Performing a multi-port calibration of a vector network analyzer (VNA) is straight forward by using either a calibration unit with the corresponding numbers of ports or single calibration standards. This paper shows how to perform a n-port multi-port calibration by using calibration unit with a lower number of ports than available of the vector network analyzer.

06-Feb-2013 | AN-No. 1EZ70

IEEE 802.16m is an amendment to the release IEEE 802.16-2009 standard. The goal set out in 802.16m is to develop an advanced air interface to meet the requirements for IMT-Advanced next generation networks while still supporting legacy 802.16 OFDMA system. This white paper will focus on some of the key features of 16m and provide comparisons to the 802.16-2009 OFDMA PHY (also referred to as 16e) with explanations of the motivations behind for the advanced features in 802.16m.

29-Jul-2010 | AN-No. 1MA167

3GPP Release 9 Technical Specification (TS) 37.141 covers multistandard radio base station conformance testing. Multistandard radio includes four standards of mobile communications: GSM, WCDMA, TD-SCDMA, and LTE. This application note introduces the concept of multistandard radio base stations as well as solutions for transmitter and receiver tests based on Rohde & Schwarz signal generators and Rohde & Schwarz signal and spectrum analyzers.

06-Jul-2012 | AN-No. 1MA198

Most of the HSDPA tests specified in the TS 34.121 for 3GPP Release-5 / -7 and -8 can be performed with an R&S®CMW500. This document provides a step-by-step guide on how to use a stand-alone R&S®CMW500 to perform HSDPA Tests (from Rel.5 up to Rel.8 / DC-HSDPA+) measurements on transmitter characteristics and receiver characteristics in line with TS 34.121 V9.5.0, clauses 5 and 6. A set of save files based on R&S®CMW500 firmware V3.0.10 for user equipment supporting Operating Band I with Power Class 4 is attached to this application note for easy recall of important settings while performing tests in line with the relevant specifications.

17-Aug-2012 | AN-No. 1CM96

1TD04 1TD04, DC/DC, Oscilloscopes The objective of this paper is to evaluate the performance of a power supply using an oscilloscope. The main measurements taken are the input frequency, output voltage, output current, and the switching frequency. Initial Evaluation of a DC/DC Switch Mode Power Supply 1TD04 1TD04, DC/DC, Oscilloscopes The objective of this paper is to evaluate the performance of a

26-Nov-2013 | AN-No. 1TD04

All models of the receiver family ESXS are equipped with a remote-control interface to IEC 625-2 (IEEE 488.2). Via this bus almost all instrument settings can be effected, measurements triggered and test results read in by the PC.

18-Jan-2002 | AN-No. 1EE05

Secure interconnection of ATC voice networks

11-Mar-2019

This application note describes how to characterize RMS jitter with the R&S FSUP signal source analyzer. The instrument can distinguish random jitter and periodic jitter easily and measure all parameters of interest. New feature: A filter function can be used for jitter calculation to simulate the frequency response of the PLL in the DUT.

05-Apr-2011 | AN-No. 1EF71

Getting EMI emissions under control is one of those tasks that R&D engineers do not enjoy doing . EMI must often be taken into consideration as early as the design phase, particularly in the case of power electronics systems with increasing switching speeds of wideband gap semiconductors. While EMI receivers or spectrum analyzers are always the preferred choice for these measurements, they are often not available as standard measurement equipment in the R&D lab. To allow optimization early on in the R&D lab, Rohde & Schwarz provides a free tool to simplify conducted emissions debugging using oscilloscopes.

27-Sep-2021 | AN-No. 1SL372

Although the commercialization of LTE technology began in end 2009, the technology is still being enhanced in order to meet ITU-Advanced requirements. This white paper summarizes these necessary improvements, which are known as LTE-Advanced.

20-Aug-2012 | AN-No. 1MA169

RMS is one of the most common parameters in test and measurement. Mathematically, it is the quadratic mean of continuously varying values (waveform). Especially when quantifying power, RMS simplifies the calculation as the polarity of the voltage and direction of the current can be disregarded.

