For A/V devices such as smartphones, tablet PCs, Blu-ray players, set-top boxes and TV sets, the perceived video quality must satisfy very high standards. A/V devices need to hold their own in three main areas:ı Stability (environmental influences, response to source signal disturbances, etc.)ı Performance (switching times, delays)ı Compliance with standards (input and output formats)Any deviations from the expected video and audio output can be automatically and precisely detected with R&S A/V distortion analysis on all common analog and digital interfaces such as HDMI™ and MHL™.This document examines the relevant setups and configurations.

15-Oct-2014 | AN-No. 7BM87

Create and simulate detailed traffic situations for the verification of cellular V2X (C-V2X) connectivity

30-Jun-2022

The R&S®SMW200A GNSS simulator offers an easy and convenient way to test your receiver design against a wide variety of potential interferers and jammers. Test cases extend from simple coexistence simulations to complex interference scenarios with localized emitters.

28-Jan-2019

Simultaneous DL throughput verification and UL transmission testing with the R&S®CMW500

29-Jul-2009

With the extension of the 3GPP FDD system to include HSDPA, the HS-DPCCH has been added as a new code channel in the uplink. This Application Note describes the transmitter measurements provided by the CMU200 to perform the transmitter measurements defined in TS 34.121 in presence of the HS-DPCCH. CMU200 receiver measurements according to TS 34.121 that measure the throughput and the CQI reporting are described. Subject to change – T. Braun, November 2005 - 1CM62

25-Nov-2005 | AN-No. 1CM62

Modulation Analyzers FMA (up to 1.36 GHz) and FMB (up to 5 GHz) are high-grade FM demodulators from Rohde & Schwarz with highly stable synthesizer, low-noise FM demodulator, automatic frequency tuning and fine-tuning, separation of AM from FM,all of which make Analyzers FMA/FMB ideal for phase noise measurements.

03-Jun-1998 | AN-No. 1EF15

LTE-Advanced comprises multiple features enhancing the basic LTE technology firstly specified in 3GPP Release 8. LTE including the LTEAdvanced improvements was approved by ITU to comply with IMT-Advanced requirements and thus being a true 4G mobile communication system. The different technology components of LTE-Advanced have different market priorities and require different testing strategies. This application note summarizes the Rohde &Schwarz test solutions for LTE-Advanced (Release 10) using Vector Signal Generators, Signal and Spectrum Analyzers and the Wideband Radio Communication Tester.

03-Sep-2014 | AN-No. 1MA166

The I/Q-Modulation Generator AMIQ provides high precision I/Q analog output for data calculated by the software WinIQSIM. Additionally, the software AMIQ-K2 enables you to read, convert, and transfer existing data files from various other programs to AMIQ format. Input formats supported by AMIQ-K2 are: - The propriety R&S programs IQSIM and DAB-K1. - Mathematic calculation programs like Matlab and Mathcad. - AWG202, COSSAP and ADS data files. AMIQ-K2 also provides you with remote control for AMIQ. For hardware and software requirements see section 2. AMIQ-K2 transfers data to AMIQ using either - GPIB - RS232. An extensive manual is supplied to help you use AMIQ-K2.

24-Nov-1999 | AN-No. 1MA10

This application note describes the general setup and required equipment for EMC measurements according to the EMS standard IEC / EN 61000-4-6.

29-Mar-2007 | AN-No. 1SP31

This application note provides information about the spurious emission measurement on 3 GPP base station transmitters. The basic requirements and the limiting factors of a spectrum analyzer are explained in detail. Dynamic range calculations with measurement examples show the practical realisation of spurious emission measurements.

10-Jan-2002 | AN-No. 1EF45

This application note presents means to determine the quality of color-reproduction on TVs and monitors using the R&S®DVSG Digital Video Signal Generator in combination with the Konica Minolta CS-2000 spectroradiometer and the accompanying Konica Minolta CS-S10w analysis software.

13-Aug-2010 | AN-No. 7BM78

A high frequency transformer is a key component when designing isolated switching mode power supplies (SMPS). Leakage inductance is essential in the control of many design parameters including efficiency, maximum voltage rating for switching elements and EMI when it comes to designs using customized transformers. Accurate measurement of this parasitic element is mandatory. The R&S®LCX LCR meter is ideal for this challenging measurement task.

15-Feb-2022

Unique automatic level controlled (ALC) based test setup using the R&S®ZVA vector network analyzer and R&S®BBA150 broadband amplifiers provides highly accurate and reproducible results in minimum test time.

