Rohde & Schwarz mobile network testing solutions enable operators to efficiently increase network capacity via hardware-related, capacity-enhancing features such as antenna tilt optimization, carrier aggregation, 4x4 MIMO and 6-sector sites.

09-Aug-2016

Signal faults and anomalies can cause electrical and electronic systems to fail. Especially in the field, these errors can lead to system downtimes and produce high costs. Consequently, finding them quickly and efficiently as well as identifying their source are crucial.

30-Dec-2015

SMIQ/ABFS TV shows the SMIQ or ABFS display remotely on any Windows™ PC

02-May-2002 | AN-No. 1GP54

Communication systems according to IS-136 (NADC) use Time Division Multiplex Access (TDMA) for the communication between base station and mobile stations. There are 6 time slots available. Depending on the amount of data, which have to be transmitted, the system uses full rate channels or half rate channels. A full rate channel means, that the mobile is accessed every 3rd time slot (e.g time slot 1 and 3, time slot 2 and 4 or time slot 3 and 6). With half rate channels the mobile is accessed every 6th time slot. Full rate and half rate channels may be mixed on demand. The base stations transmit continous on their frequency. Depending on the used combination of full rate and half rate channels the base station uses a different sequence of synchronisation words. The mobile stations use bursted transmission with one of the synchronisation words S1 to S6 defined in the standard. Signal Generator SME is excellently suited to generate these signals to test either base station receivers or mobile phone receivers. Together with the modulation data supplied with this application note the SME serves as a signal source for various test and measurement applications in the whole frequency range of IS-136 (NADC).

01-Jul-1999 | AN-No. 1GPAN35

Despite the now standard digital distribution of video signals, analog video signals are still an integral part of AV terminals in the home. This application note covers the fundamentals of analog component signals and shows how the signal quality can be measured with the measuring equipment from Rohde & Schwarz.

28-May-2015 | AN-No. 7MH107

The R&S WiMAX application firmware R&S FSx-K93 calculates several different power parameters. This application note describes the basic power measurements of WiMAX OFDMA signals and gives an overview of the calculation of the different values.

11-Jul-2007 | AN-No. 1EF60

FMCW radar sensors are used in vehicles for adaptive cruise control and for blind-spot, lane-change and cross traffic assistants. Radar sensors for acquisition of the surroundings are key components for future vehicles with semi-autonomous and fully autonomous driving. Autonomous driving requires radars that reliably detect objects in the surrounding area. Radar makes it possible to quickly and precisely measure the radial velocity, range and azimuth and elevation angle of multiple objects. For this reason, the automobile industry is increasingly using this technology in advanced driver assistance systems (ADAS). Rohde & Schwarz offers T&M solutions for generating, measuring and analyzing radar signals and components to ensure trouble free operation of these sensors. The high-performance oscilloscope R&S® RTP with four measurement channels is the perfect solution for multi-channel measurements on MIMO radar sensors and correlation with other signals e.g. power rails, whereas a spectrum analyzer such as the R&S® FSW85 offers highest dynamic up to 85 GHz.This application note focuses on how to measure and analyze FMCW radar signals with up to 6 GHz bandwidth with an R&S® RTP oscilloscope. On-board analysis features for pulse and chirp analysis for single- and multi-channel measurements will be addressed as well as the combination of oscilloscope and R&S® VSE software. Measurement of an FMCW radar signal in the 77 - 81GHz band with 4 GHz bandwidth is demonstrated.

07-Aug-2019 | AN-No. GFM318

This application note describes the suitability of the R&S®ZVM and R&S®ZVK as multichannel microwave receivers for antenna measurements and RCS measurements including measurements on pulsed signals. Application examples describe the measurement possibilities on pulsed signals using the R&S®ZVM/ZVK as stand-alone units. In addition, various R&S®ZVM/ZVK-based antenna measurement systems of the March Microwave company are presented in detail.

