Batteries are dynamic energy sources that diverge from ideal voltage sources. The R&S®NGM-K106 battery simulation option recreates battery models on the R&S®NGM200/NGU201 does far more than standard models.

02-May-2023

The sweep tool has several R&S®NGU source measure unit functions for characterizing semiconductors.

02-May-2023

This application note reviews a new calibration subsystem which consists of Inline Calibration Units (ICUs). These ICUs are designed for in situ use, so they are left in place both during the calibration procedure and during the measurement of the Device Under Test (DUT).This adds versatility, convenience and accuracy to the VNA based measurement system, as it means the calibration can be refreshed at any time without manually disconnecting the DUT from the test system.

29-Sep-2017 | AN-No. 1EZ71

Modern mobile phones can support cellular and noncellular wireless communications standards at the same time. This means, however, that the subsystems must operate in very close proximity to each other within a single device (in-device coexistence). The resulting high level of reciprocal leakage can at times cause considerable interference.This application note employs preliminary theoretical analysis and demonstrates how the problems of indevice coexistence can be measured. For german version please visit .

28-Apr-2015 | AN-No. 1MA255

Energy efficiency of RF Frontends (RFFE), especially transmitters, continues to gain greater prominence.Meeting the efficiency challenge is increasingly difficult at higher operating frequencies and bandwidths, such as those proposed for 5G.There is a group of transmitter RFFE architectures whose signal output is constructed from two, or more, efficiently generated components. This signal construction in effect, means that such architectures use predictive, post-correction linearization. Their predictive nature enables distortion to be completely eliminated.The capabilities of multi-channel signal synthesis setups with R&S®SMW200A, in combination with the R&S®FSW analyzer enable measurement, hence development, of these types of transmitters.The document focusses on devices for the 3.5 GHz NR (5G New Radio) candidate band, but its findings are equally applicable to developments and measurements for, for example, K-band satellite applications or mmW NR candidate bands, where efficiency is an even more crucial design target.

01-Aug-2017 | AN-No. 1MA289

The aim of this application note is to provide information regarding Rohde & Schwarz instrument drivers. This paper shall help application engineers and software developers to easily get an understanding of advanced techniques to develop test and measurement (T&M) applications by utilizing Rohde & Schwarz instrument drivers. Furthermore the nomenclature used for Rohde & Schwarz instrument drivers will be explained.

01-Jan-2013 | AN-No. 1MA153

The MFIA impedance analyzer – a multipurpose instrument for R&D and quality control – can be used to measure the ESR and ESL of DC-link capacitors over a wide frequency range.

04-Sep-2024

This application note describes how to set up 3GPP FDD and LTE multicell and multi-UE scenarios with the R&S®SMU200A with a focus on routing and leveling of the baseband signals. Furthermore, it describes in detail how to determine the correct AWGN settings, i.e. how to calculate the required signal-to-noise ratio for the various scenarios.

10-Aug-2011 | AN-No. 1GP80

This application note provides a guide through the measurements for IEEE 802.11ac WLAN transmitter signals using the general purpose OFDM analysis software R&S FS-K96. Step-by-step instructions for performing the measurements are provided and the different result types available with the FSK96 Software are discussed.

22-Sep-2011 | AN-No. 1EF82

Three hardware modifications of the option External Measurements ZVR-B25 enable the bidirectional network analyzers of the ZVR-family to carry out 4-port measurements. For the measurements, the four ports PORT 1, PORT 2, INPUT b1 and INPUT b2 at the front panel of the ZVR(E) are utilized. The fifth connector, ie OUTPUT a1, is not required for this purpose. As detailed below, the necessary modifications of the test set of the analyzer are described for the model ZVR. Of course, the modifications can be done in a similar way for the model ZVRE as well.

28-Jul-1998 | AN-No. 1EZ25

Near Field Communication (NFC) is a new short-range, standards-based wireless connectivity technology, that uses magnetic field induction to enable communication between electronic devices in close proximity. Based on RFID technology, NFC provides a medium for the identification protocols that validate secure data transfer. NFC enables users to perform intuitive, safe, contactless transactions, access digital content and connect elec­tronic devices simply by touching or bringing devices into close proximity. This White Paper gives an overview of NFC uses, NFC technology and signals and RF measurements on NFC units. NFC analog measurements with R&S test instruments are described in detail in R&S application Note 1MA190 'Basic Tests of NFC Enabled Devices Using R&S Test Equipment'

03-Jun-2013 | AN-No. 1MA182

Sporadic events and errors may occur when developing new measurement instruments and need to be taken into account in all design stages and analyses. The Rohde & Schwarz power supplies can precisely capture such sporadic events and errors.

02-May-2023

This application note provides information about measurements on DVB-S2 transmitters, including Amplitude Phase Shift Keying (APSK) signals. Specifically, this note will discuss how to import APSK mapping files in order to make modulation quality measurements.

09-Feb-2010 | AN-No. 1MA172

The R&S®QPS quick personnel security scanner transforms people-screening technology with its high-performance, fully electronic and solidstate flat panel design that has no moving parts. The R&S®QPS improves the security screening experience and operations by having a simple open design for a spacious screening environment and unobstructed view for security personnel, making high-resolution people screening more comfortable and efficient than ever before.

15-Apr-2019

This application note explains how to convert different Rohde & Schwarz I/Q file formats among each other using the supplied software tool.