17-Aug-2015

A new calibration method, presented by John R. Juroshek (NIST), offers fast and accurate determination of the equivalent source match of three-port devices like power-splitters and directional-couplers. The measurement result is directly displayed as normal trace on the R&S ZVM or R&S ZVK and can be stored in the most common data-formats for further processing and documentation.

13-Dec-2002 | AN-No. 1EZ51

Due to the fact that Microsoft does not maintain the Visual Studio .NET 2003 anymore Rohde & Schwarz has to use the successor compiler product Visual Studio .NET 2005 for building the test case packages. All CRTU-G customers having proprietary test case packages, developed based on Visual Studio .NET 2003, can migrate them to Visual Studio .NET 2005. This is required when the proprietary test case packages are going to be enhanced on a platform with installed Visual Studio .NET 2005.

28-Nov-2007 | AN-No. 1CM63

This application note presents the Jitter analysis capabilities of the R&S®RTO for digital signals. It demonstrates the basic operation with an application example, and shows the associated jitter analysis.

29-Aug-2013 | AN-No. 1TD03

The new R&S®DATA-NPT mobile network performance test from Rohde & Schwarz brings innovation to network performance testing. The patent-pending testing solution is a very compact and resource-saving implementation of a new measurement procedure that simultaneously measures the maximum data capacity and the minimum continuous connectivity in a mobile network.

21-Apr-2016

Fading is known from shortwave transmission, where the received field strength level may strongly vary due to atmospheric disturbances. In analog TV, the term 'fading' is practically unknown. Rather, one talks of 'antenna shadows' or 'ghost images'. The effect in question, however, is fading, ie constant reflection of the eletromagnetic waves emitted by the TV transmitter by walls of buildings, mountain slopes and similar reflecting natural or artificial obstacles. In analog TV, fading is of minor importance since the effects thereof can be eliminated almost completely through the directivity and exact orientation of the Yagi roof antenna for stationary TV reception at home. [[ br />Fading effects can also be observed in analog cable TV, for example in a block of flats linked to the cable network with one or several antenna sockets in every flat. If the taps for the sockets are not match-terminated, reflections with constant level and constant phase arise which may cause level reductions of several dB at exactly calculable points in the cable. [[ br />Moreover, the reception of TV signals broadcast via satellite can be impaired by fading. A known phenomenon is flickering of the received picture, produced by planes flying past or a drop in receive field strength caused by an approaching thunderstorm. All the above receive conditions have one thing in common: reception is stationary with a direct line of sight to the TV transmitter. [[ br />Looking at receive conditions in DVB, the effects in cable and satellite reception (DVB-C and DVB-S) are found to be similar as in analog reception. In these two modes reception is stationary, too. Terrestrial transmission (DVB-T) not only provides for stationary operation but also for portable and mobile reception. This considerably accentuates the effects of fading. [[ br />In this application note we investigate fading effects in DVB, with the emphasis on those in DVB-T signals.

06-Feb-2001 | AN-No. 7BM05

When monitoring transmission systems it is often necessary to control the monitoring equipment and to check the measurement results from a remote station. The user may also be interested to know which transmission data cause an error or violate a standard. Rohde & Schwarz offers several instruments that meet all these requirements in the field of digital TV transmission. This application note gives an overview of the design and use of a DTV monitoring system made up of the above-mentioned instruments and meeting the requirements.

15-Feb-2002 | AN-No. 7BM38

The high-definition multimedia interface (HDMI™) is used to transmit audio and video data. HDMI has become the standard for a variety of consumer electronic products, such as Blu-ray™ players, A/V receivers, set-top box, TV monitors and digital video/ still cameras. The HDMI interface measurements needed for these products require specialized T&M equipment. This equipment is not only needed for certification, but is also used for a variety of tests during development, for quality assurance and for end-of-line production testing. The R&S®VTC, R&S®VTE and R&S®VTS video testers from Rohde & Schwarz make it possible to test A/V interfaces such as HDMI easily, reliably and cost efficiently. This application note focuses on functional testing and debugging of HDMI interfaces using the R&S®VTC/VTE/VTS. It explains how these instruments can be used to assess the HDCP implementation, the ARC or the CEC functionality.

