This application note describes methods using an R&S®ZVA network analyzer, one or two R&S®SMB100A signal generators and an R&S®FSW signal analyzer to accurately measure all the key parameters of frequency converters with embedded local oscillator. A commercial satellite up-converter is used as a device under test example.

30-Apr-2015 | AN-No. 1MA224

Soft-start verification is becoming a major concern for modern switching mode power supplies due to the increasing use of digital controllers. The R&S®RTM3000 and R&S®RTA4000 oscilloscopes offer pulse width modulation (PWM) track analysis functionality, which is a great feature for verifying and optimizing soft start during development.

09-Jul-2019

Interferences on audio transmissions, which happens only from time to time, are very difficult to be measured. This application note describes a method, used by the audio analyzers UPL and UPD, to monitor test tones without any interruption and detecting even the shortest clicks.

04-Jun-1998 | AN-No. 1GA31

Synthetic aperture radar (SAR) uses radar wavelengths for airborne or spaceborne ground mapping. The resolution of the SAR ground map depends on the range and cross-range SAR processing resolution. Cross-range resolution is determined by integrating pulses along a flight path for a period of time to create a synthetic aperture. Longer synthetic apertures result in finer cross-range resolution. Range resolution is achieved by radar waveform bandwidth in the form of a linear frequency modulated (LFM) chirp. Wider bandwidth enables finer range resolution.

16-Apr-2021

This application note describes how to use the Rohde & Schwarz software tool ‘RsBatchConvert.exe’ for the conversion of binary data or WinIQSIM generated AMIQ waveforms into the new waveform format. The tool not only rescales I/Q data contained in the file but also changes the K-option requirement from WinIQSIM Kxx to the new WinIQSIM2 K2xx options. Thus, new instruments with installed K2xx options may be used to continue using existing waveform files.

18-Jun-2009 | AN-No. 1GP64

Comprehensive test solutions guide for production and R&D

Small cell is a compact base station with smaller form factor and lower transmission power in comparison to the conventional macro base station. It covers relatively small area and serves less users. Usually, small cell can be integrated into the existing mobile network. By the evolution of radio access technology, the role of small cell has been changing through the evolution path. In the 2G/3G time, its role was to provide coverage in corner cases. Later during LTE, networks are not just providing coverage but capacity too. Small cells were then used to provide the addition capacity where required without adding additional spectrum. Now in 5G era, network operators use densification as an important strategy to provide seamless 5G services which demand coverage, capacity and performance too. With use cases requiring the 5G millimeter wave (mmW) rollouts, it makes sense to use small cells for densification due to the propagation characteristics of mmW.In this application note, we will shed light on the testing aspects of a small cell throughout the product life cycle with particular focus on the production test solution for the small cell device under test (DUT) in FR2 (frequency range 2, mmW frequency band) in Over the Air (OTA) environment for option 6 split based on radio communication tester R&S®CMP200 and OTA chamber R&S®CMQ200. The document is complemented with more insights into test solutions used in typical R&D test applications towards the second half of the application note.

19-Jun-2023 | AN-No. 1SL395

When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers ensure the receiver functionality, this functionality must be tested when the receiver is integrated into the car. When it comes to testing analog and digital TV and audio broadcast receivers in cars, special requirements must be met. Although suppliers guarantee the receiver functionality, this functionality must be tested when the receiver is integrated into the car.

19-Feb-2015

For conducted immunity tests, EMC labs require a test signal source driven at high RF powers and at defined frequencies. Rohde&Schwarz offers a compact solution with a signal generator, an RF solid-state amplifier with power up to 350 W, power sensors and test software for the frequency range from 4 kHz to 400 MHz.

03-Dec-2021

With AMPTUNE amplifier nonlinearity can be measured with signals that are typical for the signals encountered by the amplifier in day-to-day use. The measurement can be checked by pre-distorting the control signal. Also, the results can be automatically stored for further processing with external programs.

