9087 Results
Simultaneous simulation of all important constellations and frequency bands makes the GNSS simulator in the R&S®SMW200A the perfect solution for testing your GNSS receiver in the lab.
11-Sep-2018
Measurement of Transient Responses in AGC Circuits using the Audio Analyzers UPL and UPD
04-Jun-1998 | AN-No. 1GA32
This application card will give some guidance as to the possible combinations of bandwidth options and mixers in conjunction with the needed IF frequencies.
16-Jun-2020
You need a flexible clock source that can provide the signals needed for today’s and tomorrow’s designs with minimal jitter and noise as well as best spectral purity.
03-Aug-2017
Selecting Your Next Oscilloscope:
If you are selecting your next oscilloscope and want more insight on how to understand ENOB values measured and published by oscilloscope manufacturers, this document is for you. The effective number of bits (ENOB) is a way of quantifying the quality of analog to digital conversion. A higher ENOB means that voltage levels recorded in analog to digital conversion are more accurate. Understanding oscilloscope vendor-supplied ENOB values can be complex. This document focuses on interpretation of measured ENOB results made on oscilloscopes rather than the math behind ENOB calculations.
21-Jun-2024 | AN-No. 1TD12
An offline AC/DC switching converter has no separate bias power supply that provides power to the control integrated circuit itself. Here, an auxiliary primary winding and discrete components are added to supply power to the control circuit. Verifying this circuitry is essential and requires accurate and detailed signal level and timing measurements. The startup sequence takes a long time, which needs to be taken into consideration in the measurement and requires an instrument with sufficient memory.
23-Nov-2022
Accessing Measurement Data and Controlling the Vector Network Analyzer via DDE
31-Jul-1998 | AN-No. 1EZ33
Remote Emulation with the R&S SMBV100B Signal Generator
30-Sep-2019 | AN-No. 1GP121
RF system noise contributions define receiver capabilities and sensitivity. The noise figure measures how the critical components affect the signal.
28-Jan-2022
Double frequency range for R&S Signal Generators
20-Apr-1998 | AN-No. 1GPAN03
This document describes WLAN tests which rely on communication (signaling) between R&S CMW and device under test (DUT) and on transmission of packet data over WLAN. On the R&S CMW side the WLAN Signaling application is required, for some tests also the Data Application Unit (DAU). The test principles and the necessary settings are explained and background infor-mation is given. Step-by-step procedures are provided for the main configuration tasks.
08-Feb-2016 | AN-No. 1C107
Generation and Analysis of ZigBee™ IEEE802.15.4 signals in the 2.4 GHz band
21-Jun-2007 | AN-No. RSI03
The topic of this application note is mobile phone measurements – in theory and in practice. It discusses measurements according to the most common standard in use today, GSM.
22-Aug-2014 | AN-No. 1MA231
The R&S®Pulse Sequencer software together with the R&S®SMW200A vector signal generator offers a simple and easy way to simulate multi-emitter environments.
13-Nov-2018
Rohde & Schwarz Drivers under VEE - Installation and Troubleshooting
20-Dec-2012 | AN-No. 1MA035
Multichannel signal reception in parallel using digital downconverters in a monitoring receiver.
14-May-2014
Welcome to this introductory video show about the R&S ZVA family of network analyzers.
13-Feb-2014 | AN-No. 1MA50
High-speed serial interfaces often transmit data with differential signaling and differential probes can be used to access signal traces. In addition to differential inputs, these probes have a ground connection.
02-Nov-2022
Testing radar warning equipment in realistic scenarios is crucial to reliable field performance. Commercial vector signal generators (VSG) such as the R&S®SMW200A from Rohde & Schwarz have become a very attractive alternative thanks to their increased available bandwidth and processing power.
13-Aug-2020
This application note explains how to setup R&S®AdVISE to monitor the temperature of an EUT by using an infrared camera.
14-Sep-2020 | AN-No. 1S008
In this paper we will review the basics of spurious measurements and how the parameters used can affect the detection performance.
14-Jul-2017 | AN-No. 1EF97
Verifying RF ports is crucial for minimizing lost power and maximizing battery life. The R&S®FPC1500 is an easy-to-use and costeffective tool for this type of verification.
05-Mar-2020
For measurement settings below 10 mV/div, oscilloscopes typically reduce the measurement bandwidth in order to keep the trace noise as low as possible. The R&S®RTO is different: It offers the full bandwidth even for the most sensitive settings, and an A/D converter with more than 7 effective bits (ENOB) digitizes the signal.
13-Jul-2012
Remote Emulation with the R&S<sup>®</sup>SMA100A Signal Generator
17-Aug-2015 | AN-No. 1GP93
Measurements on PCS1900 Mobile Stations According to J-STD-007
01-Nov-1996 | AN-No. 1EF22
In this application note the fundamental working principles of active antennas and the differences compared to passive antennas are asserted.
03-Feb-2016 | AN-No. 8GE02
The R&S®SMBV100B delivers precise synchronization information for communications in C-V2X mode and very accurate position information to the device under test.
18-Nov-2019
The R&S®RTx-K50 option expands the addressable range of interface standards by adding decoding capability for standardized and proprietary Manchester or NRZ coded buses.
19-Oct-2020
The R&S®SMB100A analog signal generator is the ideal calibration source for weather radar receivers due to its highly accurate output level.
25-Jan-2011
CDMA2000 1xEV-DO Packet Data Testing with R&S<sup>®</sup> CMU200
04-May-2007 | AN-No. 1CM64