With AMPTUNE amplifier nonlinearity can be measured with signals that are typical for the signals encountered by the amplifier in day-to-day use. The measurement can be checked by pre-distorting the control signal. Also, the results can be automatically stored for further processing with external programs.

26-Oct-2005 | AN-No. 1MA27

Rohde & Schwarz recognizes the potential risk of computer virus infection when con-necting Windows®-based test instrumenta-tion to other computers via local area net-works (LANs), or using removable storage devices.This white paper introduces measures to minimize malware threats and discusses ways to mitigate risks while insuring that instrument performance is not compro-mised.The paper discusses the use of anti-virus software. It also outlines how to keep the Windows® 7 operating system properly updated through regular installation of OS patches.

27-Jan-2015 | AN-No. 1DC01

TS-EMF3 TS-EMF TRD Konvertierung (german) TRD Konvertierung (German) TS-EMF3 TS-EMF TRD Konvertierung (german)

11-Nov-2005 | AN-No. TS-EMF3

The R&S®ESW-B8 and R&S®ESW-B8E extended bandwidth options allow the R&S®ESW EMI test receiver to measure with a resolution bandwidth of up to 80 MHz. The increasing number of wideband applications (e.g. radar sensors) and accompanying standards means there is now a greater interest in wide bandwidth measurements.This application note describes the following topics for the R&S®ESW EMI test receiver:► Characteristics and implementation of RF signal paths► Image responses and how their rejection is handled ► Ultrawideband measurement applications as required e.g. by ETSI standards► Solutions for efficiently coping with bandwidth limitations in the range above 8 GHz

19-Nov-2020 | AN-No. 1EE26

Measurement deviations due to systematic errors of a network analysis system can be drastically reduced by an appropriate system error calibration. After system error correction, the residual measurement uncertainties are - besides the stability, linearity, and dynamic range of the network analyzer system - mainly affected by the quality of the calibration standards and the repeatability of the connections. The effective measurement accuracy of the network analysis system can be determined using the results of successive verification measurements utilizing highly precise verification standards.

24-Jan-2001 | AN-No. 1EZ48

High Speed Uplink Packet Access (HSUPA) is a 3GPP release 6 feature for WCDMA. Objective is to achieve uplink data rates of up to 5.76 Mbps and increase throughput and capacity. This application note introduces HSUPA concepts and explains key features.

09-Feb-2006 | AN-No. 1MA94

This Application Note gives a short overview how signals with two different modulation schemes can be analyzed using the R&S®FSW (or R&S®FPS) using its Multi-Standard-Radio-Analyzer (MSRA) and Vector Signal Analysis personality. The Application Note focuses on DVB-S2(X) signals, but the approach may be used for similar signals as well, as e.g. used in microwave backhaul links.The Application Note also provides a software tool that automates the configuration and provides the variety of different constellations that are used within DVB-S2(X).

18-Apr-2016 | AN-No. 1EF93

Spectrum and network analyzers equipped with network interface cards can be integrated in Local Area Networks (LAN). This Application Note describes how to remote control these instruments over a LAN and use VXIpnp instrument drivers over a LAN.

25-Jun-2003 | AN-No. 1EF47

High sampling rate and automatic pulse analysis make the R&S®NRP-Z8x wideband power sensors ideal for time-domain analysis of radar pulses.

06-Aug-2013

This application note addresses the diverse possibilities of interoperability between Rohde & Schwarz power sensors and Rohde & Schwarz signal generators. All current and many legacy Rohde & Schwarz signal generators offer the capability of directly connecting power sensors. This enables power measurements without the need of a base unit or separate PC to display the readings. Furthermore, sensors can be used for special tasks like filling a user correction table or continuously controlling levels at crucial points in the measurement configuration.

31-Aug-2023 | AN-No. 1GP141

broadcasting transmitters, allocated frequencies, monitoring control center, RF power, Automatic monitoring of emission parameters of registered broadcasting transmitters Automatic monitoring of emission parameters of registered broadcasting transmitters broadcasting transmitters, allocated frequencies, monitoring control center, RF power, Automatic monitoring of emission parameters of registered broadcasting

04-Sep-2006

DIRECTV®, a digital TV broadcast system, makes use of transport packets with a length of 130 bytes rather than the more common 188 bytes used in MPEG TS streams. The inputs on the R&S® SFU do not accept transport streams in the DIRECTV® format. This Application Note introduces R&S® DIRECTV tool and explains how it can be used to convert existing 130-byte-based DIRECTV® transport stream content to 188-byte-based ISO 13818-1 streams that are compatible with the R&S® SFU SPI input or the internal R&S® SFU TRP player. This tool is intended for Rohde & Schwarz customers who are licensed to operate an R&S® SFU-K9 DIRECTV coder or R&S® SFU-K108 AMC coder.

05-Oct-2007 | AN-No. 7BM69

The R&S®FSMR3000 (hereinafter FSMR) is a three-in-one instrument incorporating a Measurement Receiver, a Signal and Spectrum Analyser, and a Phase Noise Analyser.This application note demonstrates the use of the FSMR, including the Cross-correlation option (R&S®FSMR3-B60), to measure the Phase Noise characteristics of a raw Signal Generator (R&®SMA100B).The Cross-correlation phase noise measurement improves sensitivity by 5 · log(n) dB, compared with measurements that do not use this option. For example, a measurement using 10 correlations, improves the phase noise floor by 5 dB.

