This whitepaper provides an overview of the WLAN offload in LTE as standardized by 3GPP, as well as the enhancements for Wi-Fi standardized by IEEE and the Wi-Fi Alliance. It also describes access methods in the joint network, treats the security, and describes IP mobility. In addition network discovery and selection are explained.

10-Dec-2012 | AN-No. 1MA214

The constantly increasing number of telecommunication services and subscribers is putting more and more pressure on the availability of already scarse frequencies. Authorities responsible for monitoring and regulating the radio traffic are confronted with more and more complex problems relating to radiomonitoring and frequency management. Without exact data - a prerequisite for monitoring existing installations and planning new services - it is impossible to solve the problem. It is essential to use the proper measurement equipment. This Application Note deals with the following measurements: Measuring various signal parameters at defined frequencies. Monitoring emissions for compliance with specified limits for field strength, modulation depth/index, frequency deviation and offset.

18-Jan-2002 | AN-No. 1EE13

EMI Automotive Band Evaluation extension is an on-board EMI measurement sequence in broadband and communications frequency bands for automotive and aerospace applications. This application notes shows how to configure, run, and automatically document tests in a sequence coming with EMC32-K51.

17-Jul-2014 | AN-No. 1SP07

The present application note describes the possibilities of the Stream Explorer to be remotely controlled by some peripheral program via OLE. Extensions are also discussed, widening the fields of application of such a Client-Server architecture.

31-Mar-1999 | AN-No. 7BM02

- not available -

20-Jul-2001 | AN-No. 7BM28

Nearly all tests in accordance with the Bluetooth low energy test specification V4.0 [1] can be performed using the R&S®CBT alone. Some tests additionally call for signal generators to provide interference signals. This application note describes the tests performed with additional equipment and presents straightforward solutions based on the R&S®CBTgo software.

18-Jul-2013 | AN-No. 1MA200

Femtocells or Home base stations are an important development for cellular networks. This application note describes the tests commonly used during the production of Femtocells, focusing on WCDMA, HSPA, and HSPA+ technology. Tests, test plans and hardware setups for Femtocells with and without receiver diversity are detailed. Find hints about the instrument settings and have a look at typical measurement results. An introduction to simulating GPS / A-GPS signals for testing the GPS receiver of a Femtocell completes the paper.

02-Feb-2012 | AN-No. 1MA139

Nearly all tests in accordance with the test specification* can be performed with the R&S® CMU200/CBT alone. Some tests additionally call for signal generators to provide interference signals and also require spectrum analyzers. This application note describes the tests performed with additional equipment and presents straightforward solutions based on the CBTgo software.

06-Mar-2013 | AN-No. 1MA106

The trigger is a key element of an oscilloscope. It captures specific signal events for detailed analysis and provides a stable view on repeating waveforms. Since its invention in the 1940s the oscilloscope trigger has experienced continuous enhancements. The fully digital trigger of the R&S®RTO digital oscilloscopes sets an innovation milestone that brings significant advantages for the oscilloscope user in terms of measurement accuracy, acquisition density, and functionality. This application note introduces the working principles of a conventional trigger system and explains the advantages of the real-time capable digital trigger of the RTO oscilloscopes.

11-Apr-2012 | AN-No. 1ER04

In contrast to standardized digital interfaces which are customary for communication between audio devices, diverse data formats are used between the internal modules of a particular device. The I²S interface developed by Philips has now been widely adopted for the latter. The data structure of this digital audio interface and the adaptation of Audio Analyzer UPD in the different operating modes of the I²S bus are described in this Application Note.

03-Apr-1998 | AN-No. 1GA25

This application note is a programming guide. It briefly summarizes basic tips and information about SCPI programming for remote-controlling Rohde & Schwarz signal generators.

26-Apr-2013 | AN-No. 1GP79

It is frequently desired to process the results stored on the floppy on a PC, eg for the generation of customer-specific test reports by means of a word processing system. To enable processing on an external PC, the binary data usually need conversion into an ASCII format. This is possible by means of the ESXS2ASC.EXE program. The program is available free of charge from your Rohde & Schwarz representative.

18-Jan-2002 | AN-No. 1EE21

Military satellite communications (MIL SATCOM) operators face unique challenges in maintaining reliable high-quality communications networks, particularly in remote or hostile environments. To address these challenges, the R&S®SATCOM Link Observer provides a versatile automated solution for monitoring and troubleshooting satellite communications links, ensuring efficient and effective communications networks.

03-Dec-2024

This application note shows how to perform LTE terminal block error rate (BLER) and throughput tests under fading conditions with the R&S®CMW500 Protocol Tester and the R&S®AMU200A Fading Simulator.

27-Mar-2012 | AN-No. 1MA177

The 3GPP TS 36.521-1 “Radio transmission and reception” LTE User Equipment (UE) conformance specification defines the measurement procedures for LTE terminals with regard to their transmitting characteristics, receiving characteristics and performance requirements as part of the 3G Long Term Evolution (3G LTE) standard. This application note describes how to use the LTE Frequency Division Duplex (FDD) and Time Division Duplex (TDD) measurement functionality provided by the R&S®CMW500 wideband radio communication tester to perform LTE transmitter and receiver measurements according to this test specification.

17-May-2013 | AN-No. 1CM94

- not available -

01-Aug-1997 | AN-No. 7BM39

Multiple input multiple output (MIMO) technology is an integral part of 3GPP E-UTRA long term evolution (LTE). As part of MIMO, beamforming is also used in LTE. This white paper discusses the basics of beamforming and explains the ten downlink and two uplink MIMO transmission modes in LTE Release 12.

