoise use option and describes how these can be used for testing the tolerance to phase and impulsive noise on commercial receivers.

26-Jan-2007 | AN-No. 7BM64

Rohde & Schwarz mobile network testing solutions enable operators to efficiently increase network capacity via hardware-related, capacity-enhancing features such as antenna tilt optimization, carrier aggregation, 4x4 MIMO and 6-sector sites.

09-Aug-2016

Communication systems according to IS-136 (NADC) use Time Division Multiplex Access (TDMA) for the communication between base station and mobile stations. There are 6 time slots available. Depending on the amount of data, which have to be transmitted, the system uses full rate channels or half rate channels. A full rate channel means, that the mobile is accessed every 3rd time slot (e.g time slot 1 and 3, time slot 2 and 4 or time slot 3 and 6). With half rate channels the mobile is accessed every 6th time slot. Full rate and half rate channels may be mixed on demand. The base stations transmit continous on their frequency. Depending on the used combination of full rate and half rate channels the base station uses a different sequence of synchronisation words. The mobile stations use bursted transmission with one of the synchronisation words S1 to S6 defined in the standard. Signal Generator SME is excellently suited to generate these signals to test either base station receivers or mobile phone receivers. Together with the modulation data supplied with this application note the SME serves as a signal source for various test and measurement applications in the whole frequency range of IS-136 (NADC).

01-Jul-1999 | AN-No. 1GPAN35

Signal faults and anomalies can cause electrical and electronic systems to fail. Especially in the field, these errors can lead to system downtimes and produce high costs. Consequently, finding them quickly and efficiently as well as identifying their source are crucial.

30-Dec-2015

Despite the now standard digital distribution of video signals, analog video signals are still an integral part of AV terminals in the home. This application note covers the fundamentals of analog component signals and shows how the signal quality can be measured with the measuring equipment from Rohde & Schwarz.

28-May-2015 | AN-No. 7MH107

The R&S WiMAX application firmware R&S FSx-K93 calculates several different power parameters. This application note describes the basic power measurements of WiMAX OFDMA signals and gives an overview of the calculation of the different values.

11-Jul-2007 | AN-No. 1EF60

This application note provides information about the spurious emission measurement on 3 GPP base station transmitters. The basic requirements and the limiting factors of a spectrum analyzer are explained in detail. Dynamic range calculations with measurement examples show the practical realisation of spurious emission measurements.

10-Jan-2002 | AN-No. 1EF45

This application note describes the general setup and required equipment for EMC measurements according to the EMS standard IEC / EN 61000-4-6.

29-Mar-2007 | AN-No. 1SP31

This application note describes the basic frequency filter measurements that are often required during service repairs, during development of simple circuits and for training purposes. These measurements do not always require high-end T&M equipment. Instruments in this class typically offer a very wide range of measurement functions coupled with the best-possible RF performance. However, these features are not necessary for simple applications. This application note therefore describes measurements using instruments from the cost-effective Rohde & Schwarz Value Instruments series. The instruments in this series offer the measurement accuracy demanded by quality-conscious users plus easy operation and all of the functionality needed for everyday measurement tasks.

27-Mar-2015 | AN-No. 1MA243

A high frequency transformer is a key component when designing isolated switching mode power supplies (SMPS). Leakage inductance is essential in the control of many design parameters including efficiency, maximum voltage rating for switching elements and EMI when it comes to designs using customized transformers. Accurate measurement of this parasitic element is mandatory. The R&S®LCX LCR meter is ideal for this challenging measurement task.

15-Feb-2022

Unique automatic level controlled (ALC) based test setup using the R&S®ZVA vector network analyzer and R&S®BBA150 broadband amplifiers provides highly accurate and reproducible results in minimum test time.

27-Sep-2013

3GPP TS36.141 defines conformance tests for EUTRA base stations (eNodeB). Release 14 added several tests, especially for enhanced License Assisted Access (eLAA).This application note describes how all required receiver (Rx) tests (TS36.141 Chapter 7) can be performed quickly and easily by using vector signal generators from Rohde & Schwarz. A few tests additionally require spectrum analyzers from Rohde & Schwarz.Examples illustrate the manual operation. A free software program enables and demonstrates remote operation.The LTE base station transmitter (Tx) tests (TS36.141 Chapter 6) are described in Application Note 1MA154.The LTE base station performance (Px) tests (TS36.141 Chapter 8) are described in Application Note 1MA162.

11-May-2016 | AN-No. 1MA195

7BM30 Digital TV,DTV,DVB,MPEG2,Broadcasting,Television,SFQ,EFA Phase Jitter in DTV Signals Phase Jitter in DTV Signals 7BM30 Digital TV,DTV,DVB,MPEG2,Broadcasting,Television,SFQ,EFA Phase Jitter in DTV Signals

16-May-2002 | AN-No. 7BM30

The R&S CMU300 combines high-precision Node B parameter tests with layer 1 signalling processes for the first time. Thus, you can now test Node Bs under more realistic conditions as it was possible with existing concepts. This document describes the new measurement functions and provides an overview of their applications.

10-Nov-2005 | AN-No. 1CM58