23-Sep-2015 | AN-No. 1EF85

Fading in the baseband of the R&S®SMW200A signal generator is well proven and widely accepted for testing any mobile radio standard. However, there are applications where an RF signal must be faded.A versatile RF Fading Simulator can easily be built using an R&S®FSW, R&S®FSQ, R&S®FSG, R&S®FSV signal analyzer with Digital Base Band Interface or with the instrument combination R&S®TSMW / R&S®IQR and an R&S®SMU signal generator with digital baseband inputs and fading simulator option. Note describes how.

27-Feb-2015 | AN-No. 1MA145

The test case wizard enables the signal generator to set up all required parameters for conformance testing of 5G NR base stations in no time with just a few clicks.

25-May-2021

The antenna patterns of automotive radars provide a wealth of information that is of vital importance during radar development and validation.

28-Oct-2020

This application note explains the measurements on 3GPP Base Station Transmitter signals according to TS 25.141, using the Signal Analyzer FSIQ with the Code Domain Power application firmware FSIQ-K72.

17-Aug-2001 | AN-No. 1EF44

5G New Radio (NR) FR1 MIMO or beamforming downlink signal analysis especially the phase measurement of each MIMO layer and the determination of the phase difference between the MIMO layers are essential for the 5G base station product design.In this application note, it describes two test solutions from R&S® to cope with the 5G FR1 downlink MIMO signal analysis challenges either using R&S®RTP/RTO oscilloscope or R&S®NRQ6 frequency selective power sensor as RF frontend to capture the signal and together with R&S®VSE as post-processing tool for the IQ analysis.The aim of this application note is to walk the user through the necessary steps on both test solutions to enable the 5G FR1 downlink MIMO signal analysis.It is assumed that the reader has certain pre-knowledge of 5G NR physical layer. In case a refreshment is needed, please refer to the for further reading.

26-Jun-2020 | AN-No. GFM343

Rohde & Schwarz has a tool that can configure all instruments and channels from one interface to maintain an overview of the states and measurement values for all channels.

28-Apr-2023

The scope of this application note is to give a comprehensive guide on how the R&S®FSW signal and spectrum analyzer with the option R&S®FSW-K18 may be used to create a Hammerstein model for the R&S®SMW200A vector signal generator’s output stage. This model can then be applied to counteract inherent non-linearities and memory effects and improve the Error Vector Magnitude (EVM) at high output powers of the R&S®SMW200A vector signal generator.

28-Aug-2023 | AN-No. 1GP139

When measuring audio components with unknown transients, the experienced engineer watches the settling of the DUT before accepting a measured result to be valid. The settling function in the UPL/UPD simulates this process and automates it by continuously comparing the measured value with a number of measured values stored before. A measured value is only accepted as being valid if it is within the tolerance limits entered by the user. This application note explains the settling process and gives hints for practical use.

03-Jun-1998 | AN-No. 1GA12

Phase stability over time is a key characteristic for phase-coherent signals. A common 1 GHz reference signal maintains high phase stability between the RF outputs of multiple R&S®SGT100A SGMA vector RF sources.

09-Jan-2017

This application note describes Methods of Implementation (MOI) for precise, fast, and error-free compliance testing of USB 3.2 Legacy Cable Testing for USB Type A, Type B, and Micro family connector types. Based on 5 Gbps and 10 Gbps signaling per lane with vector network analyzers from Rohde & Schwarz.

09-Nov-2023 | AN-No. 1SL408

Noise sources used for noise figure and gain measurements are typically controlled by the spectrum analyzer or noise figure meter instruments and are calibrated with their ENR value (Excess noise ratio). While this external control and the use of ENR values is common in noise figure test, it may be difficult in system applications where the noise source control is not available, and the use of ENR values is replaced with the values for the noise output power of the noise source. The calculation of the output power for the noise source requires to know the P_hot value (hot power) which is not a common specification for noise sources used in test and measurement applications.This application note describes a technique to perform a calibrated noise power measurement (P_hot) with spectrum analyzers and noise sources. The next sections will give further details.

31-May-2022 | AN-No. 1EF113

Oscilloscopes are increasingly used to analyze pulsed signals such as radar signals for aerospace and defence as well as automotive applications. The oscilloscopes’ wide analysis bandwidth and manifold trigger capabilities, make them a good fit for the increasing demand for higher bandwidths and accurate signal detection in these applications. R&S®VSE vector signal explorer software is a powerful tool for comprehensive analysis of a variety of signals, providing full support to the Rohde & Schwarz oscilloscope advanced trigger system. Adjusting the trigger settings enables pulses and pulse sequences to be isolated and run full pulse analysis using the R&S®VSE vector signal explorer software.

03-Feb-2021

The R&S®FSW signal and spectrum analyzer offers fast and easy-to-use transmitter testing for the demanding DOCSIS 3.1 cable modem (CM) and cable modem termination system (CMTS) requirements.

12-Apr-2016

This white paper summarizes the technology options for supporting voice and short message service (SMS) in LTE, including circuit switched fallback (CSFB), SMS over SGs, and voice over LTE (VoLTE).

11-May-2011 | AN-No. 1MA197

The verification of emissions according to EN or FCC standards is mandatory to avoid any interference with existing users. Besides the common emission tests with measurement bandwidth up to 1 MHz and mean power measurements, most regulations also require to test peak transmission power within a 50 MHz bandwidth to avoid interference with any existing wideband applications, for example radar receivers. This application note provides information how to perform spectral emission measurements on UWB signals with spectrum analyzers using wide bandwidth RBW filters, and explains the capabilities and the limiting factors of the Rohde & Schwarz FSW signal and spectrum analyzer to perform this measurement. The next sections will give further details.

28-Jun-2021 | AN-No. 1EF109