27-Sep-2013

This appication note introduces a program suitable for generating and analyzing WiMAX IEEE 802.16 signals for power amplifier testing. The program allows the user to change the generator settings, to select specific pre-defined test parameters and to analyze the test results. The application note describes the test parameters and the features and capabilities of the program.

03-Aug-2007 | AN-No. RAC-0611-0025

Mobile network operators worldwide face cost pressures and escalating network complexity. The advent of 5G-NR has ushered in new use cases and flexibility, but it also comes with more stringent performance and availability requirements.Machine Learning can serve as a catalyst for the market to unearth deep insights that would otherwise remain concealed. It can also significantly streamline everyday tasks by fostering a smarter system that guides users through their routine work processes, rather than obliging them to repeat each (manual) step. Rohde & Schwarz Mobile Network Testing has focused its efforts on delivering Machine Learning use cases that distill relevant insights from drive testing data, thereby offering substantial benefits to users.This educational note explains the motivation and reasoning why this kind of approach is needed, what are the benefits of the machine learning offering and it takes a deeper look into how it can be used in various levels of statistical and technical analysis. Finally, this document provides real measurement results and analysis findings based on the Rohde & Schwarz post processing SW suite SmartAnalytics and its machine learning based features Call Stability Score and Network Utilization Rating.

28-Feb-2024 | AN-No. 8NT10

The RSIB interface enables the network analyzers of the ZVR family to be controlled by means of Windows applications via DDE. The interface functions are contained in the DLL RSIB.DLL. The other DLL RSDDE.DLL provides functions for the DDE access to the instrument firmware. These functions are used by RSIB.DLL. The interface of these functions greatly corresponds to that of National Instruments for programming the GPIB. The function names are similar to those of the NI library but preceded by RSDLL. The two DLLs are part of the firmware and are updated with the firmware update kits.

31-Jul-1998 | AN-No. 1EZ33

Oscilloscopes are basic everyday instruments for engineers and electricians. Maintenance tasks, however, sometimes require very specific measurements that are not available as standard functionality or are difficult to set up manually. With the R&S®RTH-K38 user scripting option, engineers can now design their own measurement function and a simple user interface. This paper describes how to use this unique feature for railway maintenance work.

06-May-2020

A vector-modulated microwave signal can be generated by mixing an I/Q-modulated signal with a microwave carrier. This Application Note describes the frequency upconversion using a standard passive mixer. The basics of mixer operation are introduced and the conversion process is demonstrated in detail with a test setup and corresponding measurements. The mixer selection guide will make it easier to choose a proper mixer for individual applications.

18-Dec-2008 | AN-No. 1GP65

The Society of Cable Telecommunications Engineers (SCTE) defined the ANSI/SCTE 40 specification: Digital Cable Network Interface Standard. ANSI/SCTE 40 tests are designed to test conformance of set-top boxes and other cable receiving equipment to ensure that they will operate correctly when installed in a cable system. The tests are a combination of noise (AWGN and phase noise), AM hum, micro-reflections, digital and analog adjacent channels, and other discrete interferences. These impairments are found on most cable systems to some degree. Rohde & Schwarz provides set-top box manufacturers with an easy solution to perform conformance testing in line with ANSI/SCTE 40 by using the R&S®SFU broadcast test system and the R&S®SFE100 broadcast tester. The R&S®SFU is able to perform most of the test procedures in one unit. Furthermore, additional test transmitters allow the simulation of full channel loading. This Application Note explains the specific test requirements, a possible setup, and the configuration using the R&S®SFU/SFE100.

29-Oct-2009 | AN-No. 7BM68

To analyse the quality of CD players, lots of measurements have to be done. This application note presents a program, which combines these measurements to an automatically running sequence and gives a printout of the results. A test CD is used for generating the test signals. Here the Audio Test Disc UPA-CD from Rohde & Schwarz is used, which holds all required signals in a sequence permitting automatic measurements to be carried out, without the need of controlling the CD player. In addition, this application note explains the measurements and informs about the different standards.

16-Feb-1998 | AN-No. 1GA21

This document describes WLAN tests which rely on communication (signaling) between R&S®CMW and device under test (DUT) and on transmission of packet data over WLAN. On the R&S®CMW side the WLAN Signaling application is required, for some tests also the Data Application Unit (DAU).The test principles and the necessary settings are explained and background infor-mation is given. Step-by-step procedures are provided for the main configuration tasks.