10-Jul-2015 | AN-No. 1MA186

While RF communication signal distortions in nonlinear transmission paths have been predicted theoretically and studied experimentally for various signals, it is interesting to examine a wideband nonlinear system reaction to a wideband 3G signal and a narrowband 2G signal. Research and testing have demonstrated that, while most vital signal parameters remain within the limits specified by applicable standards even if composite signal power approaches specified maximum power, a relatively high level of spurious emissions caused by cross- and intermodulation can result. To avoid degrading both existing and new systems, this and other signal quality issues must be considered when designing and deploying multitechnology systems.

03-Nov-2006 | AN-No. 1MA110

1xEvolution – Data Optimized (1xEV-DO)is a 3GPP2 “cdma2000® High Rate PacketData Air Interface” specification. Since its introduction (Release 0), Revisions A and B have brought improvements in the data throughput in both directions and in the overall network capacity. This white paper presents the Revision A and B concepts for 1xEV-DO and explains key features.

23-Sep-2013 | AN-No. 1MA213

Broadcasting transmitters are subject to particularly stringent standards with respect to broadcast signal quality, because even small faults can lead to service disruptions for many viewers. A single instrument, the R&S®ETL TV analyzer, performs all required ATSC transmitter measurements, from the initial acceptance testing for the transmitter, to measurements performed during commis-sioning and preventive maintenance.

13-May-2013 | AN-No. 7BM102

Version 1.3.1 of the DVB-T2 standard ETSI 302 755 introduced the T2-Lite profile to ease the implementation of mobile TV services. This was achieved by minimizing the complexity of the required receiver and allowing side-by-side integration into existing conventional (T2-Base) DVB-T2 channels. For the purposes of testing the compatibility and performance of receiver modules, this application note describes how this type of composite T2-Base/T2-Lite RF signal can be simulated using one R&S®BTC or alternatively two instruments from the family of broadcast signal generators comprised of the R&S®SFU, R&S®SFE, R&S®SFE100 and R&S®SFC. Only one corresponding multiple profile T2-MI stream is required, either in the form of a file or via an external gateway.

03-Feb-2014 | AN-No. 7BM81

Broadcasting transmitters are subject to particularly stringent standards with respect to broadcast signal quality, because even small faults can lead to service disruptions for many listeners. A single instrument, the R&S®ETL TV analyzer, performs all required DAB transmitter measurements, from the initial acceptance testing for the transmitter, to measurements performed during commissioning and preventive maintenance.

24-Jul-2013 | AN-No. 7BM104

The high-definition multimedia interface (HDMI™) is used to transmit audio and video data. HDMI has become the standard for a variety of consumer electronic products, such as Blu-ray™ players, A/V receivers, set-top box, TV monitors and digital video/ still cameras. The HDMI interface measurements needed for these products require specialized T&M equipment. This equipment is not only needed for certification, but is also used for a variety of tests during development, for quality assurance and for end-of-line production testing. The R&S®VTC, R&S®VTE and R&S®VTS video testers from Rohde & Schwarz make it possible to test A/V interfaces such as HDMI easily, reliably and cost efficiently. This application note focuses on functional testing and debugging of HDMI interfaces using the R&S®VTC/VTE/VTS. It explains how these instruments can be used to assess the HDCP implementation, the ARC or the CEC functionality.

04-Jun-2014 | AN-No. 7BM85

A major US East Coast broadcast network was looking for a solution that would enable them to orchestrate multiple business units to handle the increased demand to deliver content with a very fast turnaround.

18-Nov-2014

A future-proof API to enable and streamline customized and automated workflows with Rohde & Schwarz DVS software applications.

18-Nov-2014

I/Q waveform files contain the digital complex sample values of a radio signal. They can be synthetically computer-calculated for generating precisely defined contents, or they can represent the recording of a received live signal. The structure of these files has never been standardized, which is why so many different formats are in use today. R&S®IQ Converter and R&S®IQ Stream Extractor are programs that quickly and conveniently convert the contents of I/Q waveform files of nearly any structure into the I/Q format used by the R&S®BTC, R&S®CLG, R&S®SLG, R&S®SFU, R&S®SFE and R&S®SFE100 signal generators. This makes it possible for the signal generators to use their integrated ARB function to generate precise RF signals from nearly any I/Q waveform file.

03-Feb-2014 | AN-No. 7BM79

In this application note, a UHD 4K end-to-end solution utilizing products from Rohde & Schwarz is described in detail from the point at which 4K content is captured until its delivery to households via a DVB-T2 SFN network.

29-Aug-2014 | AN-No. 7BM90

This application note describes how the transmitter landscape of a DVB-T2 single-frequency network (SFN) can be simulated in multiple input single output (MISO) mode in order to test the compatibility and performance of receiver modules. Neither an external T2-MI gateway nor a GPS receiver is required - just an R&S®BTC equipped with two RF paths. Alternatively, one R&S®SFU coupled with one or more R&S®SFU, R&S®SFE, R&S®SFE100 or R&S®SFC can also be used. R&S®ETL or R&S®ETC are suggested to fine-tune the synchronization between the generated RF signals.

03-Feb-2014 | AN-No. 7BM80

Broadcasting transmitters are subject to particularly stringent standards with respect to broadcast signal quality, because even small faults can lead to service disruptions for many viewers. A single instrument, the R&S®ETL TV analyzer, performs all required DVB-T / DVB-H transmitter measurements, from the initial acceptance testing for the transmitter, to measurements performed during commissioning and preventive maintenance.

13-May-2013 | AN-No. 7BM101

TeleZüri, Switzerland’s most successful regional TV station, has switched from tape-based operations to file-based workflows. At the same time, TeleZüri was introducing HD as standard resolution in its workflows.

18-Nov-2014