CompactTSVP, monitoring systems, tire pressure, RF signal, microcontroller, ISM, wireless transmission Function Test of Tire Pressure Monitoring Systems Function Test of Tire Pressure Monitoring Systems CompactTSVP, monitoring systems, tire pressure, RF signal, microcontroller, ISM, wireless transmission Function Test of Tire Pressure Monitoring Systems Function Test of Tire Pressure Monitoring Systems

10-May-2006

Automotive Infotainment Testing

24-Apr-2018

Battery life time is usually one of the most important specifications for battery-powered devices. Depending on the application, life time requirements can range from tens of hours for typical wearables like smart watches to ten years for smart sensors. Understanding where and when energy is used in order to minimize power consumption is therefore key for any of these devices.The power consumption analysis tool was developed to make it easier for customers to analyze power consumption data collected with either the NGL, NGM or NGU power supplies from Rohde & Schwarz. It allows to easily capture power consumption data and analyze using basic measurements.

31-Jan-2022 | AN-No. 1SL380

GSM standard 11.10 prescribes a number of tests requiring measurements on mobile stations under multichannel conditions (fading). The combination of Radiocommunication Tester CRTP02 or CRTC02 and Signal Generator SMIQ allows cost-effective performance of the most important fading tests, in particular the tests according to sections 13.2, 14.2 and 14.3 of GSM 11.10. The aim of this application note is to familiarize the user with all the capabilities offered by the above combination of measuring instruments. The user should then be able to quickly generate and run his own fading tests using the IEC/IEEE-bus control commands described in this application note. To facilitate reading of the following, the testers CRTP02 and CRTC02 are referred to as CRTx.

07-Nov-1997 | AN-No. 1MA02

3GPP TS25.141 defines conformance tests for W-CDMA base stations (including HSPA+ features). This application note describes how all required receiver (Rx) tests (TS25.141 Chapter 7) can be performed easily and quickly by using vector signal generators and CW sources from Rohde & Schwarz. One test additionally requires a spectrum analyzer from Rohde & Schwarz.Example illustrates manual operation. A free software program enables and demonstrates remote operation. The W-CDMA base station transmitter (Tx) tests (TS25.141 Chapter 6) are described in Application Note 1MA67.

21-Oct-2014 | AN-No. 1MA114

Today’s electronic devices often draw non-sinusoidal, irregular current where harmonic current is fed back into the universal supply system. Monitoring this current is both crucial and mandatory for CE compliant devices. The R&S®NPA701 compliance tester seamlessly and efficiently monitors this current.

28-Mar-2024

This Application Note describes two easy ways of extracting the video content of MPEG-2 transport streams and storing it as video elementary streams. These elementary streams can later be used to generate customized MPEG-2 transport streams by means of the Advanced Stream Combiner R&S DVASC application.

21-Apr-2006 | AN-No. 7BM58

Signal Generator SMIQ has versatile analog and digital internal modulation capabilities. Optional Fading Simulator SMIQ-B14 adds a variety of fading functions to the integrated digital modulation capabilities of SMIQ at a highly attractive price as compared with similar products. This application note describes how to apply fading to signals of any source and with any type of modulation (analog and digital) in a very convenient way.

09-Mar-1998 | AN-No. 1MA07

Spectrum Rider, FPH, FPH handheld spectrum analyzer, satellite ground station Satellite ground station testing up to 44 GHz with the R&S®Spectrum Rider FPH handheld spectrum analyzer Satellite ground station testing up to 44 GHz with the R&S®Spectrum Rider FPH handheld spectrum analyzer Spectrum Rider, FPH, FPH handheld spectrum analyzer, satellite ground station Satellite ground station testing up

24-Jul-2024

Digital pre-distortion (DPD) is a common method to linearize the output signal of a power amplifier (PA), which is being operated in its non-linear operating range.Most PAs operate in their non-linear range for efficiency reasons. The drawback of higher efficiency is the non-linear operating range. In order to maintain signal quality, many transmitters employ DPD. Implementing real-time DPD in a transmitter is a challenging task and often ends in PA models, which are specific to the signal transmitted.Even though these complex models are required for transmitter development, they are not needed during PA verification and development.This article describes an approach to generate a pre-distorted signal based on a hard-clipper. The resulting waveform pushes the output of the DUT as close to the hard-clipper as possible.Due to the waveform approach, the algorithm compensates all memory effects.