08-Feb-2016 | AN-No. 1C107

Leaving aside the microwave generators, the present line of Rohde & Schwarz products comprisessignal generators up to 1 GHz (SMX, SMG), up to 2 GHz (SMH, SMGU), up to 3 GHz (SME, SMT) and up to 4.3 GHz (SMHU). For applications at higher frequencies, all signal generators can also be operated with an external passive frequency doubler. This extends the range of possible applications up to 8.6 GHz. Some degraded specs regarding level and modulation are described below. For people using the frequency range 3 to 6 GHz, the low priced combination SMT plus frequency doubler will mainly be interesting. Signal generator SMHU is useful for the frequency range up to 8.6 GHz. Especially the phase noise performance is excellent with this instrument. the required output signal. It should also be pointed out that the residual FM and the SSB phase noise will be 6 dB poorer as a result of frequency doubling.

20-Apr-1998 | AN-No. 1GPAN03

The R&S®Pulse Sequencer software together with the R&S®SMW200A vector signal generator offers a simple and easy way to simulate multi-emitter environments. It enables engineers to validate and verify the EW receiver performance.

13-Nov-2018

The UPL Audio Analyzer can be remote-controlled via the IEEE bus or the RS-232-C interface. Test results are output either individually or in blocks. ASCII or binary files such as setup files can be transferred to the audio analyzer from an external controller. This Application transfers files from the audio analyzer to an external controller via the serial interface. Utility programs for the audio analyzer and the external controller (PC) are required.

15-Nov-2001 | AN-No. 1GA42

The use of Rohde & Schwarz device drivers under VEE software is not complicated. However, a number of factors are involved, the errors that occur are often difficult to diagnose. This application provides easy and detailed support for installation and troubleshooting using National Instruments or Agilent GPIB boards.

20-Dec-2012 | AN-No. 1MA035

The Rohde & Schwarz R&S CMU200 can be configured to perform packet data testing in a Mobile IP or Simple IP environment.This application note is intended as a guide to configuring the necessary Mobile IP or Simple IP network elements and R&S CMU200 instrument.

25-Apr-2007 | AN-No. 1CM51

Welcome to this introductory video show about the R&S® ZVA family of network analyzers. Network analysis is sometimes considered to be cumbersome and difficult to understand, a very offputting reputation for newcomers to network analyzers. To help you look at network analyzers in a different light, we have created this video series. We have intentionally refrained from explaining any theory in depth. Rather, we want to show you how to operate our analyzers for simple and useful applications. As well as just watching this video show, you can also use it as a guide and try yourself. All the operational steps shown only require a standard RF power amplifier which should be available in almost every lab. So, before we get properly started, we hope you enjoy this video show and much success in becoming familiar with network analysis in general, and our R&S products in particular.

13-Feb-2014 | AN-No. 1MA50

- not available -

20-Jul-2001 | AN-No. 7BM11

Almost every switched-mode power supply (SMPS) needs an EMI (Electro Magnetic Interference) input filter to suppress any disturbances of the SMPS on the power lines. This requirement having an input filter in the design ensures that no negative effect will occur in other parts of the systems connected to the power lines. Therefore, the design and the validation of the input filter is a major task during a typical power supply design. The conducted emission (CE) test according to a specific standard is a suitable and a common validation method to release the design at the end of the development cycle. Nowadays, this conducted emission test will be performed as pre-compliance test during the development phase in the lab as well. In this case, the designer will obtain an early feedback whether the design has to be optimized regarding any disturbances present on the power lines. In most cases, the designer has to adjust the input filter to obtain a more effective suppression of disturbances generated by the SMPS. However, the designer needs to know details about the noise spectrum to optimize the input filter as effective as possible. In addition to magnitude and frequency information of the noise source, it would be very helpful to know whether the noise is generated by a common mode source or by a differential mode source. During the standard conducted emission test, common and differential mode noise is a combination in the measurement results and thus not possible to gain deeper insights. This document will describe a method to separate common-mode and differential-mode separation using two oscilloscope channels. This separation approach works without any additional hardware component like a noise separator. The designer will be able to distinguish between common-mode (CM) and differential-mode (DM) noise. This additional information about the dominant mode provides the capability to optimize input filters very efficiently.

17-Sep-2020 | AN-No. GFM353

Vector network analyzers are the most accurate instruments in the microwave engineer’s lab. The R&S®ZNA takes accuracy to a new level. Not only is the instrument extremely precise, but now it also calculates and displays the measurement uncertainty right on the screen as the device under test is being measured.

19-Jul-2021