To allow optimization early on in the R&D lab, Rohde & Schwarz provides a free tool to simplify conducted emissions debugging using oscilloscopes.

27-Sep-2021 | AN-No. 1SL372

R&S®RTO於EMI問題的分析與應用

Easy configuration of frequency domain analysis Easy configuration of frequency domain analysis Video, RTO2000, Oscilloscope, Responsive FFT and spectogram Easy configuration of frequency domain analysis

Russian version - времени простоя цифрового осциллографа на измерения

Russian version - Анализ джиттера с помощью цифрового осциллографа R&S®RTO

Models: R&S®RTP-K91, R&S®RTO6-K91, R&S®RTP-K93, R&S®RTP-K94, R&S®RTP-K95

How to perform signal integrity debugging on a DDR3 device Video, RTO2000, Oscilloscope, DDR3 DDR3 signal integrity debugging

The demand having a snubber circuit in the power supply topology leads to specific verification methods during the design which are the main focus within this document.

23-Jun-2021 | AN-No. 1SL363

This document is divided in two parts and starts with an introduction in AC-DC conversion principles in general. It will present the most common circuits used for different power levels. The switching mode power supply (SMPS) converter will be the main focus as they are used everywhere in the electronics. Especially the flyback converter design in different flavors are highlighted. Nevertheless, all measurements are also applicable for other SMPS converter designs operating at higher power levels.In the second part of this document, most relevant testing methods and procedures of an AC-DC converter are highlighted. For each testing section, a fundamental part will be upfront discussed and it is followed by a presentation of a suitable measurement method. In this second part, the device under test (DUT) is considered as black box device and thus the structure is similar. Therefore, the testing parts consists of methods related to input tests, output tests and a combination of both like efficiency. Of course, some test performed at the output of the converter are also relevant for DC-DC converter, e.g. the validation of the output ripple.

14-Nov-2022 | AN-No. 1SL387

Importance of deep memory in digital oscilloscopes - Rohde & Schwarz oscilloscopes offer industry-leading memory depth.

21-Mar-2017

Secondary surveillance radar (SSR) bridges the gap between communications systems and classic radar systems. Despite the increasing capabilities of mobile communications, SSR remains a major component in airspace surveillance.

17-May-2021

Oscilloscope bus decoding, RTO2000, bus decoding, I2C Dive into your protocol to check for any problems with your I²C interface.

This application note along with its corresponding white paper 1MA207 show how to use the R&S radar product portfolio to tackle test and measurement tasks in modern radar technology.

10-Aug-2012 | AN-No. 1MA127

Discover some of the key parameters of an oscilloscope and how they impact on the performance in this video series: Part 1: Bandwidth and frequency response R&S®RTO2000 Video, application videos, oscilloscope, troubleshooting, mixed signal oscilloscope R&S Talking about bandwidth Open Lightbox Talking about bandwidth

This application note summarizes the Rohde &Schwarz test solutions for LTE-Advanced (Release 10) using Vector Signal Generators, Signal and Spectrum Analyzers and the Wideband Radio Communication Tester.

03-Sep-2014 | AN-No. 1MA166

The R&S®RTO-K92 eMMC Compliance Test option offers an automated test solution for the electrical interface of an eMMC device according to the JEDEC specification, revision 5.1. Oscilloscope Application Videos, Application Video, Application Videos, Videos, eMMC Interface Compliance Test Learn how you can use the eMMC compliance test of R&S for automated testings of electrical interfaces!

RTO2000, debugging, EMI When debugging EMI problems in electronic circuits, development engineers face the challenging problem of quickly and accurately identifying and eliminating the sources of unwanted emissions. Many problems can be eliminated during development by using oscilloscopes for EMI debugging.

This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.

15-Sep-2012 | AN-No. 1MA206

This Application Note gives 10 useful Tips & Tricks for the users of Rohde & Schwarz attribute-based instrument drivers.

30-Jan-2017 | AN-No. 1MA228

Oscilloscope bus triggering, RTO2000, bus triggering, history mode, break condition Use the hardware trigger to isolate break conditions. Break conditions can be corellated with their root cause one by one using the History Mode.

Discover leading test solutions for network energy saving. Explore how to reduce RAN power consumption and increase the efficiency of Open RAN radio units.

Compliance Testing, maximum output droop, RTO, Test Mode 6 A guide to carrying out a 100BASE-T1 compliance test for the MDI return loss using an R&S®ZND 2-port vector network analyser controlled by the ScopeSuite automation software.

Based on the new high-performance R&S®SMW200A vector signal generator and the R&S®RTO digital oscilloscope, the solution provides MIMO signal generation and realtime channel emulation (up to 4x4 or 8x2) as well as synchronous analysis of multiple TX antenna signals.

RTO2000, waveform display, R&S®SmartGrid, complex measurements Use the R&S®SmartGrid function to configure the display. For complex measurement tasks where several screen displays are helpful, you can superposition windows in multiple tabs. All measurement diagrams have labeled scales so you can immediately read important signal characteristics.

Efficient analysis of power and signal integrity and EMC - Flyer

This paper describes the characterization of aluminum electrolytic capacitors specifically used in AC-DC power converter applications. It will be discussed why this capacitor technology is critical regarding lifetime and why it cannot be substituted simply by any another capacitor technology. Different aging effects of the capacitor will be discussed. Usage of the capacitor in different AC-DC converter topologies will be presented. Simulation circuits will be used to analyze the capacitor in more detail before suitable measurements will be performed to demonstrate a real example of a switching-mode power supply (SMPS).After the introduction into the aluminum electrolytic capacitor basics and theory, this paper will also present all important and possible measurements of capacitor parameters, like capacitance, equivalent series resistance (ESR) and ripple current. This includes in-circuit measurement which can be performed with an oscilloscope. An LCR-bridge is used to obtain high accuracy measurements in addition. A comparison between the two measurement methods will be presented. Furthermore, the required measurement hardware for the in-circuit measurements and the bridge measurement will be discussed and presented.Lastly, two different lifetime calculation methods are presented and a real example is used to compare the advantages and disadvantages of the different methods.Thanks to Mr. Frank Puhane from Würth eiSos GmbH & Co. KG who provided me with all aluminum electrolytic capacitor samples including the prepared capacitor with build-in temperature sensors to perform all measurements. Furthermore, his great expertise was very beneficial and helpful to create this premium application note.

07-Feb-2023 | AN-No. 1SL388

Measuring the power supply noise rejection (PSNR) requires accurate generation and leveling of artificial, sinusoidal disturbances and measurement of resulting phase-noise and jitter impairments.

30-Sep-2020

Buy more - Save more | Customize your oscilloscope configuration and save big - Flyer Brochures and Data Sheets Flyer

This white paper describes how a QAgent deployment might be handled to lessen the impact on production or lab environments.

Webinar, RTO2000, Automotive Ethernet compliance testing This webinar presents details on the individual test cases of the compliance test and provides useful information on the required test setup.