35 Risultati
Come è possibile passare dall'impedenza di ingresso di 50 Ohm a quella di 1 MOhm utilizzando un comando SCPI?
RTO / RTP Firmware Update from an older Version
WEB control is not working with the RTO.
Which test fixture for MDI mode conversion measurement at 100Base T1 Compliance Test?
Esportazione di canali analogici e digitali della stessa acquisizione
RTE/RTO/RTP - esportazione della cronologia in un unico file con comandi remoti
Is it possible to do math operations on a measurement? For example measure the frequency but display the result as cycles per minute?
Quando si imposta la frequenza portante e la larghezza di banda del filtro, si riceve l'avviso CF + BW/2 > DevBW.
The Zoom function does not show any waveform data at specific settings, especially at slower timebases in combination with higher sample rates, High resolution and roll mode with more channels. The problem is gone if a lower sample rate is chosen.
RTE/RTO/RTP: Misura del livello a una frequenza designata nella FFT con comandi remoti.
A sinus signal with i.e. 10 V peak-peak, frequency 1 MHz is applied. If I choose a vertical scale which is too small the peaks of the waveform are not displayed as they are out of range. Now I activate the digital filter in the “Vertical” menu à “Channel”. The frequency of the filter is also set to 1 MHz. Now even at very small vertical scales (i.e. 50 mV/div) the waveform is displayed completely, see screenshot. But the amplitude can not be correct. What goes wrong here?
Sto utilizzando la modalità di ultra segmentazione per ridurre al minimo il tempo cieco. Ma questo non è indicato. Esiste un modo per calcolarlo?
Configurazione degli oscilloscopi RTO/RTP: livelli di riferimento per le misure nella versione 5 del firmware
I want to export the waveform data of my RTO scope into MATLAB, but the only way I found so far is the screenshot option. Is there another way to use the trace data in my script?
Esempi di programmazione per oscilloscopi.
Numero di armoniche, RTE, RTO,Opzione di potenza, Domande frequenti
RTE/RTO/RTP - Caricamento di un file di impostazioni con i driver di Labview
Accuracy of RMS Measurements
R&S Scope Suite - Error communicating with oscilloscope
Vogliamo misurare la tensione della linea di alimentazione di rete con il nostro oscilloscopio.
All'avvio di RTE/RTO/RTP Windows richiede utilizzatore e password. Come posso ripristinare la funzione autologon?
Regolazione del volume del “BEEP”
Il collegamento con R&S ScopeSuite all'oscilloscopio RTO/RTP non riesce
La sequenza SCPI per la configurazione e l'interrogazione dei dati per l'opzione K11 dell'interfaccia software I/Q.
Collegamento del dispositivo in prova e del partner di collegamento con l’attrezzatura di prova RT-ZF2
Collegando un monitor esterno tramite l'interfaccia HDMI, si perde la funzionalità touch. Come posso ripristinare tale funzionalità?
Serve sempre un dongle di licenza FSPC (1310.0002.03) per far girare il software FS-K96?
FAQ - Decoding of SENT protocoll shows CRC errors
Quando utilizzo la funzione di zoom per osservare il fronte di salita di un segnale rettangolare, vedo un'interferenza che non è reale, vedere la schermata. Perché?
R&S Scope Suite - Test di conformità eMMC non riuscito
I have exported the waveform into a csv file. When I open the file in Excel, the values are completely wrong. How can I get correct values?
Ho confrontato sonde passive e attive. Sembra che con le sonde attive il rumore sia maggiore. Qual è il motivo e cosa posso fare per ridurre il rumore?
Cambio scale delle misure di frequenza con gli oscilloscopi RTE, RTO, RTP in cicli/min
For some tests a vector network analyzer is required. The Scope Suite software just supports VNAs from R&S to be connected via LAN for automated measurements. Can I use also other VNAs and do the measurement manually?
When I do RMS measurements and an offset is applied, the result changes. I could not see that effect on other scopes. What is wrong here?