04-Jun-2014 | AN-No. 7BM85

- not available -

20-Jul-2001 | AN-No. 7BM28

1TD04 1TD04, DC/DC, Oscilloscopes The objective of this paper is to evaluate the performance of a power supply using an oscilloscope. The main measurements taken are the input frequency, output voltage, output current, and the switching frequency. Initial Evaluation of a DC/DC Switch Mode Power Supply 1TD04 1TD04, DC/DC, Oscilloscopes The objective of this paper is to evaluate the performance of a

26-Nov-2013 | AN-No. 1TD04

This document describes the typical measurements performed on mixers and how they can be implemented on the ZVA Vector Network Analyzer with the ZVA-K4 Frequency Conversion option. The document describes the concept and setups required to perform Conversion Loss, Isolation, Intermodulation and Reflection measurements.

06-May-2009 | AN-No. 1EZ58

The R&S® IQ File Cutter can load IQ data from supported IQ file formats and export part of the signal to another file. This is helpful when dealing with long measurement recordings, of which only parts are of interest and should be extracted for further analysis.

11-May-2020 | AN-No. GFM338

This application note describes how to integrate R&S®ZVA/ZVB/ZVT vector network analyzers with AWR's electronic design automation (EDA) software. Measured data can be exported using the AWR® TestWave™ tool via GPIB/LAN and verified with simulated data. Basic filter design is simplified with the AWR® iFilter™ filter synthesis wizard, an optimization tool that can be introduced to correlate measured data with simulated data.

01-Jun-2010 | AN-No. 1MA163

This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.

15-Sep-2012 | AN-No. 1MA206

This Application Note focuses on measurement of harmonics using modern spectrum analyzers. It highlights the source of harmonics before focusing on their measurement using a spectrum analyzer. The Application Note also explains the benefits of the R&S FSW’s high pass filter option for harmonic measurements.

02-Mar-2012 | AN-No. 1EF78

Remote control over a public mobile phone network with SMS or via a wireless IP connection.

22-Apr-2013

This white paper summarizes significant additional technology components based on LTE, which are included in 3GPP Release 12 specifications. The LTE technology as specified within 3GPP Release 8 was first commercially deployed by end 2009. Since then the number of commercial networks is strongly increasing around the globe. LTE has become the fastest developing mobile system technology ever. As other cellular technologies LTE is continuously worked on in terms of improvements. 3GPP groups added technology components according to so called releases. Initial enhancements were included in 3GPP Release 9, followed by more significant improvements in 3GPP Release 10, also known as LTE-Advanced. Beyond Release 10 a number of different market terms have been used. However 3GPP reaffirmed that the naming for the technology family and its evolution continues to be covered by the term LTE-Advanced. Therefore LTE-Advanced remains the correct description for specifications defined from Release 10 onwards, including 3GPP Release 12.

04-Aug-2015 | AN-No. 1MA252

With IT and OT environments converging, security concerns relating to devices and applications deployed in networked test labs, especially in T&M environments, are growing. The demands on IT security here are manifold and include, for example, remote access to in-house infrastructures, equipment rented from external providers, and the continuous deployment of devices across different time zones.

18-Oct-2022

Nearly all tests in accordance with the Bluetooth low energy test specification V4.0 [1] can be performed using the R&S®CBT alone. Some tests additionally call for signal generators to provide interference signals. This application note describes the tests performed with additional equipment and presents straightforward solutions based on the R&S®CBTgo software.

18-Jul-2013 | AN-No. 1MA200

The constantly increasing number of telecommunication services and subscribers is putting more and more pressure on the availability of already scarse frequencies. Authorities responsible for monitoring and regulating the radio traffic are confronted with more and more complex problems relating to radiomonitoring and frequency management. Without exact data - a prerequisite for monitoring existing installations and planning new services - it is impossible to solve the problem. It is essential to use the proper measurement equipment. This Application Note deals with the following measurements: Measuring various signal parameters at defined frequencies. Monitoring emissions for compliance with specified limits for field strength, modulation depth/index, frequency deviation and offset.

18-Jan-2002 | AN-No. 1EE13