Download Center

Easy configuration of frequency domain analysis Easy configuration of frequency domain analysis Video, RTO2000, Oscilloscope, Responsive FFT and spectogram Easy configuration of frequency domain analysis

R&S RT-ZPR20 Accurate and fast power integrity measurements - Application Card

Russian version - времени простоя цифрового осциллографа на измерения

Russian version - Анализ джиттера с помощью цифрового осциллографа R&S®RTO

Shown on a USB 3.1 Gen1 device Video, RTO2000, Oscilloscope, Signal integrity debugging Shown on a USB 3.1 Gen1 device

How to perform signal integrity debugging on a DDR3 device Video, RTO2000, Oscilloscope, DDR3 DDR3 signal integrity debugging

How to analyze basic paramters of pulsed RF signals Video, RTO2000, Oscilloscope, How to analyze basic paramters of pulsed RF signals

Power rail probe in combination with high performance oscilloscope Video, RTO2000, Oscilloscope, Power integrity debugging Power rail probe in combination with high performance oscilloscope.

Power sequencing test solution

How to measure pulse sequences in time and frequency domain Video, RTO2000, Oscilloscope, RF pulse train analysis How to measure pulse sequences in time and frequency domain

Up and down Chirp analysis in time and frequency domain Video, RTO2000, Oscilloscope, Analysis of complex radar signals Up and down Chirp analysis in time and frequency domain

This application note along with its corresponding white paper 1MA207 show how to use the R&S radar product portfolio to tackle test and measurement tasks in modern radar technology.

10-Aug-2012 | AN-No. 1MA127

How to use realtime deembedding on a USB 3.1 Gen1 device video, oscilloscope, RTO2000, USB 3.1 How to use realtime deembedding on a USB 3.1 Gen1 device.

This application note summarizes the Rohde &Schwarz test solutions for LTE-Advanced (Release 10) using Vector Signal Generators, Signal and Spectrum Analyzers and the Wideband Radio Communication Tester.

03-Sep-2014 | AN-No. 1MA166

Video, oscilloscope, RTO2000, Time delay analysis of multiple wideband RF signals Analysis of multiple RF signals, which are typically used e.g. for direction finding.

Oscilloscope bus decoding, RTO2000, bus decoding, I2C Dive into your protocol to check for any problems with your I²C interface.

The demand having a snubber circuit in the power supply topology leads to specific verification methods during the design which are the main focus within this document.

23-Jun-2021 | AN-No. 1SL363

This document provides an introduction to SDR as used for military radios and presents the relevant T&M solutions offered by Rohde & Schwarz.

15-Sep-2012 | AN-No. 1MA206

Discover some of the key parameters of an oscilloscope and how they impact on the performance in this video series: Part 1: Bandwidth and frequency response R&S®RTO2000 Video, application videos, oscilloscope, troubleshooting, mixed signal oscilloscope R&S Talking about bandwidth Open Lightbox Talking about bandwidth

The R&S®RTO-K92 eMMC Compliance Test option offers an automated test solution for the electrical interface of an eMMC device according to the JEDEC specification, revision 5.1. Oscilloscope Application Videos, Application Video, Application Videos, Videos, eMMC Interface Compliance Test Learn how you can use the eMMC compliance test of R&S for automated testings of electrical interfaces!

RTO2000, debugging, EMI When debugging EMI problems in electronic circuits, development engineers face the challenging problem of quickly and accurately identifying and eliminating the sources of unwanted emissions. Many problems can be eliminated during development by using oscilloscopes for EMI debugging.

Importance of deep memory in digital oscilloscopes - Rohde & Schwarz oscilloscopes offer industry-leading memory depth.

21-Mar-2017

Secondary surveillance radar (SSR) bridges the gap between communications systems and classic radar systems. Despite the increasing capabilities of mobile communications, SSR remains a major component in airspace surveillance.

17-May-2021

This document is divided in two parts and starts with an introduction in AC-DC conversion principles in general. It will present the most common circuits used for different power levels. The switching mode power supply (SMPS) converter will be the main focus as they are used everywhere in the electronics. Especially the flyback converter design in different flavors are highlighted. Nevertheless, all measurements are also applicable for other SMPS converter designs operating at higher power levels.In the second part of this document, most relevant testing methods and procedures of an AC-DC converter are highlighted. For each testing section, a fundamental part will be upfront discussed and it is followed by a presentation of a suitable measurement method. In this second part, the device under test (DUT) is considered as black box device and thus the structure is similar. Therefore, the testing parts consists of methods related to input tests, output tests and a combination of both like efficiency. Of course, some test performed at the output of the converter are also relevant for DC-DC converter, e.g. the validation of the output ripple.

14-Nov-2022 | AN-No. 1SL387

長さを計測するためには 正確な定規を頼りにします。同様に 適切なプローブを正しい方法で使用することで、測定確度は向上します。

Oscilloscope bus triggering, RTO2000, bus triggering, history mode, break condition Use the hardware trigger to isolate break conditions. Break conditions can be corellated with their root cause one by one using the History Mode.

Based on the new high-performance R&S®SMW200A vector signal generator and the R&S®RTO digital oscilloscope, the solution provides MIMO signal generation and realtime channel emulation (up to 4x4 or 8x2) as well as synchronous analysis of multiple TX antenna signals.

Compliance Testing, maximum output droop, RTO, Test Mode 6 A guide to carrying out a 100BASE-T1 compliance test for the MDI return loss using an R&S®ZND 2-port vector network analyser controlled by the ScopeSuite automation software.

RTO2000, waveform display, R&S®SmartGrid, complex measurements Use the R&S®SmartGrid function to configure the display. For complex measurement tasks where several screen displays are helpful, you can superposition windows in multiple tabs. All measurement diagrams have labeled scales so you can immediately read important signal characteristics.

RTO2000, user interface, toolbar, display, cockpit The advanced user interface enables clear orientation thanks to colour coding, as well as having a high-resolution capacitive touchscreen with gesture support. The toolbar at the top of the screen provides access to frequently used functions such as measurements, zoom and FFT.