Adjacent Channel Power performance of power amplifiers used in digital TV systems has to be guaranteed over a wide frequency range, 54 to 890 MHz, which may lead to time consuming test procedures. The application software described here provides swept ACP analysis, using AMIQ and SMIQ for signal generation and FSP, FSU or FSE for signal analysis. ACP measurement is performed according to FCC Regulation 47CFR 73.622(h).

16-Oct-2001 | AN-No. 1MA43

radio signals, automatic monitoring, interference, RF radiation, frequency spectrum, Automatic monitoring of radio signals interfering with sensitive devices in hospitals Automatic monitoring of radio signals interfering with sensitive devices in hospitals radio signals, automatic monitoring, interference, RF radiation, frequency spectrum, Automatic monitoring of radio signals interfering with sensitive

04-Sep-2006

Measurements of very high noise figure components are performed for a number of reasons. For instance, in a wide range of applications, devices under test (DUT) are characterized within a complex test setup that includes high losses before or after the low noise DUT. In case of high frequencies, the switch matrix with complex signal routing and cables might have a very high loss. In other cases, the device might be embedded in a test setup where direct access is physically impossible, on-wafer probing is one example for this case. Using conventional measurement equipment, the noise figure measurement of such a device is very unstable if not impossible at all.

24-Jun-2020 | AN-No. 1EF110

This application note describes how Bluetooth devices are tested and measured using the R&S CMU200/CBT by means of the CMUgo/CBTgo remote control program or manual operation.

06-Oct-2006 | AN-No. 1CM50

During development of MU-MIMO antenna arrays, the beamforming algorithms undergo steady revision. Whether used in regression testing or verification of newly introduced features, fast beamforming verification helps to speed up R&D for beamforming antennas and improve performance of your product.

07-Jul-2020

This application note describes how to generate the noise field for ambient noise rejection tests according to 3GPP TS 26.132, sections 7.9 and 8.9.

12-Oct-2010 | AN-No. 1GA51

The introduction of the transmission of compressed TV signals to MPEG2 and DVB for cable, satellite and terrestrial (COFDM) lead to the creation of many abbreviations that have to be explained to the “uninitiated”. In the previous three lines, three abbreviations whose meanings are not obvious have already been mentioned. A table explaining what these abbreviations mean is therefore essential.

20-Jul-2001 | AN-No. 7BM27

Next Generation Emergency Call (NG eCall) is a extension of eCall, a service provided in Europe with the goal of reducing response times for accidents or other emergencies on the roadways. This application note briefly describes the technology behind NG eCall and presents conformance tests for NG eCall using the R&S®CMW500 RF tester and either the R&S®SMBV100B or the R&S®SMW200A vector signal generator. The test software for NG eCall (R&S®CMW-KA096) makes it quick and easy to perform these tests with the LTE wireless communications standard.

06-Jun-2019 | AN-No. GFM312

The R&S MATLAB® Toolkit for R&S® NRP-Z Sensors provides routines for remote controlling these instruments via USB or the R&S® NRP Power Meter. This application note describes how to access the sensors using the R&S® VXI PnP driver. It also contains a set of scripts that perform commonly needed tasks, such as opening a sensor connection or performing measurements.

05-Mar-2011 | AN-No. 1GP61

The R&S®RTO6 oscilloscope has an in-depth tool for debugging custom and commercial off-the-shelf serial buses for the avionics and aerospace industries.

20-Dec-2023

This application note describes how to use two or more Arbitrary-/Function Generators R&S® AM300 to generate multi-phase-sychronized signals, which are required in some applications.

27-Jun-2007 | AN-No. RAC-0705-0038

Since June 2017 almost all radio transmitters and receivers sold or put into operation in the European Union have to be tested for immunity against interferers in adjacent frequency bands. ETSI standard EN 303 345 defines the tests to be performed on broadcast sound receivers, and the requirements to be passed.This application note describes the test procedures and provides script files and interferer signals for the Broadcast Test Center R&S®BTC.

29-May-2020 | AN-No. 1GP117

Using a Vector Network Analyzer from the ZVR family, not only magnitude and phase can be measured, but also group delay and even phase delay. Whereas phase delay measurements produce the highest accuracy for the electrical length of non-dispersive devices under test, such as coaxial cables, group delay measurements also give a detailed insight into the frequency dependent delay characteristics of dispersive devices, such as filters. In addition to the traditional step aperture technique, Vector Network Analyzers from the ZVR family offer a frequency aperture technique, which allows a well defined and constant aperture for group delay measurements also for a nonlinear frequency sweep.

28-Jul-1998 | AN-No. 1EZ35

For establishing a WLAN connection between R&S®CMW and device under test (DUT), the WLAN properties at the R&S®CMW have to be adapted to the test conditions. These can vary in several aspects, particularly due to the different WLAN standards and characteristics of the DUT. This document describes the critical parameters and provides step-by-step procedures for the configuration.

08-Dec-2015 | AN-No. 1C106

How I/Q noise cancellation can help significantly improve the EVM performance of your signal and spectrum analyzer.

16-Nov-2023

The R&S®SMB100A RF and microwave signal generator offers a remote emulation feature that makes it possible to control the instrument by commands other than the built-in native SCPI commands. This feature allows the user to replace signal generators, e.g. from other manufacturers, with the R&S®SMB100A without having to change the remote control code. This application note describes how to use the remote emulation feature in general. Furthermore, it describes in detail the remote emulation for each supported instrument, limitations of the individual emulations and the remaining differences between the emulated and the original commands.

