Download Center

Models: R&S®RTO-K23, R&S®RTP-K23

Models: R&S®RTO-K22, R&S®RTP-K22

Benefits and advantages Benefits and advantages Video, RTO2000, Oscilloscope, Realtime deembedding Benefits and advantages

Rohde & Schwarz Drivers under VEE - Installation and Troubleshooting

20-Dec-2012 | AN-No. 1MA035

Unique trigger capability Unique trigger capability Video, RTO2000, Oscilloscope, Triggering Unique trigger capability

Easy configuration of frequency domain analysis Easy configuration of frequency domain analysis Video, RTO2000, Oscilloscope, Responsive FFT and spectogram Easy configuration of frequency domain analysis

Russian version - времени простоя цифрового осциллографа на измерения

Models: R&S®RTP-K91, R&S®RTO6-K91, R&S®RTP-K93, R&S®RTP-K94, R&S®RTP-K95

Shown on a USB 3.1 Gen1 device Video, RTO2000, Oscilloscope, Signal integrity debugging Shown on a USB 3.1 Gen1 device

How to analyze basic paramters of pulsed RF signals Video, RTO2000, Oscilloscope, How to analyze basic paramters of pulsed RF signals

How to perform signal integrity debugging on a DDR3 device Video, RTO2000, Oscilloscope, DDR3 DDR3 signal integrity debugging

Power rail probe in combination with high performance oscilloscope Video, RTO2000, Oscilloscope, Power integrity debugging Power rail probe in combination with high performance oscilloscope.

Up and down Chirp analysis in time and frequency domain Video, RTO2000, Oscilloscope, Analysis of complex radar signals Up and down Chirp analysis in time and frequency domain

Generating models with a VNA and using these on an oscilloscope via the deembedding

23-May-2023 | AN-No. 1SL393

How to use realtime deembedding on a USB 3.1 Gen1 device video, oscilloscope, RTO2000, USB 3.1 How to use realtime deembedding on a USB 3.1 Gen1 device.

This Application Note addresses signal measurements and analysis of automotive radars that are crucial during the development and verification stages.

10-Jun-2016 | AN-No. 1MA267

Video, oscilloscope, RTO2000, Time delay analysis of multiple wideband RF signals Analysis of multiple RF signals, which are typically used e.g. for direction finding.

Oscilloscope bus decoding, RTO2000, bus decoding, I2C Dive into your protocol to check for any problems with your I²C interface.

This document is divided in two parts and starts with an introduction in AC-DC conversion principles in general. It will present the most common circuits used for different power levels. The switching mode power supply (SMPS) converter will be the main focus as they are used everywhere in the electronics. Especially the flyback converter design in different flavors are highlighted. Nevertheless, all measurements are also applicable for other SMPS converter designs operating at higher power levels.In the second part of this document, most relevant testing methods and procedures of an AC-DC converter are highlighted. For each testing section, a fundamental part will be upfront discussed and it is followed by a presentation of a suitable measurement method. In this second part, the device under test (DUT) is considered as black box device and thus the structure is similar. Therefore, the testing parts consists of methods related to input tests, output tests and a combination of both like efficiency. Of course, some test performed at the output of the converter are also relevant for DC-DC converter, e.g. the validation of the output ripple.

14-Nov-2022 | AN-No. 1SL387

Discover some of the key parameters of an oscilloscope and how they impact on the performance in this video series: Part 1: Bandwidth and frequency response R&S®RTO2000 Video, application videos, oscilloscope, troubleshooting, mixed signal oscilloscope R&S Talking about bandwidth Open Lightbox Talking about bandwidth

The R&S®RTO-K92 eMMC Compliance Test option offers an automated test solution for the electrical interface of an eMMC device according to the JEDEC specification, revision 5.1. Oscilloscope Application Videos, Application Video, Application Videos, Videos, eMMC Interface Compliance Test Learn how you can use the eMMC compliance test of R&S for automated testings of electrical interfaces!

RTO2000, debugging, EMI When debugging EMI problems in electronic circuits, development engineers face the challenging problem of quickly and accurately identifying and eliminating the sources of unwanted emissions. Many problems can be eliminated during development by using oscilloscopes for EMI debugging.

Oscilloscope bus triggering, RTO2000, bus triggering, history mode, break condition Use the hardware trigger to isolate break conditions. Break conditions can be corellated with their root cause one by one using the History Mode.

RTO2000, waveform display, R&S®SmartGrid, complex measurements Use the R&S®SmartGrid function to configure the display. For complex measurement tasks where several screen displays are helpful, you can superposition windows in multiple tabs. All measurement diagrams have labeled scales so you can immediately read important signal characteristics.

This document provides the technical specifications of the R&S®RT-Zxx high voltage and current probes

RTO2000, user interface, toolbar, display, cockpit The advanced user interface enables clear orientation thanks to colour coding, as well as having a high-resolution capacitive touchscreen with gesture support. The toolbar at the top of the screen provides access to frequently used functions such as measurements, zoom and FFT.

Video, RTO2000, Oscilloscope, Power integrity test Today’s highly integrated electronic devices use smaller voltage levels and therefore require much smaller ripple levels on the power rails for reliable operation.

Oscilloscope bus debugging, RTO2000, bus debugging, UART, RS232, RS485 Let your Oscilloscope decode your UART/RS232/RS485 interfaces for you! So you can quickly understand the data and correlate the data content with the electrical signal.

Webinar, RTO2000, Automotive Ethernet compliance testing This webinar presents details on the individual test cases of the compliance test and provides useful information on the required test setup.

RTO2000, toolbar, measurement functions, fast access The toolbar at the top of the screen provides access to frequently used functions such as measurements, zoom and FFT. Configure measurement in a few seconds by simply activating the measurement setup in the toolbar and choosing the desired measurement function and source channel in the sidebar.