244 Results
07-Jun-2022 | Press Releases
Rohde & Schwarz enhances R&S RTP high-performance oscilloscope for even better signal integrity in real timeRohde & Schwarz has paired the outstanding performance of its established R&S RTP oscilloscope with an enhanced user interface and a larger display. The result is an even more flexible oscilloscope in a compact format with a modern look and feel that continues to deliver high-performance signal integrity in real time.
RTO/RTP Setup of Reference Levels for Measurements in Firmware Version 5
Scaling of frequency measurements RTE, RTO, RTP in cycles/min
RTE/RTO/RTP - Loading a settings file with Labview drivers
RTE/RTO/RTP - export of the history into one file with remote commands
Learn how easy it is to configure a external frontend directly by the RTP GUI. RTP Oscilloscopes with External Frontends (Part 1) The R&S FE External Frontends extend the frequency range of the RTP Oscilloscope up to 170 GHz. No additional equipment is needed for this compact and fully calibrated solution. Learn how easy it is to configure a external frontend directly by the RTP GUI.
RTE/RTO/RTP: Measurement of the level at a designated frequency in FFT with remote commands.
Describes the test procedures to perform C-PHY compliance tests.
Describes the test procedures to perform HDMI compliance tests.
Describes the procedures to perform modulated load pull measurements.
Describes the test procedures to perform DDR5 compliance tests.
Describes the test procedures to perform DDR4 compliance tests.
Describes the test procedures to perform PCIe 1.
RTP Oscilloscopes with External Frontends (Part 4 ) The RTP oscilloscope can use up to 4 external frontends to acquire the respective IF signals for further analysis. Here we use two FE44S external frontends to test a 5G FR2 signal at 28 GHz. Signal analysis is performed by the R&S VSE software running directly on the RTP oscilloscope.
Describes the test procedures to perform DDR3 compliance tests.
Learn how to do low-speed serial bus decoding with the digital channels of the RTP The 16 digital channels of the MSO option extend the measurement resources of the RTP. Use them for protocol-based triggering and decoding of low-speed interfaces such as I2C, SPI, MIL1553 or MIPI RFFE. The 16 digital channels of the MSO option extend the measurement resources of the RTP.
Describes the test procedures to perform D-PHY compliance tests.
The new RTP user interface enables a short learning curve and higher productivity. 4 12 RTP, oscilloscope, scope, MSO, user interface RTP- see the difference. Be more productive with the most intuitive oscilloscope user interface.
Additional tools such as the spectrogram illustrate the signal characteristic over time. 8 12 RTP, oscilloscope, scope, MSO, spectrum analysis, spectrogram, RF signal, wide-band RTP- see the difference. Use the accuracy of the RTP for the analysis of wide band RF signals.
Connection of R&S ScopeSuite to RTO/RTP fails
Learn about key advantages of the R&S RTP ranging from 4 to 16 GHz bandwidth The R&S RTP is the most versatile multi-purpose oscilloscope.
RTE/RTO/RTP-B6: Output of a single waveform in single mode with remote commands RTE/RTO/RTP-B6 single waveform RTE/RTO/RTP-B6: Output of a single waveform in single mode with remote commands RTE/RTO/RTP-B6 single waveform
Additionally, the acquisition of two FE110SR signals with a maximum bandwith of 10 GHz in a frequency range of 70 to 110 GHz is possible the RTP oscilloscope. RTP Oscilloscopes with External Frontends (Part 5 ) RTP Oscilloscopes with External Frontends - Automotive Radar
Describes the test procedures to perform USB 2.
Learn about the RTP toolbar.
When I use the zoom function to look at the rising edge of a rectangle signal, I see ringing which is not real, see screenshot. What is the reason?
The RTP's Zone trigger allowes as the only oscilloscope in the world to isolate events in the time and the frequency domain. 12 12 RTP, oscilloscope, scope, MSO, Zone trigger, spectrum analysis, spectrogram, RF signal RTP- see the difference. Capture infrequent events in the spectrum.
Is it possible to do math operations on a measurement? For example measure the frequency but display the result as cycles per minute?
When an additional monitor is connected via the HDMI interface, the touch functionality is lost. How can I get the touch functionality back?
Provides the information required to prepare the instrument for use and start working.