1SL391 audio, breakthrough, ETSI EN 301 489 Audio Breakthrough Assembly and Test Setup 1SL391 audio, breakthrough, ETSI EN 301 489

11-Oct-2022 | AN-No. 1SL391

This Application Note describes how to configure and calibrate R&S ZVR network analyzers for conversion gain measurements of devices with two ports that have different impedances. Thus accurate measurements on frequency-converting devices such as low noise converters of sattellite receivers are possible.

16-May-2002 | AN-No. 1EZ50

Analyzing high speed datacom interfaces is an important task and ensures signal integrity. One major challenge of this analysis is the connection between the physical interface and the oscilloscope, as most of the datacom interfaces do not provide test connections suitable for RF. A test fixture is required as a bridge between the high speed datacom IF and the RF connector of the oscilloscope, but this will affect the signal integrity measurement. The R&S®RTP and R&S®RTO oscilloscopes with the advanced jitter option can analyze and separate jitter contributions. Additionally, the option can evaluate the impact of test fixtures and traces inherently and give the user a good understanding of the impact of their test setup.

15-Jul-2024

Power amplifiers for WCDMA/3GPP base stations should have the best possible spectral purity and smallest intermodulation distortion, in order to prevent disturbance of the neighbouring channels. To test such amplifiers, signal generators are required that can generate WCDMA signals with low noise and intermodulation over a very wide dynamic range. The R&S SMIQ03HD signal generator with its outstanding Adjacent Channel Leakage Ratio (ACLR) performance is especially designed for these applications. This application note describes how to use SMIQ03HD to get the best performance with 3GPP single and multi carrier signals.

02-Sep-2002 | AN-No. 1GP52

Vector Network Analyzers of t ZNA and ZNB family are able to measure magnitude and phase of complex S-parameters of a device under test (DUT) in the frequency domain. By means of the inverse Fourier transform the measurement results can be transformed to the time domain. Thus, the impulse or step response of the DUT is obtained, which gives an especially clear form of representation of its characteristics. For instance, faults in cables can thus be directly localized. Moreover, special time domain filters, so-called gates, are used to suppress unwanted signal components such as multireflections. The measured data "gated" in the time domain are then transformed back to the frequency domain and an Sparameter representation without the unwanted signal components is obtained as a function of frequency. As usual, other complex or scalar parameters such as impedance or attenuation can then be calculated and displayed.

30-Jul-2020 | AN-No. 1EP83

Keeping an ATSC (or ATSC Mobile DTV) single-frequency network (SFN) running smoothly not only requires that every single TV transmitter functions properly – the RF performance criteria echo pattern and frequency deviation also have to be strictly complied with. The R&S®ETL TV analyzer enables operators to check these crucial RF parameters at a glance with unmatched precision. The patented implementation achieves an echo delay resolution of one nanosecond, which is nearly a hundred times higher than in conventional approaches. This allows more precise control and adjustments of the several transmitters within the ATSC (or ATSC Mobile DTV) SFN and thus helps to ensure excellent coverage for the receivers.

21-Apr-2010 | AN-No. 7BM75

NGM200, NGL200 The R&S®NGL200 and R&S®NGM200 can simulate battery cells when testing battery management systems and replace far more expensive dedicated battery simulators. Testing battery management systems with Rohde & Schwarz power supplies NGM200, NGL200 The R&S®NGL200 and R&S®NGM200 can simulate battery cells when testing battery management systems and replace far more expensive dedicated battery

08-Jun-2020

The required bandwidth span for power amplifiers is growing, driven by the latest 5G and satellite enhancements.Ideally, amplifiers support multiple bands. This makes wideband testing more essential than ever before.

19-May-2020

Road safety is a global challenge at present and will be in the future. Automotive radar has become a keyword in this area and pushes again a step forward to increase driving comfort, crash prevention and even automated driving.Driver assistance systems which are supported by radar are already common. Most assistant systems are increasing the drivers comfort by collision warning systems, blind-spot monitoring, adaptive cruise control, lane-change assistance, rear cross-traffic alerts and back-up parking assistance.Today's 24 GHz, 77 GHz and 79 GHz radar sensors clearly need the capability to distinguish between different objects and offer high range resolution. That is possible with increased signal bandwidth.Furthermore, those radar systems need to cope with interference of many kinds like the one from other car's radar.This Application Note addresses signal measurements and analysis of automotive radars that are crucial during the development and verification stages. It also shows a setup to verify the functionality of a radar in case of radio interference.

