Power converter and inverter designs for higher power levels are usually based on hard switching half bridge configurations. In such setups, users must pay particular attention to proper switching operations to prevent shoot-through events. Setting up complex real-time trigger conditions using the R&S®RTE and R&S®RTO oscilloscopes increases the test coverage and robustness of converter and inverter systems.

10-Aug-2020

The Federal Communications Commission (FCC) ruled that no later than February 17, 2009, all analog NTSC broadcasting must come to an end. It is therefore not surprising that the demand for ATSC receivers is high at the time this application note was published. ATSC TV sets and set-tops are subject to the ATSC recommended practice Doc.A/74 “Receiver Performance Guidelines” before they can be sold freely in the markets that adopted the standard. Although the number of tests defined in Doc.A/74 is less extensive then the ones for their DVB-T counterparts (EN62002, MBRAI), some clarification is nevertheless due.

27-Sep-2012 | AN-No. 7BM71

This application note provides an introduction to the DDR memory technology and explains common challenges, related to the specific nature of DDR data, command / address and control buses and describes the typical measurements to verify and debug DDR system designs.The paper explains the recommended test points and the connection of oscilloscope probes as well as the compensation of effects from DDR interposers via deembedding. The document describes efficient Signal Integrity verification with eye diagram measurements, advanced triggering and TDR/TDT functionality. Given the high number of signal lines and the dynamic bus termination, SSN (simultaneous switching noise) has a significant effect in DDR memory designs and Signal Integrity as well as Power Integrity is highly pattern dependent. We introduce techniques to achieve high acquisition rates and help to efficiently detect worst case scenarios, affecting the performance of the overall memory design. The document also includes a close look on Power Integrity.Providing best practice examples in the design verification and debugging process, the document addresses all system designers and test engineers, working on DDR memory designs.

30-Oct-2020 | AN-No. GFM340

Taking the R&S ESR EMI test receiver as an example, this paper looks at a CISPR 16-1-1- compliant test instrument with time domain scanning capabilities. The paper compares the measurement speed and level measurement accuracy of a conventional stepped frequency scan versus an advanced FFT-based time domain scan. It also contains guidance on making optimum use of time domain scans.

29-Jan-2014 | AN-No. 1EE24

R&S®SITLine ETH protects against spionage and manipulation without decreasing throughput.

03-Mar-2015

The R&S®NRP-Z power sensors from Rohde & Schwarz represent the latest in power measurement technology. They offer all the functionality of conventional power meters, and more, within the small housing of a power sensor. This application note serves as a coding guide for situations in which the R&S®NRP-Z power sensors are to be used in custom test and measurement software.

06-Mar-2012 | AN-No. 1GP69

Combining the R&S®Pulse Sequencer software with one of the vector signal generators from Rohde & Schwarz is the perfect solution for defining and playing pulses.

09-May-2017

This application note describes how to measure the coherence (phase-, timing and gain-differences) between two RFSignals using Rohde&Schwarz spectrum analyzers, a Rohde&Schwarz signal generator and the R&S FS-Z10 Coherence Unit.

28-Sep-2010 | AN-No. 1EF70

The R&S®VTC/VTE video testers analyze and evaluate the quality of set-top boxes and TVs on the DUT’s A/V interfaces from a user perspective. They provide the necessary quality tests from Go/NoGo tests to long-term stability tests. The RF input signals required for the DUT are generated by the R&S®VTC/VTE.

04-Feb-2014

Validating switching converter stability is vital for any power supply design. Frequency loop and load transient responses are often used to ensure switching converter stability. Even as frequency loop response becomes more important to design validation, load transient response is still commonly used. Load transient response can also be enhanced by visualizing the positive duty cycle for pulse width modulation (PWM) signals over time. A modern oscilloscope can do this, while also helping identify unknown converter effects.

09-May-2023

1SL391 audio, breakthrough, ETSI EN 301 489 Audio Breakthrough Assembly and Test Setup 1SL391 audio, breakthrough, ETSI EN 301 489

11-Oct-2022 | AN-No. 1SL391

Spectrum Rider, FPH, FSH, ZPH, Cable Rider, ZVH, 5G, Interference hunting, Zero span mode, G NR TDD signal Handheld solutions from Rohde & Schwarz support a gated trigger, enabling users to separate uplink and downlink signals in the time domain. 5G NR – interference hunting in the uplink of TDD networks Spectrum Rider, FPH, FSH, ZPH, Cable Rider, ZVH, 5G, Interference hunting, Zero span mode, G NR

09-Apr-2019

Sequencer Software Tool

14-Mar-2016

This document describes typical measurements that are required to be made on amplifiers and how the measurement can be implemented on the ZVB Vector Network Analyzer. The document describes the concepts and setups required to perform Gain, Isolation, input impedance measurements, then goes on to describe how more uncommon measurements are made with the ZVB like Harmonics, Stability Factor and compression point.

07-Feb-2007 | AN-No. 1EZ54

Integrated end-to-end data solution with IP traffic analysis and protocol statistics allows detailed analysis of data traffic generated by IoT and mobile devices.

06-Jun-2017

This Application Note describes how to configure and calibrate R&S ZVR network analyzers for conversion gain measurements of devices with two ports that have different impedances. Thus accurate measurements on frequency-converting devices such as low noise converters of sattellite receivers are possible.