26-Oct-2005 | AN-No. 1MA27

Rohde & Schwarz recognizes the potential risk of computer virus infection when con-necting Windows®-based test instrumenta-tion to other computers via local area net-works (LANs), or using removable storage devices.This white paper introduces measures to minimize malware threats and discusses ways to mitigate risks while insuring that instrument performance is not compro-mised.The paper discusses the use of anti-virus software. It also outlines how to keep the Windows® 7 operating system properly updated through regular installation of OS patches.

27-Jan-2015 | AN-No. 1DC01

TS-EMF3 TS-EMF TRD Konvertierung (german) TRD Konvertierung (German) TS-EMF3 TS-EMF TRD Konvertierung (german)

11-Nov-2005 | AN-No. TS-EMF3

The R&S®ESW-B8 and R&S®ESW-B8E extended bandwidth options allow the R&S®ESW EMI test receiver to measure with a resolution bandwidth of up to 80 MHz. The increasing number of wideband applications (e.g. radar sensors) and accompanying standards means there is now a greater interest in wide bandwidth measurements.This application note describes the following topics for the R&S®ESW EMI test receiver:► Characteristics and implementation of RF signal paths► Image responses and how their rejection is handled ► Ultrawideband measurement applications as required e.g. by ETSI standards► Solutions for efficiently coping with bandwidth limitations in the range above 8 GHz

19-Nov-2020 | AN-No. 1EE26

Measurement deviations due to systematic errors of a network analysis system can be drastically reduced by an appropriate system error calibration. After system error correction, the residual measurement uncertainties are - besides the stability, linearity, and dynamic range of the network analyzer system - mainly affected by the quality of the calibration standards and the repeatability of the connections. The effective measurement accuracy of the network analysis system can be determined using the results of successive verification measurements utilizing highly precise verification standards.

24-Jan-2001 | AN-No. 1EZ48

High Speed Uplink Packet Access (HSUPA) is a 3GPP release 6 feature for WCDMA. Objective is to achieve uplink data rates of up to 5.76 Mbps and increase throughput and capacity. This application note introduces HSUPA concepts and explains key features.

09-Feb-2006 | AN-No. 1MA94

This Application Note gives a short overview how signals with two different modulation schemes can be analyzed using the R&S®FSW (or R&S®FPS) using its Multi-Standard-Radio-Analyzer (MSRA) and Vector Signal Analysis personality. The Application Note focuses on DVB-S2(X) signals, but the approach may be used for similar signals as well, as e.g. used in microwave backhaul links.The Application Note also provides a software tool that automates the configuration and provides the variety of different constellations that are used within DVB-S2(X).

18-Apr-2016 | AN-No. 1EF93

Spectrum and network analyzers equipped with network interface cards can be integrated in Local Area Networks (LAN). This Application Note describes how to remote control these instruments over a LAN and use VXIpnp instrument drivers over a LAN.

25-Jun-2003 | AN-No. 1EF47

High sampling rate and automatic pulse analysis make the R&S®NRP-Z8x wideband power sensors ideal for time-domain analysis of radar pulses.

06-Aug-2013

This application note addresses the diverse possibilities of interoperability between Rohde & Schwarz power sensors and Rohde & Schwarz signal generators. All current and many legacy Rohde & Schwarz signal generators offer the capability of directly connecting power sensors. This enables power measurements without the need of a base unit or separate PC to display the readings. Furthermore, sensors can be used for special tasks like filling a user correction table or continuously controlling levels at crucial points in the measurement configuration.