10-Jun-2016 | AN-No. 1MA267

Spectrum scans are beneficial for many use-cases such as troubleshooting, interference detection and interference hunting, or verification tasks like scheduler verification or other engineering tasks. A time-gated spectrum scan, which is a power spectrum scan which applies a time gate on uplink/downlink slots/symbols and/or the guard period reveals even more details in uplink/downlink or guard period power spectrum. This allows to focus on the uplink / downlink or guard period power spectrum in 5G NR TDD networks. This educational note explains use cases for spectrum measurements, the complexity in 5G TDD and its technology basics, and which problems can be solved with the described solution. The software used is R&S®ROMES4 together with a R&S®TSMx6 drive and walk test scanner.

21-Sep-2023 | AN-No. 8NT08

This Application Note describes characterization of devices used in radar systems with pulsed signals. The emphasis is on measurements using vector network analyzers (VNAs), signal generators, vector signal generators and spectrum analyzers.

18-Jan-2008 | AN-No. 1MA124

Frequency allocation plans are under discussion in the US and Europe to open the lower C band for 5G applications. This portion of the spectrum provides 5G with more bandwidth than conventional lower mobile frequency bands and is contiguous while the C band is actually in use for satellite downlinks to satellite earth stations (SES).

18-Mar-2019

High Speed Downlink Packet Access (HSDPA) and High Speed Uplink Packet Access (HSUPA) optimize UMTS for packet data services in the downlink and uplink, respectively. Together, they are referred to as High Speed Packet Access (HSPA). Within 3GPP Release 7, 8, 9 and 10, further improvements to HSPA have been specified in the context of HSPA+ or HSPA evolution. This Application Note describes how HSPA+ features can be tested using Rohde & Schwarz instruments.

26-Apr-2013 | AN-No. 1MA121

When measuring the performance of 802.11 wireless LAN compatible receivers, Packet Error Rate (PER) tests are the method of choice today. This application note describes a simple way to conduct PER tests using signal generators on any 802.11 device, independent of their physical layer design (11b, 11a or 11g). The application software works with standard Windows™ drivers on any card independent of manufacturer. No additional hardware specific software is needed. Easy setup of the source signal is included with direct upload to an SMIQ or AMIQ.

09-Jan-2012 | AN-No. 1GP56

A lack of lip synchronicity is an effect that can severely impair the quality of TV reception. With modern digital signal processing, this audio-to-video delay occurs much more often than in earlier times when analog signal generation was used. The total delay can reach several hundred milliseconds, which is immediately noticeable on a TV home receiver. To prevent such impair-ments, the audio-to-video delay must be measured.

27-Aug-2002 | AN-No. 7BM44

Analyzing RF pulses is a key aspect of pulsed radar applications, e.g. in air traffic control (ATC), maritime radar or scientific measurements of the ionosphere. Analyzing the envelope and the modulation of the pulse is essential, because they contain important information to characterize the application. The R&S®RTO and R&S®RTP oscilloscopes are capable of triggering precisely on a pulse as a prerequisite for time domain and frequency domain analysis. This document describes the use of the R&S®RTO and R&S®RTP to trigger exactly on pulses in preparation for further in-depth measurements such as RF pulse measurements on an ATC signal.

13-Mar-2019

This application note introduces the reader to the SpaceX Hyperloop Pod Competition project and their special demands for the electrical drive train. Common motor technology like brushless motors and their typical control methods widely used in the industry are also discussed within this document.However, the main focus of this paper is a demonstration of a power measurement method of a three-phase inverter by means of a 4-channel oscilloscope. Not only the theory of the power measurement is presented but also the conducted measurement is presented including tips and tricks to obtain the best measurement results.The measurement solution provided by Rohde & Schwarz was mandatory for the TUM Hyperloop team to overcome challenges in optimization of the electrical drive train used in the SpaceX Hyperloop Pod Competition project.Many thanks to Mr. Johannes Ungar and Faruk Centinkaya (TUM Hyperloop) for contributing significantly to this application note. By combining their expertise in electrical drive trains used in the Hyperloop Project and with a Test & Measurement solution from Rohde & Schwarz, we have achieved synergies that will be beneficial for any design and test engineers in the industry.

