This educational note covers the theory and practice oscilloscopes based on concrete measurement examples that address authentic everyday tasks.The theoretical portion of this paper begins with an explanation of the basic operating concepts for oscilloscopes, followed by a discussion of the most important parameters to be considered when setting up and performing the exercise measurements. The practical portion of the educational note contains detailed measurement tasks that can be performed by small groups in the university lab. These exercises are intended to demonstrate and reinforce the knowledge gained in the theoretical portion. The exercises build upon one another and demonstrate measurement tasks that are frequently encountered by engineers in daily work.

16-Jan-2018 | AN-No. 1MA265

Characterizing RF mixers that have an internal LO using the value-of-three R&S®FPC1500 spectrum analyzer.

15-Oct-2018

The 3GPP TS 36.521-1 “Radio transmission and reception” LTE User Equipment (UE) conformance specification defines the measurement procedures for LTE terminals with regard to their transmitting characteristics, receiving characteristics and performance requirements as part of the 3G Long Term Evolution (3G LTE) standard.This application note describes how to use the LTE Frequency Division Duplex (FDD) and Time Division Duplex (TDD) measurement functionality associated with the Downlink Carrier Aggregation feature of the R&S®CMW500 wideband radio communication tester to perform LTE R10 receiver measurements according to this test specification.

09-Apr-2015 | AN-No. 1CM103

The present R&S®SMW-K506 Interface Control Document contains information on► the R&S descriptor word format, including ARB descriptor words and control descriptor words in deterministic and instant mode► Timing requirements and limitations of the interface► Properties of the network interface (Connector designation: HS DIGIQ).It is intended for use by customers using descriptor words to control the R&S®SMW200A in real-time. The interface control document specifies the interface between the customer’s hardware used for provision of descriptor words and the R&S®SMW200A HS DIGIQ interface. Additional information on descriptor word processing inside the R&S®SMW200A is provided.

17-Mar-2022 | AN-No. 1GP134

The R&S®SGT100A SGMA vector RF source offers a remote emulation feature that makes it possible to control the instrument by commands other than the built-in native SCPI commands. This feature allows the user to replace signal generators, e.g. from other manufacturers, with the R&S®SGT100A without having to change the remote control code. This application note describes how to use the remote emulation feature in general. Furthermore, it describes in detail the remote emulation for each supported instrument, limitations of the individual emulations and the remaining differences between the emulated and the original commands.

11-Oct-2016 | AN-No. 1GP109

Polar modulation is a method where digital modulation is realized as a combination of phase and amplitude modulation, rather than using an I/Q modulator. This technique becomes increasingly important in mobile communication. This application note shows how to generate polar modulation with an R&S®SMU200A Vector Signal Generator.

26-Nov-2004 | AN-No. 1GP58

Distortions caused by components in the RFFE (radio frequency front end) limit the performance and throughput of communications systems. Types of distortions include:▪ AM-AM and AM-PM (complex variations of gain with amplitude)▪ Non-linear frequency response (memory effect)All RFFE components exhibit all of these distortions, only the proportions vary. In this Application Note, illustrative measurements of individual RFFE components, as well as a complete RFFE, will be made. This is followed by the documentation of a more complete analysis, including comparison against theoretical limits, of a linearized commercial SatCom BUC product.

27-Feb-2017 | AN-No. 1MA299

Vector Network Analyzers of the ZVR family measure magnitude and phase of complex S-parameters of a device under test (DUT) in the frequency domain. Using an inverse Fourier transform, the results can be transformed to the time domain. The impulse or step response of the DUT is obtained, which gives an especially clear representation of its characteristics. For instance, faults in cables can be directly localized. Moreover, special time domain filters, so-called gates, can be used to suppress unwanted signal components such as multireflections.

04-Aug-1998 | AN-No. 1EZ44

Smart factories rely heavily on wireless communications technology to automate production processes and increase productivity. Any source of RF interference can disrupt the production process or delay the output.

