The R&S VSA and R&S UAF video analyzers have been designed for measurements on CCVS signals. Under certain conditions, they can also be used for measuring the primary colour components RGB and TV signals in the S-Video format.

21-Feb-2003 | AN-No. 7BM29E

This application note explains how to synchronize the signals from multiple R&S®SMBV100A vector signal generators in time.The synchronization of the instruments is based on a master-slave principle where one R&S®SMBV100A acts as master and supplies all necessary synchronization signals to the other instruments (slaves). The setup is simple and provides highly synchronized test signals. Time synchronous signals are needed in several applications. The master-slave setup is ideal for basic MIMO tests, certain GNSS test scenarios and WLAN IEEE 802.11ac non-contiguous channel generation. Furthermore, synchronous baseband signals are the basis for generating phase coherent RF signals with the R&S®SMBV100A.

09-Jul-2013 | AN-No. 1GP84

Development of modern EW systems is a complex and expensive process, that requires thorough testing against all requirements during all phases of development. To keep cost under control, system level testing in the lab is key and brings several advantages: test cases can be reproduced under the exact same conditions as often as necessary. System level testing in the lab is often performed in a hardware-in-the-loop (HIL) environment. This application note provides some insight into generating radar signals for hardware-in-the-loop testing with the R&S®SMW200A. An introduction to HIL testing and realtime operation of the R&S®SMW200A is given. The hardware and software interface, the PDW format and synchronization and timing mechanisms are described. Additionally, various example scenarios and detailed information about intermediate calculations are provided. The application note also provides information about system requirements for advanced PDW streaming with multiple emitters on multiple parallel streams.

22-Jan-2021 | AN-No. 1GP124

Rohde & Schwarz signal generators can generate standard-compliant WLAN IEEE 802.11ax signals for high efficiency (HE) receiver testing.This application note helps to choose the right generator test solutions and explains step-by-step how to generate 802.11ax SISO and MIMO signals. Measurements, such as EVM, are presented to illustrate the signal performance. Furthermore, this document shows how to test 802.11ax receiver specifications and the newly introduced HE trigger-based PPDU specifications according to the IEEE P802.11ax/D1.3 specification draft.

16-Aug-2017 | AN-No. 1GP115

CLGD, FSW, Applicataion Card, CATV, DOCSIS 3.1 DOCSIS 3.1 BER testing on CATV amplifiers with R&S ® CLGD and R&S ® FSW DOCSIS 3.1 BER testing on CATV amplifiers with R&S®CLGD and R&S®FSW CLGD, FSW, Applicataion Card, CATV, DOCSIS 3.1 DOCSIS 3.1 BER testing on CATV amplifiers with R&S ® CLGD and R&S ® FSW DOCSIS 3.1 BER testing on CATV amplifiers with R&S®CLGD and R&S®FSW CLGD, FSW, Applicataion Card

06-Dec-2016

The International Electrotechnical Commission (IEC) created the MBRAI specifications, which call for strict conformance tests that ensure the proper functionality of mobile receiver terminals for DVB-T/H transmissions. MBRAI is a common abbreviation of the IEC 62002 standard and stands for “mobile and portable DVB-T/H radio access interface”. This Application Note describes how the Broadcast Test System R&S®SFU provides all functions to generate MBRAI-compliant test signals. Only two special measurements require additional sources. For this purpose, the Test Transmitter R&S®SFE100 is used.

28-Nov-2007 | AN-No. 7BM61

This application note describes Methods of Implementation (MOI) for precise, fast, and error-free compliance testing of USB Type-C to legacy cable assemblies supporting USB3.1 Gen2, USB3.1 Gen1, and USB2.0. Based on 5 Gbps signaling per lane with vector network analyzers from Rohde & Schwarz.

18-Jan-2024 | AN-No. 1SL406

This application note provides basic information about settling time measurements and describes how frequency settling time measurements can be easily and convenient performed using a modern spectrum analyzer with integrated signal analysis capabilities.The analog demodulation measurement application R&S®FSxx-K7 performs frequency and phase settling time measurements using a modern wideband concept, and results are obtained easily and convenient with an integrated settling time measurement capability.

18-Jun-2022 | AN-No. 1EF112

This application note describes how to generate 3GPP (UTRA-FDD) signals for receiver tests under fading conditions for user equipment. The test setup requires an R&S®CMU200 Universal Radio Communication Tester with option R&S®CMU-B17 IQ-IF interface and an R&S®SMIQ Vector Signal Generator. The test setup can be calibrated with either a R&S®NRP-Zx USB power sensor or an NRP, NRVD, or NRVS Power Meter. To calibrate the baseband and RF path and configure performance tests according to the 3GPP test specification 34.121 easily, the program 3GFadLevCor is included.

