124 Resultados
Perguntas frequentes; A resposta do software de monitoramento externo não aparece na janela do EMC32. Qual a origem desse problema?
Amplificador genérico e R&S®EMC32, diferentes formas de enviar comandos SCPI em sequência
Nível de imunidade não alcançado - anular escaneamento de EMS
After calibration I received updated attenuation and transducer tables. How do I enter these values into the EMC32 Explorer to continue new Tests with these values?
EMC32: Interactive data reduction, difference between "After data reduction" and "Before final measurements".
Perguntas frequentes; Por que vejo somente uma Tabela de resultados no explorador do EMC32 apesar de eu definir dois detectores?
Perguntas frequentes; Toda vez que eu inicio meu EMC32, surge um erro estranho: “ikey for AMS32 could not be found” (“o ikey para R&S®AMS32 não pôde ser encontrado”). O que fazer?
Inicializar o gerador de RF, alterar o nível de inicialização para testes de imunidade usando o EMC32
Saiba mais sobre como solucionar o problema, caso receba a seguinte mensagem de erro ao inicializar o EMC32 "A aplicação será encerrada".
Perguntas frequentes: Verifique as expansões do EMC32
So far I only have experience how to add a transducer to a slidebar, a 2-Line-LISN or 4-Line LISN. Now, I want to add a transducer for an 8-Wire ISN (e.g. ENY81) to EMC32.
EMC32, display preview results of all LISN phases
Enviar frequência e nível do EMC32 para o Vector CANoe.
EMC32, intervalos de frequência na pesquisa de máximas em subintervalos
Essa nota de aplicação mostra como configurar, calibrar e executar medições de suscetibilidade eletromagnética (EMS) conduzidas de acordo com IEC/EN 61000-4-6 e medições de EMI de acordo com CISPR 16-2-1 com a ferramenta de software R&S®EMC32.
jul. 19, 2013 | AN-Nº. 1MA212
Use of the ESW build in Pulse Limiter, if remote controlled by EMC32
Quando eu executo o teste e volto para alterar os parâmetros no modelo de teste, como salvar as novas configurações?
EMC32, Download Transducer Factor to Test Receiver
Vou migrar o sistema EMC32 no ELEKTRA usando a ferramenta de migração. Parece que a ferramenta de migração tem um problema ao ler o DeviceList.
EMC32 measurements with more than 1000000 points
O que posso fazer para configurar um transdutor válido?
EMC32, Level Sweep shape during Reference Calibration
Estou utilizando minha plataforma giratória e o alinhamento final funciona em faixa completa (entre -180 e +180°), então eu defini uma "predefined range" de 60°-
Perguntas frequentes: Quando preciso da Administração de usuário do EMC32?
É possível implementar uma plataforma giratória que possa ser controlada utilizando o software EMC32 com meu receptor de EMI?
How can I add a attenuation table to my cable, used in my measurement setup?
Using R&S®ELEKTRA Migration Tool
The R&S®ELEKTRA EMC test software is the successor of the R&S®EMC32 EMC measurement software. Like the R&S®EMC32 EMC measurement software, the R&S®ELEKTRA offers a solution that controls complete EMC systems and automates measurements on equipment under test (EUT) that is being tested for emissions (EMI) and immunity (EMS) compliance. It has more features and test types compared to R&S®EMC32.As both software platforms use different file formats, R&S®EMC32 users who upgrade their existing software to the R&S®ELEKTRA platform need to perform a file conversion before migrating their data to the R&S®ELEKTRA platform. This is done by using the R&S®ELEKTRA Migration Tool, which is installed automatically with each R&S®ELEKTRA installation.This Application Note describes how to use the R&S®ELEKTRA Migration Tool (version 4.4 onwards) for converting the backup data into the XML format that can be interpreted by the R&S®ELEKTRA software. It also provides recommended conversion steps (Chapter 5) and troubleshooting tips (Chapter 6). For instructions on migrating the data using R&S®ELEKTRA Migration Tool below version 4.4, refer to the R&S®ELEKTRA user manual. For better user experience, we recommend using the latest software version for migration.This Application Note does not describe the steps to backup data using the R&S®EMC32 or R&S®ES-SCAN software. For procedures on how to do so, refer to their respective manuals.
May 04, 2023 | AN-Nº. 1SL396
Mostrar o gráfico de um transdutor usando o EMC32
Nos gráficos de um teste, é possível deixar a legenda sempre ativada? De forma que não seja mais necessário inseri-la toda vez que um teste for concluído?
Atualizando as macros API no EMC32