Characterizing RF mixers that have an internal LO using the value-of-three R&S®FPC1500 spectrum analyzer.

15-Oct-2018

CompactTSVP, monitoring systems, tire pressure, RF signal, microcontroller, ISM, wireless transmission Function Test of Tire Pressure Monitoring Systems Function Test of Tire Pressure Monitoring Systems CompactTSVP, monitoring systems, tire pressure, RF signal, microcontroller, ISM, wireless transmission Function Test of Tire Pressure Monitoring Systems Function Test of Tire Pressure Monitoring Systems

10-May-2006

Automotive Infotainment Testing

24-Apr-2018

Distortions caused by components in the RFFE (radio frequency front end) limit the performance and throughput of communications systems. Types of distortions include:▪ AM-AM and AM-PM (complex variations of gain with amplitude)▪ Non-linear frequency response (memory effect)All RFFE components exhibit all of these distortions, only the proportions vary. In this Application Note, illustrative measurements of individual RFFE components, as well as a complete RFFE, will be made. This is followed by the documentation of a more complete analysis, including comparison against theoretical limits, of a linearized commercial SatCom BUC product.

27-Feb-2017 | AN-No. 1MA299

Battery life time is usually one of the most important specifications for battery-powered devices. Depending on the application, life time requirements can range from tens of hours for typical wearables like smart watches to ten years for smart sensors. Understanding where and when energy is used in order to minimize power consumption is therefore key for any of these devices.The power consumption analysis tool was developed to make it easier for customers to analyze power consumption data collected with either the NGL, NGM or NGU power supplies from Rohde & Schwarz. It allows to easily capture power consumption data and analyze using basic measurements.

31-Jan-2022 | AN-No. 1SL380

Sequencer Software Tool

14-Mar-2016

Digital pre-distortion (DPD) is a common method to linearize the output signal of a power amplifier (PA), which is being operated in its non-linear operating range.Most PAs operate in their non-linear range for efficiency reasons. The drawback of higher efficiency is the non-linear operating range. In order to maintain signal quality, many transmitters employ DPD. Implementing real-time DPD in a transmitter is a challenging task and often ends in PA models, which are specific to the signal transmitted.Even though these complex models are required for transmitter development, they are not needed during PA verification and development.This article describes an approach to generate a pre-distorted signal based on a hard-clipper. The resulting waveform pushes the output of the DUT as close to the hard-clipper as possible.Due to the waveform approach, the algorithm compensates all memory effects.

13-Sep-2017 | AN-No. 1EF99

Using the internal R&S®ESMD-IGT GPS module and external GPS antenna in the R&S®ESMD wideband monitoring receiver

30-Apr-2013

IEEE 802.15.4 (ZigBee) uses Offset QPSK with a half-sine pulse-shaping filter as modulation. This application note describes how to set up the Rohde & Schwarz signal analyzers together with the corresponding vector signal analysis (VSA) personality for modulation quality measurements, especially EVM, for ZigBee.

12-Dec-2014 | AN-No. 1EF55

Measurements of very high noise figure components are performed for a number of reasons. For instance, in a wide range of applications, devices under test (DUT) are characterized within a complex test setup that includes high losses before or after the low noise DUT. In case of high frequencies, the switch matrix with complex signal routing and cables might have a very high loss. In other cases, the device might be embedded in a test setup where direct access is physically impossible, on-wafer probing is one example for this case. Using conventional measurement equipment, the noise figure measurement of such a device is very unstable if not impossible at all.

24-Jun-2020 | AN-No. 1EF110

The R&S®EB500 offers level measurement of signals with 20 MHz bandwidth.

09-Oct-2012

Load pull is a powerful method for characterizing RF power amplifiers through impedance variation. Load pull enables model extraction and validation as well as performance, ruggedness and efficiency testing.

02-Sep-2020

This application note examines both the theory and practice of state-of-the-art spectrum analysis by discussing specific measurements taken on an integrated RF amplifier.The theoretical portion of this document first describes how modern spectrum analyzers are designed and how they work. That is followed by a brief characterization of today's signal generators, which are needed as a stimulus when performing amplifier measurements. The effects on the spectrum that are caused by the nonlinearity of real devices under test are derived mathematically.The practical portion of this application note contains detailed test and measurement tasks that are suitable for use as lab exercises performed in small groups. The purpose of these tasks is to illustrate the explanations provided in the theoretical section and to provide a deeper understanding of the principles explained there.

05-Mar-2013 | AN-No. 1MA201

With advanced FFT capabilities and unparalleled sensitivity and dynamic range, the MXO oscilloscopes are the perfect choice for electromagnetic interference (EMI) debugging. Swiftly and accurately detect and analyze EMI emanating from electronic circuits and boards with time-correlated RF analysis. Elevate your debugging experience with the fast performance of the MXO oscilloscopes.

07-Feb-2024

The option ZVR-B7 allows an enhanced power calibration of the source and of the receiver channels of a ZVR, then being active instead of the standard factory power calibration. Using an external power meter, the power level of input or output wave quantities will be adjusted to a desired value at an arbitrary reference plane.

29-Jul-1998 | AN-No. 1EZ41

The power efficiency of the drive electronics is a key parameter when developing electric drive systems. The conduction loss of the electric drive electronics is of special interest. One important parameter for determining the conduction loss is the RDS(on) of the MOSFET. When a switching MOSFET is off, it has a high drain-to-source voltage, but when it is turned on, the voltage drops to just a few hundred millivolts. A highresolution oscilloscope is needed to measure these low voltages. Probe compensation and correct probing are also vital for accurate RDS(on) measurements.

19-Mar-2015

The R&S®ZNA vector network analyzer with integrated LO output and direct IF input options is a simple, cost-effective solution for 2-port and 4-port measurements using Rohde & Schwarz mmWave converters.