01-Mar-2005 | AN-No. 1MA76

The Internet of Things (IoT) is considered the driving force of current and future wireless communications. In release 13, 3GPP has specified Narrowband-IoT (NB-IoT) as a new physical layer. This application note gives a short introduction to NB-IoT and shows the easy measurements with Rohde & Schwarz instruments.

30-Jun-2017 | AN-No. 1MA296

Reliable small cell planning is essential for important deployments like hospitals, manufacturing facilities, simply VIP (CxO) office floors or meeting rooms (the list of examples is endless). Often planning tools do not provide this high reliability and required accuracy.This application note is a simple step-by-step guide that introduces a practical method to perform reliable small cell planning.

09-Feb-2017 | AN-No. 1MA297

This application note offers a straightforward description of how to analyze EMI problems using the Rohde & Schwarz Oscilloscopes. The discussion begins by covering the basic mechanisms that can result in unwanted RF emissions and then describes how to proceed in analyzing EMI problems. Finally, a practical example is given to illustrate the analysis process.

25-Jun-2014 | AN-No. 1TD05

This application note describes the different memory types and locations that user information can be stored in a spectrum analyzer R&S® FSP, R&S® FSU or R&S® FSQ, as well as the different ways in which it can be erased/cleared for security reasons.

20-Sep-2004 | AN-No. 1EF53

The R&S®FPS-K18 amplifier measurement option in combination with the R&S®FPS signal and spectrum analyzer and the R&S®SGT100A SGMA vector RF source enables high-speed amplifier characterization.

13-Jun-2016

From designing a test setup to performing accurate measurements

Double-Pulse testing is a standard test-method used in power electronics design. Accurate measurements require a careful design of the test setup and the selection of the right measurement instruments. This application note discusses important aspects of double-pulse test setups as well as how to perform accurate measurements.

22-Mar-2021 | AN-No. GFM347

For NB-IoT applications to function correctly, sufficient network coverage is required. Coverage must be measured to ensure a robust NB-IoT connection. Rohde & Schwarz mobile network testing provides a unique combined test solution that accurately measures the DL coverage using network scanners. It measures the device/network interaction, UL behavior, protocol, signaling load and energy efficiency during communications using NB-IoT devices connected to R&S®ROMES.

20-Feb-2018

10BASE-T1S Ethernet enables the integration of diverse sensors into an automotive-Ethernet vehicle supply system, for example short-range radar sensors for detecting blind spots or ultrasonic sensors for the parking assistant. For reliable operation of the functions, data transmission over 10BASE‑T1S Ethernet must be assured at all times and in every climatic environment. Functionality must be tested during development and in production. Only 10BASE-T1S Ethernet interfaces that have passed compliance testing in line with IEEE 802.3cg can be deployed in vehicles. Consequently, vehicle manufacturers and their suppliers need measuring equipment that allows them to perform these tests quickly and reliably.

15-May-2020

Make more accurate power rail measurements.

17-Jul-2018

PAM-4 (4-level pulse amplitude modulation) has been introduced in high-speed serial data technology to reduce the bandwidth demands of ultra-high data rates. It uses only half the bandwidth per bit that would be required of conventional NRZ (non-return to zero) modulation. But at the same time, PAM-4 signaling complicates design and test at every turn. Evaluation of channels is now just as important to system development as serializer / deserializer (SerDes) testing and the challenges presented require a higher level of test and measurement performance than ever before. This paper investigates the evaluation complexities of PAM-4 interconnects at high data rates.

22-Oct-2020 | AN-No. GFM355

The compact R&S®CMA180 Radio Test Set allows straighforward tests on devices that use analog or digital modulation and demodulation formats. This application note focusses on the use of the digital radio capabilities for measurements on radio transceiving devices in terms of their functionality and parameter characterization. Also shown is how to use the instrument with the various software tools available from Rohde & Schwarz for creating and evaluating digitally modulated signals. Various software examples are provided as free download along this paper. This application note addresses readers who develop, produce or optimize digital radio transmitting and receiving devices or maintain analog radio communication equipment alongside those with digital modulation.