13-Sep-2017 | AN-No. 1EF99

Using the internal R&S®ESMD-IGT GPS module and external GPS antenna in the R&S®ESMD wideband monitoring receiver

30-Apr-2013

Automated long-term measurements expand snapshot measurements associated with risk communication

12-Jun-2007

SMW200A, SMZ90, Pulse Sequencer software, vector signal generator, frequency multiplier, Automotive radar sensors, Testing automotive radars Testing automotive radars against norm interferers; The R&S ® Pulse Sequencer software simulates arbitrary RF environments and supports the generation of radar norm interferers to test automotive radars operating in the 24 GHz, 77 GHz and 79 GHz frequency band

20-Oct-2016

Performing precompliance measurements on power supplies requires using a line impedance stabilization network (LISN) for results that can be compared to limit values. While LISNs are standard in any precompliance lab, often no LISN is available for early R&D testing. If high accuracy is not your goal and you just need a simple tool for debugging, you can build your own LISN. Rohde & Schwarz oscilloscopes with powerful FFT analysis, are ideal for optimizing EMI filters or debugging unwanted emissions during development.

14-Jan-2021

Testing radomes, bumpers, QAR50 Ensure a high level of performance and reduce performance degradation of automotive radar sensors caused by radomes and bumpers with the R&S®QAR50. Testing radomes and bumpers in all phases – from design to high-volume production Testing radomes, bumpers, QAR50 Ensure a high level of performance and reduce performance degradation of automotive radar sensors caused by

21-Apr-2022

This Application Note describes signal generation with carrier aggregation for 802.16m based on 802.16e signals in practical important configurations using one or more Vector Signal Generators R&S SMU200A or R&S SMBV100A. Various examples illustrate how to analyze these signals using the Vector Signal Analyzer R&S FSQ, R&S FSG or R&S FSV.

22-Mar-2010 | AN-No. 1MA173

Best practices for national regulatory authorities

Key points:Importance of field measurements: Traditional network planning tools and models only offer an estimated view of mobile coverage. Field measurements are conducted under real geographical and load conditions, and therefore provide a more accurate picture and can discover interferences more effectively. Coverage investigations: When deploying a mobile network, operators must adhere to regulatory standards and licensing conditions. As a result, regulatory authorities carry out field measurements on a regular or ad hoc basis to validate compliance or investigate customer complaints. This process identifies coverage gaps and areas of poor network quality, enabling regulatory authorities to take actions to enhance service quality for consumers and guide network expansion.Foster competition: If the field measurements of the coverage and performance are performed on a scale representative of a given country, the transparency of these results can promote healthy competition between operators and better service for consumers, which is essential for economic growth and social development.Measurement Techniques: The harmonized methodology for measuring and evaluating data throughput and QoE based on popular services is described in ETSI TR 103 559.

15-Apr-2024 | AN-No. 8NT14

A collection of frequently occurring customer questions on using the ZVR analyzer, calibration, virtual transform networks, and additional applications.

23-Jan-2002 | AN-No. 1EZ38

While Mobile phones are allowed to require approximately 3 time slots for switching from transmission to reception, base stations must be able to transmit and receive at a new frequency in every time slot in the frequency hopping mode. This behaviour must of course be tested and measurements carried out on the base station transmitter and receiver. Since there is no signal generator which is able to settle at different frequencies from one to the next time slot with GSM modulation, a solution to this problem was found by linking two Signal Generators SME in such a way that they alternately provide signals at different frequencies.

01-Jul-1999 | AN-No. 1GPAN28

Automated Solution with High Efficiency

5G New Radio (NR) presents dramatic challenges to the testing of User Equipment (UE) Power Amplifier (PA). Multiple frequency bands, flexible 5G operation mode, multiple PA performance metrics and the MIPI control interface increases the potential PA testing workload significantly. Manually repeating these tests under so many different scenarios can be costly and time consuming. An automated testing solution can help the test engineer to highly improve the testing efficiency.In this application note, it introduces an example of automated testing of 5G UE PA with R&S signal generator, signal and spectrum analyzer, vector signal explorer software, power meter along with power supply.The entire application note is organized with following structure:Chapter 2 outlines the challenges to 5G UE PA testing.Chapter 3 introduces the setup for 5G signal generation and analysis. For 5G signal generation, a batch program of converting *.CSV files with IQ vectors to ARB waveform files is introduced. For 5G signal analysis, the R&S®VSE software is recommended, which enables the separation of RF signal collection and measurement to improve testing efficiency.Chapter 4 provides the informative content about the integration of MIPI control interface for the PA ON/OFF state switching and register configuration.Chapter 5 gives a guide on the implementation of a quick power servo, in which the techniques to speed up the PA power level adjustment are discussed.Chapter 6 summarizes the automated testing procedure.

