The R&S®SMBV100A is both, a versatile general-purpose vector signal generator and a powerful GNSS signal simulator. It can simulate up to 24 satellites in realtime for testing GNSS receivers flexibly, reliably, and cost-efficiently. The R&S®SMBV100A supports receiver testing under realistic conditions by offering features such as obscuration simulation and automatic multipath generation. Out of a multitude of possible test scenarios – with predefined or user-specific settings – this application note presents some examples to give an impression of the instrument’s capabilities.

19-Apr-2018 | AN-No. 1GP101

The R&S®EVSG1000 and R&S®EVSF1000 are signal level and modulation analyzers that reliably analyze GBAS systems during ground and flight inspection when used together with the R&S®EVSG-K4 option.

27-Jun-2019

The R&S®FSW signal and spectrum analyzer measures and analyzes time sidelobes to optimize compressed radar signals as well as radar hardware components and systems. Developers of radar systems can improve and immediately validate their design using automated and reproducible measurements.

22-Oct-2020

High throughput is the key production metric for efficient operation. Improving test speed helps reduce the cost per device. The R&S®PVT360A performance vector tester is optimized for high speed production tests.

12-Apr-2023

This application note shows how to configure the R&S®AdVISE visual inspection software to automate the immunity testing in line with EN 55020 and CISPR 35 on TV sets and monitors.

30-Jul-2020 | AN-No. 1S007

Its dual-path concept plus its ability to duplicate baseband signals make the R&S®SMW200A vector signal generator ideal for efficient GSM/EDGE AMsuppression conformance testing.

28-Feb-2017

PESQ measurements employ a level adaptation algorithm and are hence widely insensitive to absolute level. However, if the tests are performed via a speech codec, the driving level of the codec has an influence on the MOS result. Therefore careful alignment of the level is required. This application note provides an application program which runs on the Audio Analyzer R&S UPV or R&S UPV66 and can be used to calibrate signal levels for the PESQ measurement.

30-Jun-2011 | AN-No. 1GA50

Testing the RF parameters of a WCDMA base station during the network rollout phase ensures subsequent trouble-free operation of networks as a basic prerequisite for general UMTS customer acceptance. This document describes a complete solution for testing the main transmission and reception parameters according to Specification 3GPP TS 25.141 FDD R99 on the basis of the R&S CMU300 Radio Communication Tester (RF measurements) and the NetHawk RNC/Iub Simulator (base station controller). The solution presented here is particularly recommended for installation measurements and regression tests on new UMTS system components.

15-Oct-2004 | AN-No. 1CM56

The R&S®MobileView app lets users operate Rohde & Schwarz instruments remotely and eliminates the need for physical interactions with the instruments.

04-Sep-2024

During wireless transmission over the air a signal is subject to fading. Since fading can strongly influence the communication, devices such as mobile phones must be tested under real-world conditions to verify their performance. The Rohde & Schwarz vector signal generators R&S®SMW200A, R&S®SMU200A and R&S®AMU200A make it possible to perform such tests. Their integrated real-time fading simulators reproduce well-defined and repeatable real-world test scenarios to bring reality into your laboratory. A multitude of standard-compliant, preconfigured fading scenarios make the configuration as easy as possible.This application note gives a brief introduction to fading and explains how to use the fading simulators in custom applications.

26-Apr-2013 | AN-No. 1GP99

Its high measurement speed makes the R&S®EVS300 level and modulation analyzer ideal for reliable ILS runway measurements at maximum speed.

16-Dec-2015

Polar modulation is a method where digital modulation is realized as a combination of phase and amplitude modulation, rather than using an I/Q modulator. This technique becomes increasingly important in mobile communication. This application note shows how to generate polar modulation with an R&S®SMU200A Vector Signal Generator.

26-Nov-2004 | AN-No. 1GP58

The R&S®ZNB vector network analyzer is easy to configure and calibrate using the built-in intermodulation wizard.

19-Dec-2013

Today’s electronic devices often draw non-sinusoidal, irregular current where harmonic current is fed back into the universal supply system. Monitoring this current is both crucial and mandatory for CE compliant devices. The R&S®NPA701 compliance tester seamlessly and efficiently monitors this current.

28-Mar-2024

This Application Note describes two easy ways of extracting the video content of MPEG-2 transport streams and storing it as video elementary streams. These elementary streams can later be used to generate customized MPEG-2 transport streams by means of the Advanced Stream Combiner R&S DVASC application.

21-Apr-2006 | AN-No. 7BM58

Vector Network Analyzers of the ZVR family measure magnitude and phase of complex S-parameters of a device under test (DUT) in the frequency domain. Using an inverse Fourier transform, the results can be transformed to the time domain. The impulse or step response of the DUT is obtained, which gives an especially clear representation of its characteristics. For instance, faults in cables can be directly localized. Moreover, special time domain filters, so-called gates, can be used to suppress unwanted signal components such as multireflections.