10-Sep-2004 | AN-No. 1EZ52

This application note describes how to connect R&S® test and measurement products quickly and seamlessly to AWR® Visual System Simulator™ (VSS) via a GPIB or LAN interface. Using AWR® Connected™ customized for Rohde & Schwarz hardware and R&S® WinIQSIM2™ signal simulation software, the flexibility of digital radio standards is highlighted and its integration into VSS is demonstrated.

20-May-2010 | AN-No. 1MA174

R&S®NESTOR cellular network analysis software supports law enforcement agencies in alibi verification by analyzing mobile network traces. R&S®NESTOR gives users reliable confirmation of whether an individual’s mobile phone was at a specific location at the time of a crime.

10-Apr-2024

7BM30 Digital TV,DTV,DVB,MPEG2,Broadcasting,Television,SFQ,EFA Phase Jitter in DTV Signals Phase Jitter in DTV Signals 7BM30 Digital TV,DTV,DVB,MPEG2,Broadcasting,Television,SFQ,EFA Phase Jitter in DTV Signals

16-May-2002 | AN-No. 7BM30

The R&S CMU300 combines high-precision Node B parameter tests with layer 1 signalling processes for the first time. Thus, you can now test Node Bs under more realistic conditions as it was possible with existing concepts. This document describes the new measurement functions and provides an overview of their applications.

10-Nov-2005 | AN-No. 1CM58

Designing and implementing an active phased array antenna requires precise characterization of individual components and the integrated performance of the array. To ensure an accurate test of the intended adaptive nature of the active phased array antenna, the embedded algorithms need to be tested as well.This application note aims to explain test procedures and give recommendations towards characterization of the relevant parameters for active phased array antennas and their passive subsystem, as often used in applications for Mobile Communication and RADAR. This application note describes transmit signal quality testing, multi-element amplitude and phase measurement techniques both in receive and transmit cases and introduces a new automated test methodology antenna radiation pattern measurement over frequency. This paper also describes the test system used for transmit and receive module (TRM) characterization in active array antennas.

04-Jul-2016 | AN-No. 1MA248

An offline AC/DC switching converter has no separate bias power supply that provides power to the control integrated circuit itself. Here, an auxiliary primary winding and discrete components are added to supply power to the control circuit. Verifying this circuitry is essential and requires accurate and detailed signal level and timing measurements. The startup sequence takes a long time, which needs to be taken into consideration in the measurement and requires an instrument with sufficient memory.

23-Nov-2022

In an ideal scenario, a probe accurately transmits a signal from the device under test (DUT) in its original form with no alterations. Differential probes are designed to eliminate common-mode (CM) distortion by cancelling out identical signal artifacts on each socket relative to earth. In practice, issues such as poor CM rejection, frequency response degradation and signal distortion can compromise signal integrity, particularly in high-speed power applications where signal fidelity is crucial.

25-Nov-2024

The R&S®SMBV100B signal generator offers a remote emulation feature that makes it possible to control the instrument by commands other than the built-in native SCPI commands. This feature allows the user to replace signal generators, e.g. from other manufacturers, with the R&S®SMBV100B without having to change the remote control code.This application note describes how to use the remote emulation feature in general. Furthermore, it describes in detail the remote emulation for each supported instrument, limitations of the individual emulations and the remaining differences between the emulated and the original commands.

30-Sep-2019 | AN-No. 1GP121

The R&S®QPS quick personnel security scanners are new, high-resolution security scanners designed specifically to make people screening at security checkpoints faster, more effective and comfortable.

23-Jan-2019

RF system noise contributions define receiver capabilities and sensitivity. The noise figure measures how the critical components affect the signal.

