The R&S®CMW-B400B audio board offers the flexibility to measure and quantify audio applications with the R&S®CMW270/280/500 radio communication testers.

20-Jun-2013

The R&S®FPS-K18 amplifier measurement option in combination with the R&S®FPS signal and spectrum analyzer and the R&S®SGT100A SGMA vector RF source enables high-speed amplifier characterization.

13-Jun-2016

This application note describes the configuration of a Miracast wireless video transmission system and how to measure the delay times between a smart phone or tablet (source) and a television / monitor (sink) display. The accompanying software for Windows 7/8/10, Mac OS X 10.x and MATLAB additionally allows to measure the delay until the video signal is transmitted over the air and optionally until it is available on the HDMI cable of an external Miracast receiver.

01-Oct-2015 | AN-No. 1MA250

A key challenge for embedded devices with DDR memories is to maintain signal integrity in the presence of power and ground rail fluctuations. This becomes even more important as supply voltages decrease and switching speed increases leading to tighter power rail tolerances and jitter requirements.

05-Apr-2017

From designing a test setup to performing accurate measurements

Double-Pulse testing is a standard test-method used in power electronics design. Accurate measurements require a careful design of the test setup and the selection of the right measurement instruments. This application note discusses important aspects of double-pulse test setups as well as how to perform accurate measurements.

22-Mar-2021 | AN-No. GFM347

This document answers frequently asked questions regarding Rohde & Schwarz Broadband Amplifiers. It describes remote operation and monitoring of the R&S® Broadband Amplifier series through a standard web browser.

04-Nov-2016 | AN-No. 7TA1

Antennas have become an integral part of consumer electronics, even in small portable devices that rely on an energy source with limited capacity. Consequently, antennas need to be physically small and power efficient.

05-Mar-2020

Frequency converters e.g. in satellite transponders need to be characterized not only in terms of amplitude transmission but also in terms of phase transmission or group delay, especially with the transition to digital modulation schemes. They often do not provide access to the internal local oscillators. This application note describes a method using the R&S®ZNA analyzer family to measure group delay of mixers and frequency converters with an embedded local oscillator very accurately. The key aspect of this new technique is that the network analyzer applies a 2-tone signal to the frequency converter. By measuring the phase differences between the two signals at the input and at the output, it calculates group delay and relative phase.

11-Jul-2019 | AN-No. 1EZ81

The purpose of the test setup described is to ensure or to enhance the level accuracy of signal generators or the generator part of communication testers. The level accuracy of test signals is particularly important at low levels when measuring BER level sensitivity at digital communication receivers. The highly linear FSP spectrum analyzer is used in combination with a power meter to get the best possible accuracy with high measurement speed over a very wide level range.

18-Feb-2011 | AN-No. 1MA21

An ever-increasing requirement for data on mobile networks, driven by a myriad of applications from HD video on the move to autonomous vehicles and Industrial IOT, means a part of the new 5G network is to be deployed at mmWave frequencies, with a 26 GHz pioneer band defined for the UK between 24.25 - 27.5 GHz.This near 10-fold increase in frequency over 4G networks opens several challenges, both in the design and implementation of the required sub-components, network infrastructure and end user equipment, and in parallel in the test and measurement approaches used to drive these developments.In this presentation, we will introduce some of the main challenges in test and measurement of a device at these frequencies. We will then present the testing of a 26-28GHz pioneer band dual channel amplifier evaluation module using 5G NR test waveforms.

26-Nov-2018

In the satellite sector, components, subsystems and entire satellites must be qualified in a thermal vacuum chamber before they can be used in space. This qualification proves that equipment can not only survive but also function in the harsh conditions encountered during launch and in space.

