Sending a remote Control Command internally

What is the correct pin layout of the DC inputs on the network analyzer's rear panel?

R&S®ZVAX24 Quick Start Guide

I have set my VNA to single sweep mode and switched on averaging with a factor of 10. But when I restart the single sweep, it stops after 1 sweep and the averaging is not done.

Rohde & Schwarz Getting Started for the R&S ZCxxx frequency converters

This application note describes how to configure a Rohde & Schwarz Network Analyzer to make spectral measurements directly on a device under test.

16-Mar-2012 | AN-No. 1EZ62

TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines

I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.

I trigger this single sweep with the RSZVB_Send_Trigger_and_Wait_for_OPC driver, but this driver does not wait for the complete 10 sweeps. If I don't use averaging, this program is works.

How can I switch from remote to local state via remote control?

I query the values of a trace using scpi commands. But I get the y-values only. Is there a possibility to get the y-values also (frequency)?

R&S ZV-WR02/WR03/-WR05 Technical Information

TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

The R&S®ZVA vector network analyzer in combination with the R&S®ZVAB-K30 noise figure measurement option simplifies noise figure measurement, a key parameter for receiver performance evaluation.

TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?

R&S ZV-WR06/-WR08/-WR10/-WR12/-WR15 Technical Information

Rohde & Schwarz Technical Information for the R&S ZV-Z129/-Z135/-Z170 calibration kits.

This application note describes the techniques to measure the dielectric properties of materials using a vector network analyzer. It also shows methods for converting the s-parameters to dielectric properties.

23-May-2012 | AN-No. RAC-0607-0019

ZVA Vector Network Analyzers, PIM, Rohde & Schwarz demonstrated fast and accurate passive intermodulation (PIM) testing of duplex filters at the European Microwave Week 2013 in Nuremberg.

Rohde & Schwarz Technical Information for the R&S ZN-Z170/-Z135/-Z129/-Z129E calibration kits.

I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?

Listing of all video overview pages sorted by categories and themes. Looking for additional insight on a specific application or measurement technique? Pick your topic of interest.

This paper shows how to perform a n-port multi-port calibration by using calibration unit with a lower number of ports than available of the vector network analyzer.

06-Feb-2013 | AN-No. 1EZ70

This document describes how a Windows®-based R&S® T&M instrument is remotely operated by an Android™ tablet as if working on it locally.

22-Aug-2013 | AN-No. 1MA236

Russian version - Измерения в диапазоне миллиметровых волн с использованием преобразователей семейства R&S®ZVA

Russian version - Измерение S22 усилителя в «горячем» режиме с импульсными сигналами на анализаторе цепей R&S®ZVA

This application note explains how to generate phase coherent signals with a compact easy-to-use solution.

07-Sep-2016 | AN-No. 1GP108

This application note along with its corresponding white paper 1MA207 show how to use the R&S radar product portfolio to tackle test and measurement tasks in modern radar technology.

10-Aug-2012 | AN-No. 1MA127