31-Dec-2021 | AN-No. 1SL376

Voice over IP for air traffic control

02-Nov-2011

Rare faults and intermittent signals are difficult to capture. The R&S®RTO Oscilloscope supports the acquisition and the detailed signal analysis of these signals by using the history mode. The history mode allows the user to look back to previous acquisitions and apply the wide set of analysis functions of the RTO. Furthermore it stores the accurate recoding time of the waveforms for subsequent analysis.

03-Jun-2013 | AN-No. 1TD02

This application note describes how to set up 3GPP FDD and LTE multicell and multi-UE scenarios with the R&S®SMU200A with a focus on routing and leveling of the baseband signals. Furthermore, it describes in detail how to determine the correct AWGN settings, i.e. how to calculate the required signal-to-noise ratio for the various scenarios.

10-Aug-2011 | AN-No. 1GP80

This application note provides a guide through the measurements for IEEE 802.11ac WLAN transmitter signals using the general purpose OFDM analysis software R&S FS-K96. Step-by-step instructions for performing the measurements are provided and the different result types available with the FSK96 Software are discussed.

22-Sep-2011 | AN-No. 1EF82

RTC, RTC1000, Application Card, Determining current-voltage characteristics with the oscilloscope With their included component tester, the R&S®RTC1000 oscilloscopes are universally deployable in development and educational environments. Determining current-voltage characteristics with the oscilloscope RTC, RTC1000, Application Card, Determining current-voltage characteristics with the oscilloscope

20-Dec-2017

RF performance measurements for Wi-Fi 7.

30-May-2022

The new buffer analysis feature was introduced with firmware version 2.80 for the R&S DVM family. This application note describes this feature and explains how it represents a valuable asset to your daily business operations This application note first provides background information and then explains how monitoring and measurement have been implemented in the R&S DVM family.

23-Mar-2006 | AN-No. 7BM53

CST® Filter Designer 3D, which is part of the CST Studio Suite® simulation software from Dassault Systèmes, is a complete synthesis tool for filters and diplexers. It provides a range of solutions throughout the design process of coupled resonator filters and even beyond with its VNA based tuning capability. CST Filter Designer 3D assists in tuning filter hardware, significantly reducing the time for optimizing a device to meet the expected specifications. An attractive instrument to obtain fast data reading for realtime filter tuning is the R&S®ZNB vector network analyzer from Rohde & Schwarz.

27-Nov-2019

With the R&S®RTB2000/RTM3000/RTA4000 oscilloscopes, you control and interact remotely via LAN. These oscilloscopes incorporate the USB-based connectivity standard media transfer protocol (MTP).

20-Mar-2017

For A/V devices such as smartphones, tablet PCs, Blu-ray players, set-top boxes and TV sets, the perceived video quality must satisfy very high standards. A/V devices need to hold their own in three main areas:ı Stability (environmental influences, response to source signal disturbances, etc.)ı Performance (switching times, delays)ı Compliance with standards (input and output formats)Any deviations from the expected video and audio output can be automatically and precisely detected with R&S A/V distortion analysis on all common analog and digital interfaces such as HDMI™ and MHL™.This document examines the relevant setups and configurations.

15-Oct-2014 | AN-No. 7BM87

Create and simulate detailed traffic situations for the verification of cellular V2X (C-V2X) connectivity

30-Jun-2022

The R&S®SMW200A GNSS simulator offers an easy and convenient way to test your receiver design against a wide variety of potential interferers and jammers. Test cases extend from simple coexistence simulations to complex interference scenarios with localized emitters.

28-Jan-2019

Simultaneous DL throughput verification and UL transmission testing with the R&S®CMW500

29-Jul-2009

With the extension of the 3GPP FDD system to include HSDPA, the HS-DPCCH has been added as a new code channel in the uplink. This Application Note describes the transmitter measurements provided by the CMU200 to perform the transmitter measurements defined in TS 34.121 in presence of the HS-DPCCH. CMU200 receiver measurements according to TS 34.121 that measure the throughput and the CQI reporting are described. Subject to change – T. Braun, November 2005 - 1CM62

25-Nov-2005 | AN-No. 1CM62

Modulation Analyzers FMA (up to 1.36 GHz) and FMB (up to 5 GHz) are high-grade FM demodulators from Rohde & Schwarz with highly stable synthesizer, low-noise FM demodulator, automatic frequency tuning and fine-tuning, separation of AM from FM,all of which make Analyzers FMA/FMB ideal for phase noise measurements.

03-Jun-1998 | AN-No. 1EF15

The I/Q-Modulation Generator AMIQ provides high precision I/Q analog output for data calculated by the software WinIQSIM. Additionally, the software AMIQ-K2 enables you to read, convert, and transfer existing data files from various other programs to AMIQ format. Input formats supported by AMIQ-K2 are: - The propriety R&S programs IQSIM and DAB-K1. - Mathematic calculation programs like Matlab and Mathcad. - AWG202, COSSAP and ADS data files. AMIQ-K2 also provides you with remote control for AMIQ. For hardware and software requirements see section 2. AMIQ-K2 transfers data to AMIQ using either - GPIB - RS232. An extensive manual is supplied to help you use AMIQ-K2.

24-Nov-1999 | AN-No. 1MA10

This application note describes the general setup and required equipment for EMC measurements according to the EMS standard IEC / EN 61000-4-6.

29-Mar-2007 | AN-No. 1SP31