09-Aug-2021 | AN-No. 1SL365

Embedding and De-Embedding of virtual transformation networks for measuring scattering parameters with a ZVR or ZVC vector network analyzer.

25-Sep-1998 | AN-No. 1EZ45

The R&S®CMX500 radio communication tester is ideal for analyzing VoNR and VoLTE voice quality and performance in mobile devices.

21-Feb-2023

From designing a test setup to performing accurate measurements

Double-Pulse testing is a standard test-method used in power electronics design. Accurate measurements require a careful design of the test setup and the selection of the right measurement instruments. This application note discusses important aspects of double-pulse test setups as well as how to perform accurate measurements.

22-Mar-2021 | AN-No. GFM347

This application note describes the configuration of a Miracast wireless video transmission system and how to measure the delay times between a smart phone or tablet (source) and a television / monitor (sink) display. The accompanying software for Windows 7/8/10, Mac OS X 10.x and MATLAB additionally allows to measure the delay until the video signal is transmitted over the air and optionally until it is available on the HDMI cable of an external Miracast receiver.

01-Oct-2015 | AN-No. 1MA250

Overview of the choices for downloading waveform data for remote processing

15-Feb-2018

Antennas have become an integral part of consumer electronics, even in small portable devices that rely on an energy source with limited capacity. Consequently, antennas need to be physically small and power efficient.

05-Mar-2020

The purpose of the test setup described is to ensure or to enhance the level accuracy of signal generators or the generator part of communication testers. The level accuracy of test signals is particularly important at low levels when measuring BER level sensitivity at digital communication receivers. The highly linear FSP spectrum analyzer is used in combination with a power meter to get the best possible accuracy with high measurement speed over a very wide level range.

18-Feb-2011 | AN-No. 1MA21

Over the past few years, electronics developers have developed a variety of approaches to avoid interference on high-speed signals on printed circuit boards. However, with increasing complexity and frequency, PCBs set new limits, supporting frequencies of 40 GHz and higher. Driven by the fast growing 5G market, today’s digital systems operate in these high frequency ranges that come with completely new challenges. With slope steepness’s of just a few picoseconds, any discontinuity in the impedance and impairment of the inductance or capacitance on the PCB or back drill defects on the PCB can have a massive impact on the signal quality. The industry recognizes that there is a growing need for functional high-speed testing of PCBs. The MicroCraft® E2V6151 series combined with an R&S®ZNB vector signal analyzer delivers a fully automated solution.

25-Mar-2020

Your measurement task: To analyze an RF module via its digital interface. This Application Note explains how. As interfaces between the baseband and the RF modules of mobile radio base stations and terminals are increasingly digital, instruments for testing such modules need digital baseband interfaces as well. The R&S®EX-IQ-Box is a digital interface adapter that provides digital baseband I/O for Rohde & Schwarz signal generators and signal analyzers. An R&S signal analyzer with digital baseband interface R&S®FSQ-B17 can analyze digital baseband components input from the R&S®EX-IQ-Box. Data collected with a test-setup consisting of an R&S signal analyzer and the digital interface adapter R&S®EX-IQ-Box can be used in an Agilent ADS environment. For details of how to input the results to ADS, see Application Note 1MA72: 'Using R&S® Instruments within Agilent®ADS®Software'

26-Jun-2009 | AN-No. 1MA147

The R&S®SMC100A signal generator offers a remote emulation feature that makes it possible to control the instrument by commands other than the built-in native SCPI commands. This feature allows the user to replace signal generators, e.g. from other manufacturers, with the R&S®SMC100A without having to change the remote control code. This application note describes how to use the remote emulation feature in general. Furthermore, it describes in detail the remote emulation for each supported instrument, limitations of the individual emulations and the remaining differences between the emulated and the original commands.

28-Feb-2012 | AN-No. 1GP90