20-Mar-2012 | AN-No. 1GP89

Near Field Communication (NFC) is a new short-range, standards-based wireless connectivity technology, that uses magnetic field induction to enable communication between electronic devices in close proximity. Based on RFID technology, NFC provides a medium for the identification protocols that validate secure data transfer. NFC enables users to perform intuitive, safe, contactless transactions, access digital content and connect elec­tronic devices simply by touching or bringing devices into close proximity. This White Paper gives an overview of NFC uses, NFC technology and signals and RF measurements on NFC units. NFC analog measurements with R&S test instruments are described in detail in R&S application Note 1MA190 'Basic Tests of NFC Enabled Devices Using R&S Test Equipment'

03-Jun-2013 | AN-No. 1MA182

Sequencer Software Tool

20-Feb-2015

Sporadic events and errors may occur when developing new measurement instruments and need to be taken into account in all design stages and analyses. The Rohde & Schwarz power supplies can precisely capture such sporadic events and errors.

02-May-2023

The R&S®QPS quick personnel security scanner transforms people-screening technology with its high-performance, fully electronic and solidstate flat panel design that has no moving parts. The R&S®QPS improves the security screening experience and operations by having a simple open design for a spacious screening environment and unobstructed view for security personnel, making high-resolution people screening more comfortable and efficient than ever before.

15-Apr-2019

Modern, capacitive touchscreens as used, for example, in mobile phones are susceptible to common mode noise exhibited by external power supplies (EPS).

17-May-2018

An easy-to-setup test solution for high speed multichannel acquisition for 5G NR signals

04-Mar-2020

R&S®RTP, R&S®RTO, R&S®RTE, oscilloscopes, acquired waveform data, python How to work with acquired waveform data in Python using the R&S®RTP, R&S®RTO or R&S®RTE. Working with acquired waveform data in Python R&S®RTP, R&S®RTO, R&S®RTE, oscilloscopes, acquired waveform data, python How to work with acquired waveform data in Python using the R&S®RTP, R&S®RTO or R&S®RTE. Working with acquired waveform

12-Jan-2022

In this day and age of internet of things, more and more devices are connected to the local network, making it even more difficult for the IT department to monitor them. Rohde & Schwarz instruments are also increasingly accessed via their LAN interface, which provides additional convenience features such as remote desktop, SMB file transfer or a web interface. To make it easier to monitor the use and status of instruments, some devices offer a software option, the Health and Utilization Monitoring Service (HUMS).HUMS can be accessed via SNMP and REST (HTTP) and provides all necessary information about the health status and utilization over time in many details.This application note describes how to access HUMS and what data is provided.

11-Jan-2021 | AN-No. GFM336

The R&S®ELEKTRA EMC test software is a solution that controls complete EMC systems and automates measurements on equipment under test that is being tested for emissions and immunity compliance. It can be used to remotely control R&S®AdVISE, which is a visual inspection software to monitor up to 32 different Regions of Interest in one video for visible and audible changeThis Application Note describes how to set up R&S®ELEKTRA and R&S®AdVISE for remote testing.

23-Jul-2020 | AN-No. 1S005

This application note describes how to measure the control loop stability of switch-mode power supplies to get the best performance and confidence of the design. It will explain the main measurement concept and will guide the user during the measurements and mention the main topics in a practical manner. Wherever possible, a hint is given where the user should pay attention to it to avoid weak measurements. The Rohde and Schwarz buck converter reference board was designed in collaboration with Texas Instruments and is used to illustrate the closed loop measurement in a practical manner.

01-Jul-2019 | AN-No. GFM321

All types of information transmission, including the 'one-way' transmission used in broadcasting, involve feeding a radio frequency (RF) signal to an antenna. This is the essence of the most basic type of transmitter used to emit electromagnetic waves. In the real world, however, a transmitter used for broadcast applications, for example, is much more complex in terms of its functions and design. The different transmitter components must be carefully coordinated. There are many quality parameters that are critical in ensuring that a proper output signal is delivered. Rohde & Schwarz designed the R&S® ETL TV analyzer especially for broadcasting applications. The analyzer allows the measurement of the quality parameters that are relevant in analog and digital broadcasting. This Application Note describes the typical quality measurements performed during compliance testing of TV transmitters. The approach discussed here is based on the example of Rohde & Schwarz terrestrial transmitters for analog TV and DVB-T/H.

19-Sep-2007 | AN-No. 7BM67

In high-speed digital measurement applications, test fixtures are commonly used to connect devices under test to measurement equipment. Characterization, and analysis in the time and frequency domains that accounts for various constraints helps to remove the influence of these fixtures.

23-May-2023 | AN-No. 1SL393

Signaling checks, DSMCC object carousel analysis and fault localization all in one instrument: R&S®DVMS, R&S®DVM or R&S®ETL

28-Dec-2012

Embedded power supplies combine traditional power supply components with multiple sensors, processing and control logic as well as digital communications interfaces. Test equipment for debugging requires isolated input channels for measurements of hazardous voltages. Additional digital channels support the analysis of digital signals, while trigger and decode capabilities are essential for time-correlated monitoring of serial protocol-based communications interfaces.

26-Apr-2016