156 Results
Query the data of all traces at once
Is there a way to query the data of all traces at once?
TRL calibration - middle of line or end of line
TRL calibration - middle of line or end of line
Loading an S-parameter file from a PC into a memory trace
Loading an S-parameter file from a PC into a memory trace
4 Port Calibration with a 2 Port automatic calibration kit possible?
4 Port Calibration with a 2 Port automatic calibration kit possible?
Which settings should I use for the Transform Time Domain mode?
Which settings should I use for the Transform Time Domain mode?
Reading the magnitude (dB) and phase (degrees) values directly
Reading the magnitude (dB) and phase (degrees) values directly
Calculate the mixed-mode S-parameter from an S4P file
Calculate the mixed-mode S-parameter from an S4P file
Cannot use internal display and external monitor together at the same time.
Cannot use internal display and external monitor together at the same time.
Changing the update display rate of a sweep with many sweep points.
Changing the update display rate of a sweep with many sweep points.
How can I change the display resolution when I use an external monitor?
How can I change the display resolution when I use an external monitor?
VNA - do I really need a sliding match for calibration?
VNA - do I really need a sliding match for calibration?
Most accurate way to measure the length of a cable with a VNA
Most accurate way to measure the length of a cable with a VNA
Calibrating a vector network analyzer (VNA) with different connectors on each port
Calibrating a vector network analyzer (VNA) with different connectors on each port
What is the function of "Resolve pool link" in the calibration manager?
What is the function of "Resolve pool link" in the calibration manager?
Converting the real and imaginary numbers to magnitude in dB and phase in degrees.
Converting the real and imaginary numbers to magnitude in dB and phase in degrees.
R&S®ZVAX-TRM User Manual
R&S®ZVAX-TRM User Manual
R&S®ZVAX-TRM Instrument Security
R&S®ZVAX-TRM Instrument Security Manual
Sending a Remote Control Ccommand Internally
Sending a remote Control Command internally
What is the correct pin layout of the DC inputs on the network analyzer's rear panel?
What is the correct pin layout of the DC inputs on the network analyzer's rear panel?
Averaged single sweep
I have set my VNA to single sweep mode and switched on averaging with a factor of 10. But when I restart the single sweep, it stops after 1 sweep and the averaging is not done.
R&S®ZCxxx Converters Getting Started
Rohde & Schwarz Getting Started for the R&S ZCxxx frequency converters
Making Spectrum Measurements with Rohde & Schwarz Network Analyzers
This application note describes how to configure a Rohde & Schwarz Network Analyzer to make spectral measurements directly on a device under test.
16-Mar-2012 | AN-No. 1EZ62
Signal integrity – calibrating a 4-port network analyzer (part 1 of 4)
TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines
ZNB Error Message "..calkit does not comply with readable calibration kit file formats"
I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.
Remote control via driver: single sweep with average of 10 - *OPC is not working
I trigger this single sweep with the RSZVB_Send_Trigger_and_Wait_for_OPC driver, but this driver does not wait for the complete 10 sweeps. If I don't use averaging, this program is works.
How can I Switch from Remote to Local State via Remote Control?
How can I switch from remote to local state via remote control?
Query of the x-values (frequency) of a trace
I query the values of a trace using scpi commands. But I get the y-values only. Is there a possibility to get the y-values also (frequency)?