05-Oct-2022

VCS-4G, secure Communications, VoIP, air traffic contro, EUROCAE, ED‑137, ATC, CERTIUM, CERTIUM VCS test system Rohde & Schwarz solution CERTIUM VCS CERTIUM VCS test system for aircraft manufacturers VCS-4G, secure Communications, VoIP, air traffic contro, EUROCAE, ED‑137, ATC, CERTIUM, CERTIUM VCS test system Rohde & Schwarz solution CERTIUM VCS CERTIUM VCS test system for aircraft manufacturers VCS

01-Aug-2023

Level or power measurement of especially modulated signals using spectrum analyzers is becoming more and more important . Whereas the first choice in terms of accuracy for power measurement of any carrier (modulated or non-modulated) is a power meter, power measurement of spurious or in the adjacent channel of a transmission system needs a selective power meter with high dynamic range. A power meter, however, is a non-selective device with limited dynamic range and is not appropriate for these types of measurements. The first choice is a spectrum analyzer because of its versatile use as a general-purpose instrument. Compared to a power meter its power measurement accuracy is worse. In general this can be overcome by substitution methods using a power meter, an attenuator and a signal generator. But substitution is time-consuming and requires more investment in test equipment than a single instrument. Therefore it is most important to have a spectrum analyzer like the FSE, which can fulfill at least most of the requirements in terms of measurement accuracy.

13-Jan-1998 | AN-No. 1EF36

5G networks will need to offer more capacity and flexibility while lowering the operational expenses of the system. Two new technologies can simultaneously address both the increase in capacity and the increase in energy efficiency: Virtualization & Massive MIMO. This white paper provides an overview of test solutions addressing current and future requirements for antenna verification including both conducted and over-the-air (OTA) test methods, which result from applying Massive MIMO antenna technology.This white papers complements the white paper (1MA276) from Rohde & Schwarz, which introduces fundamental theory behind beamforming antennas and provides calculation methods for radiation patterns, a number of simulation results as well as some real world measurement results for small linear arrays.

11-Nov-2016 | AN-No. 1MA286

The R&S®Pulse Sequencer software offers an easy way to simulate moving radar emitters and a moving receiver for EW receiver tests. The software together with the R&S®SMW200A vector signal generator is a powerful radar simulator. It enables engineers to generate highly dynamic 3D scenarios in the lab.

18-Sep-2018

The ‘Data Reduction’ sequence step is an essential part of an EMI Auto Test since it evaluates the relevant frequencies at which the final measurements are to be done. The intention of this application note is to make the data reduction data flow more transparent (contents of input and output tables) and how the parameters (location and relations) influence the evaluation algorithm.

16-Nov-2011 | AN-No. 1SP02

R&S®CMWcards is an intuitive and user-friendly software application that makes NB-IoT OTDOA positioning design verification easier than ever.

26-Nov-2018

Application Note 1MA81 has been replaced by .

05-Jan-2012 | AN-No. 1MA81

This Application Note describes how to perform measurements on power amplifiers for TD-SCDMA base stations to specification TS 25.142 using Rohde & Schwarz generators, power meters and signal/spectrum analyzers. The TD-SCDMA application firmware for Rohde & Schwarz generators and analyzers as well as their outstanding performance facilitate efficient and rapid measurements.

31-Jul-2007 | AN-No. 1MA103

This Application Note describes two programs for calculating conversions: 1.: The Power Unit Calculator Power, dBm, dBmV and Volts @ 50 W 2.: The VSWR Calculator Reflection, VSWR, Return loss and Power reflection Reflections, Reflectionl to Mismatch Uncertainty.

03-Jul-1998 | AN-No. 1MA12

Today’s infotainment units offer a wide range of features to truly embody the concept of the connected car.

14-Jun-2018

This application note describes the procedure used to create LabVIEW driver libraries by importing *.DLL files from the GTSL (Generic Test Software Library) development framework for the R&S CompactTSVP. This common recipe allows all upcoming versions of the GTSL to be imported as well, for seamless deployment of R&S CompactTSVP modules.

28-Dec-2007 | AN-No. 1SP801

DOCSIS has become the established standard for return channels when it comes to implementing interactive services in broadband cable networks. The quality of these signals is essential to network efficiency. The analysis can be done using the highprecision R&S®ETL, R&S®EFA and R&S®FSH3-TV TV test receivers that have proven themselves in the downstream. These T & M instruments can be quickly and easily configured for measuring the upstream.

