153 Results
Cannot use internal display and external monitor together at the same time.
What is the function of "Resolve pool link" in the calibration manager?
Converting the real and imaginary numbers to magnitude in dB and phase in degrees.
Provides basic information on the calibration kits R&S®ZCWM-570.
Describes all instrument functions.
What is the correct pin layout of the DC inputs on the network analyzer's rear panel?
Sending a remote Control Command internally
I have set my VNA to single sweep mode and switched on averaging with a factor of 10. But when I restart the single sweep, it stops after 1 sweep and the averaging is not done.
Provides information on security issues when working with R&S®ZVAX-TRM in secure areas.
Describes all instrument functions and remote control commands, as well as measurement and programming examples.
Provides the information required to prepare the instrument for use and start working.
Provides the information required to prepare the instrument for use and start working.
This application note describes how to configure a Rohde & Schwarz Network Analyzer to make spectral measurements directly on a device under test.
16-Mar-2012 | AN-No. 1EZ62
I query the values of a trace using scpi commands. But I get the y-values only. Is there a possibility to get the y-values also (frequency)?
I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.
I trigger this single sweep with the RSZVB_Send_Trigger_and_Wait_for_OPC driver, but this driver does not wait for the complete 10 sweeps. If I don't use averaging, this program is works.
How can I switch from remote to local state via remote control?
TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines
How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?
The R&S®ZVA vector network analyzer in combination with the R&S®ZVAB-K30 noise figure measurement option simplifies noise figure measurement, a key parameter for receiver performance evaluation.
TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.
This application note describes the techniques to measure the dielectric properties of materials using a vector network analyzer. It also shows methods for converting the s-parameters to dielectric properties.
23-May-2012 | AN-No. RAC-0607-0019
Provides basic information on the calibration kits R&S ZV-Z129, ZV-Z135 and ZV-Z170.
Provides basic information on the calibration kits R&S®ZV-WR02, R&S®ZV-WR03, and R&S®ZV-WR05.
ZVA Vector Network Analyzers, PIM, Rohde & Schwarz demonstrated fast and accurate passive intermodulation (PIM) testing of duplex filters at the European Microwave Week 2013 in Nuremberg.
Provides basic information on the calibration kits R&S®ZV-WR06, ZV-WR08, ZV-WR10, ZV-WR12, ZV-WR15.
I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?
Provides basic information on the calibration kits R&S®ZN-Z170, ZN-Z135, ZN-Z129 and ZN-Z129E.