This application note discusses the use of the WOOSHCOM® DHEI output interface adapter (model 3010), which converts the transport stream from DHEI format into DVB-ASI. Further processing and analysis of the transport stream signal then becomes available with any of the Rohde & Schwarz Test & Measurement instruments. It also describes how to extract an unencrypted transport streams out of a Motorola IRT.

08-Jun-2004 | AN-No. 7BM40

This application note outlines two different approaches for remote-controlling Rohde & Schwarz instruments out of MathWorks MATLAB:The first one uses VISA connection and direct SCPI commands.The second approach takes advantage of Rohde & Schwarz VXI plug&play instrument drivers and MATLAB Instrument Control Toolbox.

12-Jun-2017 | AN-No. 1MA171

Load pull is a powerful method for characterizing RF power amplifiers through impedance variation. Load pull enables model extraction and validation as well as performance, ruggedness and efficiency testing.

02-Sep-2020

This application note examines both the theory and practice of state-of-the-art spectrum analysis by discussing specific measurements taken on an integrated RF amplifier.The theoretical portion of this document first describes how modern spectrum analyzers are designed and how they work. That is followed by a brief characterization of today's signal generators, which are needed as a stimulus when performing amplifier measurements. The effects on the spectrum that are caused by the nonlinearity of real devices under test are derived mathematically.The practical portion of this application note contains detailed test and measurement tasks that are suitable for use as lab exercises performed in small groups. The purpose of these tasks is to illustrate the explanations provided in the theoretical section and to provide a deeper understanding of the principles explained there.

05-Mar-2013 | AN-No. 1MA201

Simultaneous simulation of all important constellations and frequency bands makes the GNSS simulator in the R&S®SMW200A the perfect solution for testing your GNSS receiver in the lab.

11-Sep-2018

The option ZVR-B7 allows an enhanced power calibration of the source and of the receiver channels of a ZVR, then being active instead of the standard factory power calibration. Using an external power meter, the power level of input or output wave quantities will be adjusted to a desired value at an arbitrary reference plane.

29-Jul-1998 | AN-No. 1EZ41

This application note describes how to use the mask and limit test features of the R&S®RTO, R&S®RTE and R&S®RTM Digital Oscilloscopes for EUT monitoring of signal forms, jitter etc. with the R&S®EMC32 Measurement Software. The mask test function allows autonomous characterization of digital signal integrity during EMS tests. R&S®EMC32 software records violations of userdefined limits or mask templates and evaluates the immunity threshold at frequencies of critical electromagnetic susceptibility.

20-Apr-2015 | AN-No. 1MA242

The hardware-in-the-loop options for the R&S®SMBV100B and the R&S®SMW200A GNSS simulators enable realistic, cost-efficient and flexible testing in a user-controlled environment.

03-Jun-2019

High throughput is the key production metric for efficient operation. Improving test speed helps reduce the cost per device. The R&S®PVT360A performance vector tester is optimized for high speed production tests.

12-Apr-2023

This application note provides a summary of the current test solutions available with Rohde & Schwarz equipment. The opportunities provided by the individual devices are presented briefly and a demonstration using a spectrum analyzer and a vector signal generator is described.

14-Sep-2009 | AN-No. 1MA112

Its dual-path concept plus its ability to duplicate baseband signals make the R&S®SMW200A vector signal generator ideal for efficient GSM/EDGE AMsuppression conformance testing.

28-Feb-2017

Air Traffic Control (ATC) radar, military Air Traffic Surveillance (ATS) radar and meteorological radar operate in S-Band frequency range. In fact 4G communication systems such as Long Term Evolution (LTE) make also use of these frequencies. Test and measurement of their coexistence is absolutely essential as performance degradation of mobile devices and networks and even malfunction of ATC radars has been proven.This application note describes LTE and S-Band radar coexistence test and measurement. It addresses LTE user equipment, base stations and S-Band radars and presents test solutions.