31-Aug-2023 | AN-No. 1GP141

broadcasting transmitters, allocated frequencies, monitoring control center, RF power, Automatic monitoring of emission parameters of registered broadcasting transmitters Automatic monitoring of emission parameters of registered broadcasting transmitters broadcasting transmitters, allocated frequencies, monitoring control center, RF power, Automatic monitoring of emission parameters of registered broadcasting

04-Sep-2006

DIRECTV®, a digital TV broadcast system, makes use of transport packets with a length of 130 bytes rather than the more common 188 bytes used in MPEG TS streams. The inputs on the R&S® SFU do not accept transport streams in the DIRECTV® format. This Application Note introduces R&S® DIRECTV tool and explains how it can be used to convert existing 130-byte-based DIRECTV® transport stream content to 188-byte-based ISO 13818-1 streams that are compatible with the R&S® SFU SPI input or the internal R&S® SFU TRP player. This tool is intended for Rohde & Schwarz customers who are licensed to operate an R&S® SFU-K9 DIRECTV coder or R&S® SFU-K108 AMC coder.

05-Oct-2007 | AN-No. 7BM69

The R&S®FSMR3000 (hereinafter FSMR) is a three-in-one instrument incorporating a Measurement Receiver, a Signal and Spectrum Analyser, and a Phase Noise Analyser.This application note demonstrates the use of the FSMR, including the Cross-correlation option (R&S®FSMR3-B60), to measure the Phase Noise characteristics of a raw Signal Generator (R&®SMA100B).The Cross-correlation phase noise measurement improves sensitivity by 5 · log(n) dB, compared with measurements that do not use this option. For example, a measurement using 10 correlations, improves the phase noise floor by 5 dB.

31-Dec-2021 | AN-No. 1SL376

Voice over IP for air traffic control

02-Nov-2011

Rare faults and intermittent signals are difficult to capture. The R&S®RTO Oscilloscope supports the acquisition and the detailed signal analysis of these signals by using the history mode. The history mode allows the user to look back to previous acquisitions and apply the wide set of analysis functions of the RTO. Furthermore it stores the accurate recoding time of the waveforms for subsequent analysis.

03-Jun-2013 | AN-No. 1TD02

This application note describes how to set up 3GPP FDD and LTE multicell and multi-UE scenarios with the R&S®SMU200A with a focus on routing and leveling of the baseband signals. Furthermore, it describes in detail how to determine the correct AWGN settings, i.e. how to calculate the required signal-to-noise ratio for the various scenarios.

10-Aug-2011 | AN-No. 1GP80

This application note provides a guide through the measurements for IEEE 802.11ac WLAN transmitter signals using the general purpose OFDM analysis software R&S FS-K96. Step-by-step instructions for performing the measurements are provided and the different result types available with the FSK96 Software are discussed.

22-Sep-2011 | AN-No. 1EF82

RTC, RTC1000, Application Card, Determining current-voltage characteristics with the oscilloscope With their included component tester, the R&S®RTC1000 oscilloscopes are universally deployable in development and educational environments. Determining current-voltage characteristics with the oscilloscope RTC, RTC1000, Application Card, Determining current-voltage characteristics with the oscilloscope

20-Dec-2017

RF performance measurements for Wi-Fi 7.

30-May-2022

The new buffer analysis feature was introduced with firmware version 2.80 for the R&S DVM family. This application note describes this feature and explains how it represents a valuable asset to your daily business operations This application note first provides background information and then explains how monitoring and measurement have been implemented in the R&S DVM family.

23-Mar-2006 | AN-No. 7BM53

CST® Filter Designer 3D, which is part of the CST Studio Suite® simulation software from Dassault Systèmes, is a complete synthesis tool for filters and diplexers. It provides a range of solutions throughout the design process of coupled resonator filters and even beyond with its VNA based tuning capability. CST Filter Designer 3D assists in tuning filter hardware, significantly reducing the time for optimizing a device to meet the expected specifications. An attractive instrument to obtain fast data reading for realtime filter tuning is the R&S®ZNB vector network analyzer from Rohde & Schwarz.

27-Nov-2019

With the R&S®RTB2000/RTM3000/RTA4000 oscilloscopes, you control and interact remotely via LAN. These oscilloscopes incorporate the USB-based connectivity standard media transfer protocol (MTP).

20-Mar-2017