23-Jul-2024

Application Note 1MA104 shows you how to quickly and easily create TD-SCDMA test signals for user equipment and base station tests as stipulated in the standards TS 34.122 and TS 25.142.

10-May-2007 | AN-No. 1MA104

IEEE 802.15.4 (ZigBee) uses Offset QPSK with a half-sine pulse-shaping filter as modulation. This application note describes how to set up the Rohde & Schwarz signal analyzers together with the corresponding vector signal analysis (VSA) personality for modulation quality measurements, especially EVM, for ZigBee.

12-Dec-2014 | AN-No. 1EF55

With SMIQ Signal Generator you can generate the most important Bluetooth RF test signals fast and conveniently. This application note comes with files containing modulation data for various payload patterns and burst lengths. A list of patterns is included. With the transfer software, also enclosed with this application note, you can load the data records into SMIQ and start testing immediately. BLUETOOTH is a registered trademark of Telefonaktiebolaget L M Ericsson, Sweden.

30-Jan-2001 | AN-No. 1MA31

The constantly decreasing size of components and the available board space form a challenge to place adequate test connections for RF instruments. Recent improvements in the availability and use of high performance differential building blocks in RF circuits intensify the problems of connecting test equipment. Using oscilloscope probes is a possibility to perform measurements by connecting to printed circuit board lines and chip contacts where only a minimal area is required to make contact. This application note provides information on how to use oscilloscope probes in RF measurements using spectrum analyzers, and show the results of differential measurements with a spectrum analyzer.

28-Jun-2013 | AN-No. 1EF84

With a Rohde & Schwarz oscilloscope

31-Dec-2018

Adjacent Channel Power performance of power amplifiers used in digital TV systems has to be guaranteed over a wide frequency range, 54 to 890 MHz, which may lead to time consuming test procedures. The application software described here provides swept ACP analysis, using AMIQ and SMIQ for signal generation and FSP, FSU or FSE for signal analysis. ACP measurement is performed according to FCC Regulation 47CFR 73.622(h).

16-Oct-2001 | AN-No. 1MA43

EMI debugging, FPC, FPC1000, FPC1500, EMC compliance test, EUT The combination of high power and current being sharply switched on and off has a lot of potential for EMI. EMI debugging a switched-mode power supply with R&S®FPC1000/ R&S®FPC1500 EMI debugging, FPC, FPC1000, FPC1500, EMC compliance test, EUT The combination of high power and current being sharply switched on and off has a lot of potential

30-Jun-2019

Due to its full IP system architecture and distributed infrastructure, the CERTIUM VCS is perfectly suited for integration into a virtual center.

10-Mar-2014

Compliance testing is essential to ensuring that dynamic random access memory (DRAM) signals meet the JEDEC specifications for parameters such as timing, slew rates and voltage levels. For system verification and debugging, eye diagram measurements are the most important tools for efficiently analyzing the signal integrity in any digital design. The specific nature of DDR requires a dedicated solution with a powerful read/write separation to get meaningful eye diagrams on the DDR data bus.

19-Feb-2019

The R&S MATLAB® Toolkit for R&S® NRP-Z Sensors provides routines for remote controlling these instruments via USB or the R&S® NRP Power Meter. This application note describes how to access the sensors using the R&S® VXI PnP driver. It also contains a set of scripts that perform commonly needed tasks, such as opening a sensor connection or performing measurements.

05-Mar-2011 | AN-No. 1GP61

This application notes describes remote operation or monitoring of the spectrum analyzers R&S® FSL3, R&S® FSL6, R&S® FSL18 through a standard web browser. The common cross-platform technology Virtual Network Computing (VNC) is used as a server on the instrument.