28-Jan-2022

The topic of this application note is mobile phone measurements – in theory and in practice. It discusses measurements according to the most common standard in use today, GSM.The first, theoretical portion of this application note covers digital modulation and access methods in general. This is followed by an overview of the specific characteristics of the GSM standard as well as a summary of the most important mobile radio measurements.The second, practical portion of this application note covers some of these measurements in detail and runs through them step by step. These measurements can be performed by small groups in labs.The measurements and analysis of the results are intended to illustrate the theoretical portion of the application note and to deepen the reader's understanding.All measurements are performed using the R&S®CMW500 wideband radio communication tester and an off the shelf mobile phone.

22-Aug-2014 | AN-No. 1MA231

Short measurement time in conjunction with high accuracy and repeatability of results are essential for efficient testing of mobile phone power amplifiers. Power Meter R&S®NRP, Signal Generator R&S®SMIQ, Spectrum Analyzers R&S®FSP/FSU/FSQ and Power Supply R&S®NGMO2 offer optimum characteristics such as high accuracy, fast settling speed and short measurement time in programmed mode. This application note concentrates on testing GSM/EDGE mobile power amplifiers and shows typical test setups and programming examples for Signal Generator R&S®SMIQ and Spectrum Analyzer R&S®FSP/FSU/FSQ, benchmark numbers and repeatability results.

29-Apr-2004 | AN-No. 1MA66

Integrated sensing and communication (ISAC) is a pillar of 6G. Combining two different yet similar worlds – communications and environmental sensing – brings the future to life in the 6G era. The key ISAC drivers are beamforming with MIMO arrays, artificial intelligence (AI), modern modulation schemes and dense network infrastructure. The R&S®AREG800A automotive radar echo generator is a core element of a versatile research and development test solution in the ISAC community.

11-Mar-2024

Multichannel signal reception in parallel using digital downconverters in a monitoring receiver.

14-May-2014

Most of the tests specified in standard TS 34.121 for 3GPP Rel-99 can be performed with R&S®CMU200. This document provides a step by step guide on how to perform Rel-99 measurements on transmitter/receiver characteristics, and performance tests according to TS 34.121 V8.4.0 clauses 5, 6 and 7 with standalone R&S®CMU200. Test cases that require additional instuments e.g. fading simulator (R&S®SMU200A or R&S®AMU200A) or spectrum analyzer (R&S®FSQ) will be discussed in brief in this application note with recommended reference. A set of *.sav files based on R&SCMU200 firmware V5.02 for UE supporting band I with power class 3 in RMC 12.2 kbps downlink/uplink is attached to this application note.

15-Apr-2009 | AN-No. 1CM71

RF interference is one of the largest contributors to poor network performance. It shows up in dropped calls and low data throughput rates. Traditionally, interference hunting means you get a list of sites with bad performance from an OSS. This defines the areas for interference hunting quite well.If, however, the problem remains after attempts at mitigation, it could be because other sources often mask symptoms of RF interference. Usually the strongest masking is due to the overlap between the interference signal and your network's signals. Analysis could involve complete cities or even countries, an error-prone task when using traditional spectrum analyzers and/or portable receivers and one that consumes a significant amount of time and budget.A more automated solution for larger areas can make the effort involved more manageable. The Rohde & Schwarz network scanner family (R&S®TSME, R&S®TSMA and R&S®TSMW) plus the network problem analyzer (NPA) feature of the R&S®ROMES4 measurement software is such a solution. It allows you to perform a fast drive test with a fleet of cars and collect spectrum data for your targeted or even complete network area in next to no time. Back at your office, the NPA tells you where to send dedicated interference hunting teams with an analyzer or receiver to track down the source of interference. This paper introduces the approach in detail.