16-May-2002 | AN-No. 1EZ50

This application note describes measurements compliant with the cdma2000 standard described in TIA/EIA-97-C and TIA/EIA-98-C. The primary focus is on solutions for generating and analyzing cdma2000 signals with equipment from Rohde & Schwarz. The special characteristics that make the signal generators and signal analyzers eminently suitable for this purpose are detailed.

27-Mar-2001 | AN-No. 1MA34

Analyzing high speed datacom interfaces is an important task and ensures signal integrity. One major challenge of this analysis is the connection between the physical interface and the oscilloscope, as most of the datacom interfaces do not provide test connections suitable for RF. A test fixture is required as a bridge between the high speed datacom IF and the RF connector of the oscilloscope, but this will affect the signal integrity measurement. The R&S®RTP and R&S®RTO oscilloscopes with the advanced jitter option can analyze and separate jitter contributions. Additionally, the option can evaluate the impact of test fixtures and traces inherently and give the user a good understanding of the impact of their test setup.

15-Jul-2024

The advanced generation capabilities of the R&S®SMW200A vector signal generator simplify receiver testing up to 20 GHz by removing the need for multiple signal generators. This single-box solution brings the real world into your lab.

05-Aug-2014

During the design process of chipsets or modules, FPGA-based hardware emulators are utilized to perform early tests with real test and measurement instruments. These hardware emulators usually run at artificially reduced speed, but apart from that function like the finished design. In this application note we explain how to test FPGA-based hardware emulators using Rohde & Schwarz vector signal generators for creating suitable real-time test signals at reduced sample rates. We further explain how to correctly adapt AWGN signal generation and fading simulation for “slow I/Q”.

10-Dec-2012 | AN-No. 1GP95

Signal generators are often used in automated test environment applications. The replacement of those instruments, e.g., due to malfunction or standard replacement procedures requires special care to be taken in consideration. Replacement of those instruments requires compabitiblity between the replacement and the replaced device in at least the electrical and remote-control features. This application note describes in detail how to use the emulation modes of the R&S® series SMA100A, SMB100A, SMF100A signal generators.

24-Jun-2008 | AN-No. 1GP71

LTE user equipment (UE) receiver performance has significant impact to cellular radio network coverage and capacity. It determines the maximum data throughput across the air interface between the LTE base station (eNB, evolved node B) and the mobile network subscriber UE, thus it determines the total capacity across the air interface. Therefore, it is one of the most important measurements to verify the actual receiver performance of individual devices, and a key metric to compare different devices, in particular.This paper shall give an introduction to receiver performance measurements and discusses the measurement metrics as well as the challenges of over the air (OTA) measurements.

31-Aug-2017 | AN-No. 1ST001

This application note describes how to directly transfer S-Parameter Trace Data from R&S Network Analyzers to Microsoft Excel using a direct connection like GPIB or LAN. Prerequisites are a PC running Microsoft Excel, a R&S Network analyzer like ZVA, ZVB or ZVT as well as a working remote control connection between PC and instrument like GPIB or LAN / Ethernet.

22-Mar-2007 | AN-No. RSI02

Broadband amplifiers are necessary for generating the field strengths required for most EMC radiated immunity tests. This Educational Note provides a brief overview of the role of amplifiers in EMC testing as well as a discussion of the parameters and characteristics which have the greatest influence on amplifier performance.Register now to download the Educational Note.

01-Aug-2022

The R&S®Pulse Sequencer software offers an interface to import lists of pulse descriptor words (PDW). Users can define their specific PDW format in the software before importing the PDW list. The R&S®Pulse Sequencer software automatically uploads the interpreted PDW lists on the R&S®SMW200A to generate the most agile radar signals.

20-Feb-2018

To analyse the quality of tuners, lots of measurements have to be done. This application note presents a program, which combines these measurements to an automatically running sequence and gives a printout of the results. In addition, it explains the measurements and informs about the different standards.

16-Feb-1998 | AN-No. 1GA24

For automated test applications, measurement time is often as important as the quality of the measurement. As with many situations, time is money. In practice, phase noise measurements are generally not considered fast, but test engineers still desire to save as much test time as possible. The Rohde & Schwarz®FSWP (FSWP) is a modern, digital signal processing based, phase-noise test set that performs many tasks in parallel in an effort to improve measurements speed. However, several measurement settings drastically affect measurement speed. This paper will discuss these settings and provide suggestions on improving overall measurement speed.The three key instrument parameters that affect FSWP measurement speed are:1. Number of cross correlations2. Resolution bandwidth (RBW)3. Offset frequency span

08-Oct-2020 | AN-No. GFM354

This Application Note gives an introduction to measurements of WiMAX signals according to standards 80216-2004 and 802.16e-2005. It describes all kind of signal generation from simple signals to multiple-zone signals, also under multipath environment (fading), and covers all signal measurements from power and spectrum analysis, crest factor and CCDF measurement down to bit pattern analysis and modulation measurements.Please see also 1MA96 for General information about the WiMAX standard and 1EF57 for an introduction to the WiMAX standard.

10-Jul-2006 | AN-No. 1MA97

An FSE (or FSIQ) Spectrum Analyser equipped with the Vector Analysis option (FSE-B7) can measure a wide range of error types (EVM, Magnitude Error, Phase Error…) on continous signal. This Application Note describes how to measure these errors on a single burst between symbols.

22-Jan-2011 | AN-No. 1ES48

This application note shows all necessary settings for performing Dual Receiver Measurement using the R&S®EMC32-K27 option via R&S® EMC32 Measurement Software.

28-Sep-2017 | AN-No. 1SP20