28-Mar-2014 | AN-No. 1MA211

The present R&S®SMW-K506 Interface Control Document contains information on► the R&S descriptor word format, including ARB descriptor words and control descriptor words in deterministic and instant mode► Timing requirements and limitations of the interface► Properties of the network interface (Connector designation: HS DIGIQ).It is intended for use by customers using descriptor words to control the R&S®SMW200A in real-time. The interface control document specifies the interface between the customer’s hardware used for provision of descriptor words and the R&S®SMW200A HS DIGIQ interface. Additional information on descriptor word processing inside the R&S®SMW200A is provided.

17-Mar-2022 | AN-No. 1GP134

Its high measurement speed makes the R&S®EVS300 level and modulation analyzer ideal for reliable ILS runway measurements at maximum speed.

16-Dec-2015

GSM standard 11.10 prescribes a number of tests requiring measurements on mobile stations under multichannel conditions (fading). The combination of Radiocommunication Tester CRTP02 or CRTC02 and Signal Generator SMIQ allows cost-effective performance of the most important fading tests, in particular the tests according to sections 13.2, 14.2 and 14.3 of GSM 11.10. The aim of this application note is to familiarize the user with all the capabilities offered by the above combination of measuring instruments. The user should then be able to quickly generate and run his own fading tests using the IEC/IEEE-bus control commands described in this application note. To facilitate reading of the following, the testers CRTP02 and CRTC02 are referred to as CRTx.

07-Nov-1997 | AN-No. 1MA02

This Application Note describes signal generation with carrier aggregation for 802.16m based on 802.16e signals in practical important configurations using one or more Vector Signal Generators R&S SMU200A or R&S SMBV100A. Various examples illustrate how to analyze these signals using the Vector Signal Analyzer R&S FSQ, R&S FSG or R&S FSV.

22-Mar-2010 | AN-No. 1MA173

Noise figure is an important parameter that describes the noise contribution of an electronic device. A classical approach to measure the noise figure is to use a noise source which delivers two different input noise powers by switching between a “hot” and a “cold” state and a noise receiver (e.g. a spectrum analyzer).In contrast to this approach, using a vector network analyzer with the “Cold Source” approach eliminates the need for a noise source. A cold source noise power measurement followed by an available gain measurement of the device under test is sufficient to determine the noise figure of the device. This application note describes the “Cold Source” technique for measuring noise figure on the R&S®ZNA family of vector network analyzers.Background equations are provided for an analysis of noise factor, noise figure and noise temperature on a device under test and a cascade of devices.Based on a measurement example the user will be guided through the process of setting up a noise figure channel and performing a noise figure measurement. In addition, various measurement options are reviewed, providing guidance as to when and how each option should be utilized to improve the noise figure results.

23-Dec-2021 | AN-No. 1SL378

With a Rohde & Schwarz oscilloscope

31-Dec-2018

EMI debugging, FPC, FPC1000, FPC1500, EMC compliance test, EUT The combination of high power and current being sharply switched on and off has a lot of potential for EMI. EMI debugging a switched-mode power supply with R&S®FPC1000/ R&S®FPC1500 EMI debugging, FPC, FPC1000, FPC1500, EMC compliance test, EUT The combination of high power and current being sharply switched on and off has a lot of potential

30-Jun-2019

Adjacent Channel Power performance of power amplifiers used in digital TV systems has to be guaranteed over a wide frequency range, 54 to 890 MHz, which may lead to time consuming test procedures. The application software described here provides swept ACP analysis, using AMIQ and SMIQ for signal generation and FSP, FSU or FSE for signal analysis. ACP measurement is performed according to FCC Regulation 47CFR 73.622(h).

16-Oct-2001 | AN-No. 1MA43

FSxRecordPlay is a program for recording the trace data in frequency and time domain from Rohde & Schwarz spectrum analyzers and measurement receivers via IEEE bus, LAN/Internet or internal remote control connection. The stream waveform data can be played back and analyzed directly in this software with variable speed.