10-Feb-2017 | AN-No. 1MA277

Using VISA (Virtual Instrument Software Architecture) several interfaces allow communication between your computer and instruments. This application note describes the usage of both - R&S® VISA- NI VISA running on Microsoft Windows 10™ with the following connection types: ► USB VCP (Virtual Com Port), also called USB CDC (Communications Device Class) ► USB TMC (Test and Measurement Class)► Ethernet Raw Port Socket► Ethernet in general e.g. VXI11 or HislipAll the examples are shown using the R&S® HMC8042 unless otherwise stated. There may be some difference when integrating other devices. As example some interface types are not available on every unit.This application note does not claim to be complete. All information has been compiled with care. However, errors can’t be ruled out.

28-Oct-2021 | AN-No. 1SL374

Power Added Efficiency (PAE) is a key parameter for the characterization of an amplifier.This application notes introduces two alternative methods how to do the Power Added Efficiency measurement. The first one is based on the R&S ZNB vector network analyzer (VNA) measurement function. Alternatively to this, the PAE tracer macro is introduced. This macro offers to make the PAE at an user selected compression point of the amplifier versus frequency. The PAE tracer macro is provided together with this application note.

22-May-2013 | AN-No. 1EZ64

The R&S®CMP200 radio communication tester together with the R&S®CM-Z300A time of flight kit provides an accurate setup for time of flight measurements – in validation, calibration and certification.

27-Jul-2022

This white paper provides a brief technology introduction on the 802.11ac amendment to the successful 802.11-2007 standard. 802.11ac provides mechanisms to increase throughput and user experience of existing WLAN and will build on 802.11n-2009.

23-May-2012 | AN-No. 1MA192

This application note introduces the reader to the SpaceX Hyperloop Pod Competition project and their special demands for the electrical drive train. Common motor technology like brushless motors and their typical control methods widely used in the industry are also discussed within this document.However, the main focus of this paper is a demonstration of a power measurement method of a three-phase inverter by means of a 4-channel oscilloscope. Not only the theory of the power measurement is presented but also the conducted measurement is presented including tips and tricks to obtain the best measurement results.The measurement solution provided by Rohde & Schwarz was mandatory for the TUM Hyperloop team to overcome challenges in optimization of the electrical drive train used in the SpaceX Hyperloop Pod Competition project.Many thanks to Mr. Johannes Ungar and Faruk Centinkaya (TUM Hyperloop) for contributing significantly to this application note. By combining their expertise in electrical drive trains used in the Hyperloop Project and with a Test & Measurement solution from Rohde & Schwarz, we have achieved synergies that will be beneficial for any design and test engineers in the industry.

31-Mar-2021 | AN-No. GFM360

This application note is intended as a guide to configuring the R&S®CMU200 instrument for CDMA2000 1xEV-DO / 1xRTT Hybrid Mode testing.

01-Oct-2007 | AN-No. 1CM65

R&S®CMWcards, an intuitive and user-friendly software application, makes it possible to recreate field testing in a lab environment

19-Feb-2019

Emergency Road Assistance (ERA-GLONASS) is a service provided in the Russian Federation with thegoal of reducing response times for accidents or other emergencies on the roadways. This application note briefly describes the technology behind ERA-GLONASS and presents conformance tests for ERAGLONASS using the R&S®CMW500 RF tester and the R&S®SMBV100A vector signal generator. A Test software for ERA-GLONASS makes it quick and easy to perform these tests with the GSM or WCDMA wireless communications standard. It also shows a test solution for GNSS performance tests for ERAGLONASS using the R&S®SMBV100A vector signal generator and the option R&S®SMBV-K360 together with CMWrun.

24-Jan-2018 | AN-No. 1MA251

The R&S®SMB100A analog signal generator is the ideal calibration source for weather radar receivers due to its highly accurate output level.

25-Jan-2011

ZVR is a vector network analyzer equipped with selective input channels for determining phase relations. Thus a wide dynamic range can be obtained. For measurements on frequency-converting DUTs (output frequency not identical to input frequency), the generator and receiver frequency ranges can be separately set. For measurements on DUTs using a built-in conversion oscillator, as is the case here, the conversion frequency must be exactly known so that the receiver can be accurately tuned to the respective output frequency. The maximum receiving bandwidth is 26.5 kHz. When a wide dynamic range is required, this bandwidth has to be reduced with the consequence that the requirement for the DUT output frequency and the ZVR receive frequency to be in agreement will be greater.

04-Aug-1998 | AN-No. 1EZ31