156 Results
Signal integrity – measuring rise time using a true differential signal (part 2 of 4)
TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
Signal integrity – measuring differential impedance vs. distance (part 3 of 4)
TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
Simplified test setup using R&S®ZVAB-K30 noise figure measurement option
The R&S®ZVA vector network analyzer in combination with the R&S®ZVAB-K30 noise figure measurement option simplifies noise figure measurement, a key parameter for receiver performance evaluation.
Signal integrity – measuring time domain skew between two lines on a differential transmission (part 4 of 4)
TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
How do I calculate the logarithmic frequency steps for the horizontal axis?
How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?
Measurement of Dielectric Material Properties
This application note describes the techniques to measure the dielectric properties of materials using a vector network analyzer. It also shows methods for converting the s-parameters to dielectric properties.
23-May-2012 | AN-No. RAC-0607-0019
Level-controlled passive intermodulation (PIM) measurements presented at EuMW 2013
ZVA Vector Network Analyzers, PIM, Rohde & Schwarz demonstrated fast and accurate passive intermodulation (PIM) testing of duplex filters at the European Microwave Week 2013 in Nuremberg.
Remote control via drivers: How to set the ports in RSZVB_Select_Calibration_Type
I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?
Multi-port calibration by using a two port calibration unit
This paper shows how to perform a n-port multi-port calibration by using calibration unit with a lower number of ports than available of the vector network analyzer.
06-Feb-2013 | AN-No. 1EZ70
Remote Operation of Windows Based T&M Instruments with Android Tablets
This document describes how a Windows®-based R&S® T&M instrument is remotely operated by an Android™ tablet as if working on it locally.
22-Aug-2013 | AN-No. 1MA236
Rohde & Schwarz Russia: Application guide
Russian version - Измерения в диапазоне миллиметровых волн с использованием преобразователей семейства R&S®ZVA
Rohde & Schwarz Russia: Application guide
Russian version - Измерение S22 усилителя в «горячем» режиме с импульсными сигналами на анализаторе цепей R&S®ZVA
Generating Multiple Phase Coherent Signals – Aligned in Phase and Time
This application note explains how to generate phase coherent signals with a compact easy-to-use solution.
07-Sep-2016 | AN-No. 1GP108
R&S®ZV-Z9x, ZV-Z19x Test Port Cables - Specifications
R&S®ZV-Z9x, ZV-Z19x Test Port Cables - Specifications
R&S®LegacyPro - Instrument emulation – breathing new life into existing test systems - Brochure
R&S®LegacyPro - Instrument emulation – breathing new life into existing test systems - Brochure
Overview of Tests on Radar Systems and Components
This application note along with its corresponding white paper 1MA207 show how to use the R&S radar product portfolio to tackle test and measurement tasks in modern radar technology.
10-Aug-2012 | AN-No. 1MA127
T&M solutions for software defined radios (SDR)
This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.
15-Sep-2012 | AN-No. 1MA206
OTA characterization of passive array antennas for fast testing
Inside the lab and on the production line – this Rohde & Schwarz solution offers speed, accuracy and convenience for testing TX beamforming passive array antennas.
04-May-2018
Identifying defective single elements in antenna arrays
Fault identification in single elements of antenna arrays is possible by scanning in near-field range and applying the near-field to far-field transformation method.
24-Mar-2020
R&S®ZCxxx Millimeterwave Converters - Specifications
This document provides the technical specifications of the R&S®ZCxxx millimeterwave converters.
RPG ZRXxxx Millimeterwave Receiver - Specifications
RPG ZRXxxx Millimeterwave Receiver - Specifications
Testing TRM performance of modern AESA antennas - Flyer
Testing TRM performance of modern AESA antennas - Flyer
Using R&S®Forum Application for Instrument Remote Control
R&S®Forum for Instrument Remote Control
28-Jun-2018 | AN-No. 1MA196
How to use Rohde & Schwarz Instruments in MATLAB
This application note outlines two different approaches for remote-controlling Rohde & Schwarz instruments out of MathWorks MATLAB.
12-Jun-2017 | AN-No. 1MA171
In Situ Calibration Utilizing the R&S®ZN-Z3x Inline Calibration Units
This application note reviews a new calibration subsystem which consists of Inline Calibration Units (ICUs). These ICUs are designed for in situ use, so they are left in place both during the calibration procedure and during the measurement of the Device Under Test (DUT).This adds versatility, convenience and accuracy to the VNA based measurement system, as it means the calibration can be refreshed at any time without manually disconnecting the DUT from the test system.
29-Sep-2017 | AN-No. 1EZ71
R&S®VISA
R&S®VISA is a standardized software library that allows fast communications over diverse interfaces with a wide variety of T&M instruments that are detected on the network from PC applications.
26-May-2020 | AN-No. 1DC02
Development Hints and Best Practices for Using Instrument Drivers
Development Hints and Best Practices for Using Instrument Drivers
01-Jan-2013 | AN-No. 1MA153