19-Jul-2021

This application note explains step by step all necessary settings for transmitting parameters of the disturbance signal from an EMS test to a dAV Camera System via serial port or LAN interface. The dAV Camera System overlays these parameters onto the camera signal.

10-Dec-2019

This application note describes how to use the mask and limit test features of the R&S®RTO, R&S®RTE and R&S®RTM Digital Oscilloscopes for EUT monitoring of signal forms, jitter etc. with the R&S®EMC32 Measurement Software. The mask test function allows autonomous characterization of digital signal integrity during EMS tests. R&S®EMC32 software records violations of userdefined limits or mask templates and evaluates the immunity threshold at frequencies of critical electromagnetic susceptibility.

20-Apr-2015 | AN-No. 1MA242

This application note shows how to perform Bluetooth transmitter measurements with the CMU200 in a reduced signaling mode, in which the protocol handshake between the Bluetooth Equipment Under Test, the EUT, and CMU200 is skipped. This additional CMU200 feature allows both more flexible and faster RF testing of Bluetooth modules. A step-by-step example with SMIQ demonstrates the principles and serves as a reference for integrating this method in user-specific test strategies.

04-Feb-2003 | AN-No. 1MA49

With a Rohde & Schwarz oscilloscope

18-Dec-2018

This application note provides a description of the Rohde & Schwarz Click Rate Analyzer software.In conjunction with the R&S®ESR EMI Test Receiver 4-channel operation is applicable. With R&S®ESU and R&S®ESCI EMI Test Receivers the Click Rate Analyzer software is limited to one channel. This software performs click rate analysis in accordance with CISPR 16-1-1 and CISPR 14-1 / EN 55014-1. It features realtime graphic display of the maximum peak and quasi-peak values. After the measurement, a test report can be displayed and printed.

15-Jan-2015 | AN-No. 1EE25

This application note provides hints for implementing remote control programs using Rohde & Schwarz spectrum and network analyzers. The document makes suggestions for improved remote control performance and describes aspects of measurement synchronization in detail. Finally the document discusses some typical challenges of remote control in production test.

19-Aug-2014 | AN-No. 1EF62

For the transmission of digial audio data, different data formats are in use. The AES/EBU format, which is used in professional applications, as well as the S/P DIF format used in consumer electronics, transmit the audio data in time multplex for both channels. Additonal bits in the data stream cover complementary information, respectively are used for error detection.The generation and the analysis of those protocol data using the audio analyzers UPD or UPL is the topic of this application note. An extract of the AES3 standard informs about the basic definitions.

04-Jun-1998 | AN-No. 1GA15

This educational note covers the theory and practice oscilloscopes based on concrete measurement examples that address authentic everyday tasks.The theoretical portion of this paper begins with an explanation of the basic operating concepts for oscilloscopes, followed by a discussion of the most important parameters to be considered when setting up and performing the exercise measurements. The practical portion of the educational note contains detailed measurement tasks that can be performed by small groups in the university lab. These exercises are intended to demonstrate and reinforce the knowledge gained in the theoretical portion. The exercises build upon one another and demonstrate measurement tasks that are frequently encountered by engineers in daily work.

16-Jan-2018 | AN-No. 1MA265

Air Traffic Control (ATC) radar, military Air Traffic Surveillance (ATS) radar and meteorological radar operate in S-Band frequency range. In fact 4G communication systems such as Long Term Evolution (LTE) make also use of these frequencies. Test and measurement of their coexistence is absolutely essential as performance degradation of mobile devices and networks and even malfunction of ATC radars has been proven.This application note describes LTE and S-Band radar coexistence test and measurement. It addresses LTE user equipment, base stations and S-Band radars and presents test solutions.

28-Mar-2014 | AN-No. 1MA211

This application note explains the concept of Adjacent Channel Leakage Ratio (ACLR) measurement on 3GPP W-CDMA signals with the spectrum analyzer FSP. Optimum operation for both the integrated bandwidth method and the new time domain method are shown via explanation of the signal behavior and the internal structure of the FSP. With the time domain method the spectrum analyzer family FSP provides a new approach featuring a very short measurement time compared to the integrated bandwidth method.

12-Jan-2001 | AN-No. 1EF41

This application note illustrates the operation of the OFDM measurement software R&S FSQ-K96. It describes applications, setup, features, settings and results. Further it concentrates on generating the configuration file for R&S FSQ-K96, the appropriate IQ data files for Signal Analyzer R&S FSQ and waveform files for R&S Signal Generators. With this description the user obtains a complete R&S test solution for signal generation and analysis of generic OFDM signals.

17-Oct-2008 | AN-No. 1EF65

The 3GPP TS 36.521-1 “Radio transmission and reception” LTE User Equipment (UE) conformance specification defines the measurement procedures for LTE terminals with regard to their transmitting characteristics, receiving characteristics and performance requirements as part of the 3G Long Term Evolution (3G LTE) standard.This application note describes how to use the LTE Frequency Division Duplex (FDD) and Time Division Duplex (TDD) measurement functionality associated with the Downlink Carrier Aggregation feature of the R&S®CMW500 wideband radio communication tester to perform LTE R10 receiver measurements according to this test specification.

09-Apr-2015 | AN-No. 1CM103

This application note shows how to run 3GPP WCDMA BER and BLER tests according to standard TS 25.141 with the Vector Signal Generators R&S®SMBV100A, R&S®SMJ100A, or R&S®SMU200A. The description of hardware test setup is followed by detailed instructions on how to configure the R&S® generators and how to run a BER or BLER test step by step. Remote control commands for the generators are included, to simplify integrating the BER/BLER tests into your proprietary test suite.

06-Mar-2009 | AN-No. 1MA144