31-Mar-2021 | AN-No. GFM360

New functionality for R&S®M3SR Series4400 radios

09-Feb-2015

R&S®CMWcards, an intuitive and user-friendly software application, makes it possible to recreate field testing in a lab environment

19-Feb-2019

The R&S spectrum analyzers and signal analyzers offer an additional equalizer filter in the Vector Signal Analysis Application Firmware R&S FSQ-K70/FSx-B73, which is a powerful tool for measurement and analysis of vector-modulated signals. This application note describes the functionality of the equalizer filter and how to set the filter parameter manually in an accurate and fast way.

06-Feb-2009 | AN-No. 1EF61

With the R&S®Pulse Sequencer radar simulation software, users can easily and intuitively create scenarios for simulation of angle of arrival (AoA). Together with multiple coupled R&S®SMW200A vector signal generators, this solution allows quick and thorough performance characterization of all types of direction finding equipment such as devices that use amplitude comparison, interferometric or time difference of arrival (TDOA) techniques. This document describes our test solution for testing devices that use amplitude comparison techniques.

02-Apr-2020

This application note is step by step guide on 5G New Radio (5G NR) signal generation and analysis capabilities using the R&S®SMW200A Vector Signal Generator equipped with software option SMW-K144 (5G NR option), in combination with the R&S®FSW Signal and Spectrum Analyzer and the software options FSW-K144 & FSW-K145 (5G NR Downlink & Uplink Signal Analysis). The R&S®VSE Vector signal explorer has also been used for analysis purpose in parallel to the FSW-K144 & FSW-K145 software options.It is assumed that the reader already has a deep understanding of the 5G New Radio standard as well as the testing aspects. If not, then please refer to the 5G eBook more a detailed overview on the fundamentals, procedures, testing aspects of the 5G NR technology.

22-Nov-2019 | AN-No. GFM322

When MPEG-2 transport streams are transmitted, the program clock reference PCR is transmitted as a time reference in the receiver. A sufficiently accurate and correctly received PCR is a precondition for correct data display in the receiver. This Application Note provides an overview of definitions, functions and use of the PCR. It also explains the recommended measurements of the current measurement guidelines and offers detailed instructions on how to use the PCR measurement functions of the R&S DVM family.

01-Jun-2006 | AN-No. 7BM55

The FLO in MediaFLO stands for 'forward link only'. MediaFLO technology covers transmission of files and multimedia content to handheld devices. The FLO device minimum performance specification (MPS) was created to ensure that FLO receivers can receive a FLO service that fulfils the compatibility guidelines of the FLO air interface specification. This Application Note shows how the Broadcast Test System R&S SFU from Rohde & Schwarz can be used to generate all test scenarios required by the minimum performance specification.

31-Aug-2006 | AN-No. 7BM62

The validated UWB PHY test suite for the R&S®CMP200 radio communication tester simplifies FiRa™ Consortium PHY conformance testing.

21-Jun-2022

Rohde & Schwarz signal generators present a compact easy-to-use solution for generating phase coherent signals. Different generator models can be coupled to optimally fit user requirements in terms of number of phase coherent channels and RF frequency range.This application note explains how to generate phase coherent signals, details what to consider and how to best calibrate the relative phases and timing between the individual channels. This document also presents various measurements of the phase stability over time for different RF frequencies.

07-Sep-2016 | AN-No. 1GP108

combinational tests, terminal equipment, test system, electrical test, telecommunicaitons, open test platform, CompactTSVP, DUT, acoustic characteristics, GTSL, diver, ETSI Combinational tests for telephone terminal equipment Combinational tests for telephone terminal equipment combinational tests, terminal equipment, test system, electrical test, telecommunicaitons, open test platform, CompactTSVP

26-Apr-2006

The R&S®SFU broadcast test system is used as a reference signal generator to simulate the influence of LTE and other mobile radio signals on digital TV signals and receivers.

20-Jun-2012

Verifying 5G transmitted signals in the field with the R&S®Spectrum Rider FPH handheld spectrum analyzer

30-Jul-2024

In modern telephoning, dual-tone dialling is used more and more often. Every symbol to be transmitted is coded by two frequencies which are sent at the same time. To ensure a trouble-free call setup, transmission has to be done within defined tolerances. For measuring these kind of dialling signals, the measurement equipment has to fulfill high requirements. This application note describes how the measurements can be carried out by using the Audio Analyzers UPL or UPD. It also presents a measuring program for this application.

04-Jun-1998 | AN-No. 1GA23