13-Jul-2012

Wireless coexistence testing

11-May-2020

DVB-T Bursted Noise is a tool for generation of DVB-T compatible noise signals. The IQ data can tranferred to WinIQSIM™ / WinIQSIM2™ for further processing and transmission to an AMU, AFQ, AMIQ, SMU, SMIQ.

08-Jul-2009 | AN-No. 1MA51

A step by step HOW TO guide to perform manual and automated wireless coexistence testing

At the end of the year 2020, there were over 20 Billion internet of things (IoT) products in the world operating using the licensed and unlicensed frequency bands. This growth trend is projected to keep steady over the coming years as more and more people adopt to a smarter and more connected lifestyle. This will result in a much busier and challenging RF environment than the one we have today. In order to understand the complexity of the RF spectrum, a white paper was published in 2021 from Rohde & Schwarz, which featured RF spectrum activity at multiple locations observed at different times of the day. The locations were selected based on population densities and the amount of known RF transmitters & their frequencies at those locations. It was also concluded that the ISM bands on average have higher channel utilization since most IoT devices take advantage of the unlicensed spectrum. The paper recommended, that while performing wireless coexistence testing, the test conditions should reflect the operational RF environment that the device is intended to operate in. Otherwise, the characterization of RF performance would only reflect ideal case which doesn’t exist in real world operation. Since it is not always possible to test all devices in the real world, relevant test methodologies need to be setup to replicate the real world as much as possible.This will help us get a better understanding of how the receiver of the RF device will behave under different RF conditions. It is also recommended to perform measurements in order to understand the behavior of the device in the future when the spectrum will get even more challenging. Therefore, a through characterization of the capability of the RF receiver to handle in-band and out-of-band interference signals in also of interest.In terms of regulatory compliance requirements for ensuring wireless coexistence performance, the ANSI C63.27 is currently the only published test standard that provides guidance on how to perform coexistence testing on devices. The test complexity is based up on risk imposed on the user’s health in the event of a failure caused by an or a plurality of interference signal. The standard also gives device manufacturers guidance regarding test setups, measurement environments, interference signal types and strategy, performance quality measurement parameters for physical layer using key performance indicator (KPI) and application layer parameters for end-to-end functional wireless performance (FWP).In this application note, the guidance provided by the ANSI C63.27-2021 version regarding test setup, measurement parameter and interference signal have been followed. It will give the reader a clear idea on how to configure standardized test instruments from R&S in order to generate the wanted signal as well as unintended interference signals and conduct measurement to monitor device performance in terms of PER, ping latency and data throughput.This application note provides step-by-step instruction on how to perform measurements using conducted and radiated methodology. Both manual and automated instrument configuration approach is explained in this document.The automation scripts are written using python scripting language and are available for download with this application note, free of charge. Official required to run the scripts are available on the PYPI database.

10-Nov-2022 | AN-No. 1SL392

automotive radar echo generator, AREG100A, automotive radar sensors Automotive radar sensors are safety-relevant and have to be comprehensively tested for reliable functioning. The R&S ® AREG100A automotive radar echo generator is a versatile instrument for stimulating radars in the 24 GHz ISM band and in the 77 GHz and 79 GHz frequency bands. Together with the R&S ® ATS1500A shielded chamber, it offers

06-Aug-2018

Gated mode measurements in private 5G networks

11-Apr-2024

The R&S®FSW signal and spectrum analyzer is a high-performance instrument capable of measuring many key system and component parameters. Using the bit error rate (BER) functionality of the R&S®FSW-K70P option, the raw data error performance of a component or system can be accurately determined.

26-Sep-2018

FSH4Remote is a free-of-charge program for connecting the R&S®FSH4/8 handheld spectrum analyzer or the R&S®FSC spectrum analyzer to a remote computer, and for providing remote control of the functions from the computer. It runs under Windows and Linux operating systems. This application note describes the easy use of FSH4Remote to control the R&S®FSH/FSC and read the trace.

09-Feb-2012 | AN-No. 1MA180