02-Oct-2017 | AN-No. 1MA293

This paper describes the characterization of aluminum electrolytic capacitors specifically used in AC-DC power converter applications. It will be discussed why this capacitor technology is critical regarding lifetime and why it cannot be substituted simply by any another capacitor technology. Different aging effects of the capacitor will be discussed. Usage of the capacitor in different AC-DC converter topologies will be presented. Simulation circuits will be used to analyze the capacitor in more detail before suitable measurements will be performed to demonstrate a real example of a switching-mode power supply (SMPS).After the introduction into the aluminum electrolytic capacitor basics and theory, this paper will also present all important and possible measurements of capacitor parameters, like capacitance, equivalent series resistance (ESR) and ripple current. This includes in-circuit measurement which can be performed with an oscilloscope. An LCR-bridge is used to obtain high accuracy measurements in addition. A comparison between the two measurement methods will be presented. Furthermore, the required measurement hardware for the in-circuit measurements and the bridge measurement will be discussed and presented.Lastly, two different lifetime calculation methods are presented and a real example is used to compare the advantages and disadvantages of the different methods.Thanks to Mr. Frank Puhane from Würth eiSos GmbH & Co. KG who provided me with all aluminum electrolytic capacitor samples including the prepared capacitor with build-in temperature sensors to perform all measurements. Furthermore, his great expertise was very beneficial and helpful to create this premium application note.

07-Feb-2023 | AN-No. 1SL388

Measurement uncertainties that occur when the R&S FSMR measuring receiver is used to calibrate RF levels are described and quantified in this application note. Several Excel spreadsheets are included. They can be used to simplify calculation of the uncertainty for various configurations.

28-Mar-2006 | AN-No. 1MA92

The R&S CMW500/270 can generate and measure standard-compliant WLAN IEEE 802.11ac signals with bandwidths from 20 MHz up to 160 MHz.This document explains the CMW solution for the signals with 160 MHz bandwidth and describes the required configurations step by step.

21-Oct-2013 | AN-No. 1CM101

For measurement settings below 10 mV/div, oscilloscopes typically reduce the measurement bandwidth in order to keep the trace noise as low as possible. The R&S®RTO is different: It offers the full bandwidth even for the most sensitive settings, and an A/D converter with more than 7 effective bits (ENOB) digitizes the signal.

13-Jul-2012

Solutions and Tipps for NR FR1 in TDD Downlink Mode

5G New Radio (NR) is a radio technology specified by 3GPP and was first released in 3GPP release 15. It is designed to target three use cases, i.e. enhanced mobile broadband (eMBB), massive machine type communication (mMTC) and ultra-reliable low latency communication (URLLC). Among these three use cases, eMBB represents actually a further evolution of mobile broadband communication from LTE standard. According to the technical performance requirement defined by IMT-2020, by deploying 5G technology, peak data rates of eMBB application are expected to reach 20 Gbps in downlink (DL) and 10 Gbps in uplink (UL) direction, respectively. Typical use cases of eMBB are data hungry applications, such as high resolution 8K video streaming, virtual reality (VR), augmented reality (AR) etc.Verification of a 5G capable user equipment (UE) with respect to its achievable maximum data throughput under controllable and deterministic test conditions is an essential process during the design phase of the product. Performance centric verification through identification of the data throughput bottleneck, product benchmarking against a golden device enhances tremendously the user experience in the end.This document focuses on 5G NR frequency range 1 (FR1) with TDD duplex mode in E-UTRAN New-radio Dual Connectivity (ENDC) operating mode. As 5G NR physical layer offers a plethora of flexibility, the motivation here is to provide a kind of guideline of relevant parameter settings to stimulate device under test (DUT)'s max throughput capacity. The status quo of the R&S solutions at the time when the application note is created are described. Shown feature sets are constantly evolving, so the screenshots used and the parameters shown may change.

07-Jul-2022 | AN-No. 1SL379

The following application note describes the function and operation of user menus for FSE Spectrum Analyzers including option Vector Signal Analysis (FSE-B7). For measurements according to the PCS 1900 standard for Mobile Stations user menus are provided, which perform settings on FSE for the different measurements required in the standard. The menu and the accompanying setups are stored on a floppy disk.

01-Nov-1996 | AN-No. 1EF22