07-Jan-2009 | AN-No. 1EF66

A measurement campaign quantifying the impact of intermodulation in 5G TDD networks

Critical infrastructure: With the deployment of TDD networks, the mobile network community recognizes the critical importance of cell synchronization and the use of uniform TDD patterns across different networks for the proper operation of mobile radio networks. Variety of scenarios: Possible scenarios include cross-border situations, interactions between private campus networks and public mobile networks, and accidental synchronization chain breaks or misconfigurations within the mobile network.Measurement techniques: To quantify the effects of non-synchronized cells and using different TDD pattern in neighboring networks, R&S, in collaboration with TU Dresden and Advancing Individual Networks GmbH (AIN), conducted a measurement campaign using movable networks with full control over all network parameters. This campaign measured the effects on uplink and downlink throughput, mapping these to RSSI/RSRP values received at the interfered site.Customer benefits: The available quantification is valuable for predicting and assessing potential interference scenarios before setting up and operating a new cell site.

11-Sep-2024 | AN-No. 8NT18

This application note describes how to use the generic interface in R&S®AdVISE for remote operation.

19-Jun-2020 | AN-No. 1S002

This Application Note briefly explains the theoretical background regarding phase noise before describing the phase noise option for the R&S SFU. You will see how the phase noise profile creator application software can be used to generate specific phase noise curves and how to output them with the aid of the R&S SFU.

22-Aug-2007 | AN-No. 7BM63

Using a Vector Network Analyzer from the ZVR family, not only magnitude and phase can be measured, but also group delay and even phase delay. Whereas phase delay measurements produce the highest accuracy for the electrical length of non-dispersive devices under test, such as coaxial cables, group delay measurements also give a detailed insight into the frequency dependent delay characteristics of dispersive devices, such as filters. In addition to the traditional step aperture technique, Vector Network Analyzers from the ZVR family offer a frequency aperture technique, which allows a well defined and constant aperture for group delay measurements also for a nonlinear frequency sweep.

28-Jul-1998 | AN-No. 1EZ35

For establishing a WLAN connection between R&S®CMW and device under test (DUT), the WLAN properties at the R&S®CMW have to be adapted to the test conditions. These can vary in several aspects, particularly due to the different WLAN standards and characteristics of the DUT. This document describes the critical parameters and provides step-by-step procedures for the configuration.

08-Dec-2015 | AN-No. 1C106

How I/Q noise cancellation can help significantly improve the EVM performance of your signal and spectrum analyzer.

16-Nov-2023

The Rohde & Schwarz power consumption analysis tool helps evaluate power consumption data collected with Rohde & Schwarz power supplies.

01-May-2023

The R&S®SMB100A RF and microwave signal generator offers a remote emulation feature that makes it possible to control the instrument by commands other than the built-in native SCPI commands. This feature allows the user to replace signal generators, e.g. from other manufacturers, with the R&S®SMB100A without having to change the remote control code. This application note describes how to use the remote emulation feature in general. Furthermore, it describes in detail the remote emulation for each supported instrument, limitations of the individual emulations and the remaining differences between the emulated and the original commands.

20-Mar-2012 | AN-No. 1GP89

The R&S® ZVA-Z110 converters offered for the R&S® ZVA family enable network analysis in the W band (75 GHz to 110 GHz). In this Application Note, measurements with three or four converters will be discussed. Test configurations for such measurements have so far been implemented only with coaxial connector systems for a frequency range up to approx. 40 GHz. The term 'multiport measurements' was created for this type of measurements.

09-Oct-2007 | AN-No. 1EZ56

IoT devices have tight requirements for power consumption in order to achieve expected battery life times of multiple years without a connection to a power supply. In order to verify the power consumption and expected battery life time, voltage and current have to be measured accurately for different operating states of the device under test.This application note explains battery life tests using RT-ZVC in combination with CMWrun and CMW500, including example applications.The solution by Rohde & Schwarz enables precise voltage, current and consequently, power measurements.The RT-ZVC Multi-Channel Power Probe can be driven as part of a test plan combining signaling and power measurements for a detailed view of the power consumption in different signaling states as well as an estimation of overall lifetime given a certain battery capacity.

17-Feb-2017 | AN-No. 1MA281