20-May-2010 | AN-No. RAC-0605-0004

radio signals, automatic monitoring, interference, RF radiation, frequency spectrum, Automatic monitoring of radio signals interfering with sensitive devices in hospitals Automatic monitoring of radio signals interfering with sensitive devices in hospitals radio signals, automatic monitoring, interference, RF radiation, frequency spectrum, Automatic monitoring of radio signals interfering with sensitive

04-Sep-2006

During development of MU-MIMO antenna arrays, the beamforming algorithms undergo steady revision. Whether used in regression testing or verification of newly introduced features, fast beamforming verification helps to speed up R&D for beamforming antennas and improve performance of your product.

07-Jul-2020

This application note describes how to generate the noise field for ambient noise rejection tests according to 3GPP TS 26.132, sections 7.9 and 8.9.

12-Oct-2010 | AN-No. 1GA51

A measurement campaign quantifying the impact of intermodulation in 5G TDD networks

Critical infrastructure: With the deployment of TDD networks, the mobile network community recognizes the critical importance of cell synchronization and the use of uniform TDD patterns across different networks for the proper operation of mobile radio networks. Variety of scenarios: Possible scenarios include cross-border situations, interactions between private campus networks and public mobile networks, and accidental synchronization chain breaks or misconfigurations within the mobile network.Measurement techniques: To quantify the effects of non-synchronized cells and using different TDD pattern in neighboring networks, R&S, in collaboration with TU Dresden and Advancing Individual Networks GmbH (AIN), conducted a measurement campaign using movable networks with full control over all network parameters. This campaign measured the effects on uplink and downlink throughput, mapping these to RSSI/RSRP values received at the interfered site.Customer benefits: The available quantification is valuable for predicting and assessing potential interference scenarios before setting up and operating a new cell site.

11-Sep-2024 | AN-No. 8NT18

This Application Note describes measurements compliant with the CDMA2000 base station standard described in 3GPP2 C.S0010-C v2.0 / TIA/EIA-97-F-1. The primary focus is on solutions for generating and analyzing CDMA2000 signals. The special characteristics that make the selected signal generators and signal analyzers highly suitable for this purpose are detailed, and remote control programming is demonstrated by means of a free-of-charge program.

15-Sep-2009 | AN-No. 1MA109

This application note highlights various aeronautical radio navigation signals such as VHF omnidirectional radio range (VOR), instrument landing system (ILS) for glide slope (GS) and localizer (LLZ), as well as marker beacon (MB). Rohde & Schwarz test and measurement solutions for avionics navigation equipment are introduced based on application scenarios, including calibration, research and development, field tests, and transceiver testing.

01-Feb-2012 | AN-No. 1MA193

The converters offered for the R&S®ZVA family extend the network analyzers' frequency range up to 325 GHz. This Application Note describes typical measurements on millimeter-wave mixers and millimeter-wave frontends. It also discusses a signal identification method that enables spurious measurements to be performed in the millimeter-wave range using an R&S®ZVA network analyzer in conjunction with a converter.

17-Nov-2008 | AN-No. 1EZ57

Phase distortions in a transmission channel are determined using group delay measurements, they must be as low as possible to maintain good signal quality. Vector network analyzers are normally used to characterize the group delay variations as a measure of phase distortion.This application note provides basic information about the concept of a group delay measurement with spectrum analyzers and signal generators, and how this method simplifies the test setup and improves the measurement speed.Measurement examples show the limiting factors of this approach and help the user to understand and avoid some limitations of this method. In addition the test results are compared to those generated with vector network analyzers.

09-Aug-2017 | AN-No. 1EF98

Vector Network Analyzers (VNA) are gaining popularity in the Signal Integrity community as time domain measurement and analysis tools. VNAs with 8 ports or more can provide significant decreases in test time by migrating from a 4-port measurement system to an 8-port measurement system. For tight tolerance DUTs that are barely within the test limit lines, small increases in accuracy can be realized by testing all of the test parameters at once, because the entire test setup is at the same temperature. This application note discusses the thermal advantages of testing an 8-port DUT with the R&S ZNBT VNA. The use of the ZNBT to assess and debug two differential pairs in a 20-inch backplane is presented.

18-Mar-2020 | AN-No. 1EZ83_0E