04-Aug-1998 | AN-No. 1EZ44

Testing radomes, bumpers, QAR50 Ensure a high level of performance and reduce performance degradation of automotive radar sensors caused by radomes and bumpers with the R&S®QAR50. Testing radomes and bumpers in all phases – from design to high-volume production Testing radomes, bumpers, QAR50 Ensure a high level of performance and reduce performance degradation of automotive radar sensors caused by

21-Apr-2022

Adjacent Channel Power performance of power amplifiers used in digital TV systems has to be guaranteed over a wide frequency range, 54 to 890 MHz, which may lead to time consuming test procedures. The application software described here provides swept ACP analysis, using AMIQ and SMIQ for signal generation and FSP, FSU or FSE for signal analysis. ACP measurement is performed according to FCC Regulation 47CFR 73.622(h).

16-Oct-2001 | AN-No. 1MA43

Due to its full IP system architecture and distributed infrastructure, the CERTIUM VCS is perfectly suited for integration into a virtual center.

10-Mar-2014

The introduction of the transmission of compressed TV signals to MPEG2 and DVB for cable, satellite and terrestrial (COFDM) lead to the creation of many abbreviations that have to be explained to the “uninitiated”. In the previous three lines, three abbreviations whose meanings are not obvious have already been mentioned. A table explaining what these abbreviations mean is therefore essential.

20-Jul-2001 | AN-No. 7BM27

The aim of this application note is to provide information regarding Rohde & Schwarz (R&S®) instrument drivers for R&S®CMU200. This document describes how to use the R&S®CMU200 VXIPlug&Play drivers in Microsoft Visual Basic.NET or C# using Visual Studio.

30-Jun-2009 | AN-No. 1MA157

Today’s complex circuits must integrate several components that feed on different power levels. A robust circuit that ensures interoperability of these components needs carefully designed, clean and stable power distribution networks for power timing. At lower voltage levels, tolerance is defined in percentages and can make precise measurements challenging.

22-Apr-2024

This Application Note describes measurements compliant with the CDMA2000 base station standard described in 3GPP2 C.S0010-C v2.0 / TIA/EIA-97-F-1. The primary focus is on solutions for generating and analyzing CDMA2000 signals. The special characteristics that make the selected signal generators and signal analyzers highly suitable for this purpose are detailed, and remote control programming is demonstrated by means of a free-of-charge program.

15-Sep-2009 | AN-No. 1MA109

In many applications, circuitries with automatic gain control are used, for example in the fields of tape recording or hearing aids. This application note describes the typical characteristic of these control circuitries and the difficulties in measurements using oscilloscops. With the audio analyzers UPL and UPD these measurements can be done much easier, the analysis can be done manually or automatically by using a special software tool.

04-Jun-1998 | AN-No. 1GA32

Compensating external components using their S-parameters and R&S®FSW-K544

18-Mar-2019

Phase distortions in a transmission channel are determined using group delay measurements, they must be as low as possible to maintain good signal quality. Vector network analyzers are normally used to characterize the group delay variations as a measure of phase distortion.This application note provides basic information about the concept of a group delay measurement with spectrum analyzers and signal generators, and how this method simplifies the test setup and improves the measurement speed.Measurement examples show the limiting factors of this approach and help the user to understand and avoid some limitations of this method. In addition the test results are compared to those generated with vector network analyzers.

09-Aug-2017 | AN-No. 1EF98

The R&S MATLAB® Toolkit for Signal Generators provides routines for remote controlling these instruments. Additional MATLAB® scripts turn I/Q vectors into the Rohde & Schwarz waveform file format for use with an ARB. This application note describes the installation and use of the R&S MATLAB® Toolkit on Microsoft Widows and Linux based systems.

26-Apr-2013 | AN-No. 1GP60

The R&S®QPS product family provides high resolution security scanning and was specifically designed to promote faster, more effective and comfortable people screening at security checkpoints. Utilizing safe millimeterwave radio frequency technology, the R&S®QPS security scanners automatically and safely detect potentially dangerous person-borne threats and contraband.

24-Jan-2019

Ensure that your M2M device equipped with an embedded SIM can deliver permanent and ubiquitous connectivity around the globe

22-Aug-2019

Verification of baseband data is an important step in the early development phase of LTE/LTE-A-ready products. Comparison values for baseband data (test vectors) from other sources can be very useful in order to verify the correct implementation of the standard. Option K81 for the R&S®SMx200A vector signal generator offers sample data for LTE at the bit level. The reference data enables users to test their own implementation of the specification. The LTE bit stream verification program shown here uses data generated by this option and offers a (bitwise) comparison with bit streams generated for an LTE downlink signal. Therefore it demonstrates, how easy the option R&S SMx-K81 can be integrated into the simulation and design process during the development of LTE/LTE-A handsets or base stations.

02-Feb-2011 | AN-No. 1MA161