8307 Results
For measurement settings below 10 mV/div, oscilloscopes typically reduce the measurement bandwidth in order to keep the trace noise as low as possible. The R&S®RTO is different: It offers the full bandwidth even for the most sensitive settings, and an A/D converter with more than 7 effective bits (ENOB) digitizes the signal.
13-Jul-2012
Solutions and Tipps for NR FR1 in TDD Downlink Mode
5G New Radio (NR) is a radio technology specified by 3GPP and was first released in 3GPP release 15. It is designed to target three use cases, i.e. enhanced mobile broadband (eMBB), massive machine type communication (mMTC) and ultra-reliable low latency communication (URLLC). Among these three use cases, eMBB represents actually a further evolution of mobile broadband communication from LTE standard. According to the technical performance requirement defined by IMT-2020, by deploying 5G technology, peak data rates of eMBB application are expected to reach 20 Gbps in downlink (DL) and 10 Gbps in uplink (UL) direction, respectively. Typical use cases of eMBB are data hungry applications, such as high resolution 8K video streaming, virtual reality (VR), augmented reality (AR) etc.Verification of a 5G capable user equipment (UE) with respect to its achievable maximum data throughput under controllable and deterministic test conditions is an essential process during the design phase of the product. Performance centric verification through identification of the data throughput bottleneck, product benchmarking against a golden device enhances tremendously the user experience in the end.This document focuses on 5G NR frequency range 1 (FR1) with TDD duplex mode in E-UTRAN New-radio Dual Connectivity (ENDC) operating mode. As 5G NR physical layer offers a plethora of flexibility, the motivation here is to provide a kind of guideline of relevant parameter settings to stimulate device under test (DUT)'s max throughput capacity. The status quo of the R&S solutions at the time when the application note is created are described. Shown feature sets are constantly evolving, so the screenshots used and the parameters shown may change.
07-Jul-2022 | AN-No. 1SL379
Measurements on PCS1900 Mobile Stations According to J-STD-007
01-Nov-1996 | AN-No. 1EF22
Remote Emulation with the R&S<sup>®</sup>SMA100A Signal Generator
17-Aug-2015 | AN-No. 1GP93
In this application note the fundamental working principles of active antennas and the differences compared to passive antennas are asserted.
03-Feb-2016 | AN-No. 8GE02
Crime scene investigation with cellular network analysis
14-Mar-2024
The R&S®RTx-K50 option expands the addressable range of interface standards by adding decoding capability for standardized and proprietary Manchester or NRZ coded buses.
19-Oct-2020
Trace minimum hold function and utilize better visualization of persistent interferers with the R&S®MNT100, R&S®PR200, R&S®PR100 and R&S®DDF007.
15-Jul-2019
In this App card you will learn more about Interference hunting in TDD networks with the polychrome display method and solutions from Rohde & Schwarz.
09-Sep-2020
Current radar development is focusing on the area of signal processing. This is taken into account by this educational note, where the R&S®SMW / SMBV instruments on the transmitter side and R&S®FSW / FSV instruments on the receiver side are combined to a closed loop Radar system.
20-Nov-2014 | AN-No. 1MA234
The Yamaha® MP Series combined with the R&S®ZNBT vector network analyzer measure the high frequency characteristics of a production lot at high speed and high accuracy.
27-Jan-2020
Power Measurements on WLAN Modules with the R&S CMU 200 and with CMUgo
18-Oct-2005 | AN-No. 1CM55
Application Note Peak and Mean Power measurements on wideband FMCW radar signals
28-Jun-2019 | AN-No. 1EF107
The R&S®ZNL is an economic solution that can characterize a variety of DUTs both via network analysis and spectrum analysis without requiring a lengthy setup.
17-Dec-2021
An automated test solution based on the R&S®CMW wideband radio communication tester fully supports the new test cases for real-time submeter positioning.
10-Jun-2022
Simulation of BCCH Channel of GSM/PCN Base Station with Signal Generator SME
01-Jul-1999 | AN-No. 1GPAN14
This application note provides practical hints to accurately characterize and de-embed these lead-in and lead-out structures with R&S Vector Network Analyzers ZNA, ZNB, ZNBT and ZND.
19-Sep-2022 | AN-No. 1SL367
This application card will give some guidance as to the possible combinations of bandwidth options and mixers in conjunction with the needed IF frequencies.
16-Jun-2020
Selecting Your Next Oscilloscope:
If you are selecting your next oscilloscope and want more insight on how to understand ENOB values measured and published by oscilloscope manufacturers, this document is for you. The effective number of bits (ENOB) is a way of quantifying the quality of analog to digital conversion. A higher ENOB means that voltage levels recorded in analog to digital conversion are more accurate. Understanding oscilloscope vendor-supplied ENOB values can be complex. This document focuses on interpretation of measured ENOB results made on oscilloscopes rather than the math behind ENOB calculations.
21-Jun-2024 | AN-No. 1TD12
Tolerance to Noise Tests for DTV Receivers
26-Jan-2007 | AN-No. 7BM64
This paper describes the measurement of additive/residual phase noise of power amplifiers or multipliers for example for automotive RADAR sensors at 80 GHz using the interferometric measurement approach in combination with a phase noise and VCO tester R&S FSWP. The setup provides a way to characterize the additive/residual phase noise of amplifiers down to -150 dBc/Hz at 100 kHz offset even in the microwave range at 80 GHz.
11-Sep-2024 | AN-No. 1EF117
The R&S ® TSStream multi-TS streaming software streams a number of MPEG transport stream files simultaneously over a single IP interface.
16-Mar-2017 | AN-No. 1GP113
R&S CMWrun Sequencer Software Tool
20-Feb-2015
Rohde & Schwarz offers RF solid-state amplifiers for various frequencies ranging from 9 kHz to 6 GHz and delivering CW power up to 80 kW.
27-Apr-2016
This application note describes the basic frequency filter measurements that are often required during service repairs, during development and for training purposes.
27-Mar-2015 | AN-No. 1MA243
Measurements on AMPS phones with the R&S CMU200 and CMUgo
07-Sep-2004 | AN-No. 1CM53
This document is divided in two parts and starts with an introduction in AC-DC conversion principles in general. It will present the most common circuits used for different power levels. The switching mode power supply (SMPS) converter will be the main focus as they are used everywhere in the electronics. Especially the flyback converter design in different flavors are highlighted. Nevertheless, all measurements are also applicable for other SMPS converter designs operating at higher power levels.In the second part of this document, most relevant testing methods and procedures of an AC-DC converter are highlighted. For each testing section, a fundamental part will be upfront discussed and it is followed by a presentation of a suitable measurement method. In this second part, the device under test (DUT) is considered as black box device and thus the structure is similar. Therefore, the testing parts consists of methods related to input tests, output tests and a combination of both like efficiency. Of course, some test performed at the output of the converter are also relevant for DC-DC converter, e.g. the validation of the output ripple.
14-Nov-2022 | AN-No. 1SL387
CDMA2000® Base Station Test with R&S Equipment
05-Sep-2003 | AN-No. 1MA61
This application note describes a test scenario tor cable components with an R&S®CLGD Cable Load Generator and an R&S®FSW Signal & Spectrum Analyzer.
24-Jan-2017 | AN-No. 1MA285