26 결과
높은 임피던스를 갖는 오실로스코프에서 RT-ZD02 또는 RT-ZD08 차동 프로브를 사용할 수 있나요? RT-ZD02/ZD08의 임피던스는 50 Ohms입니다.
How to store results on a local PC from a RTB connected via LAN.
RUN 연속 모드에서 오실로스코프를 사용합니다. "STOP"을 누르면 하나 이상의 획득(acquisition)이 표시되며, 파형이 오버레이됩니다. 오버레이를 방지할 수 있는 방법이 있습니까?
"ZZA-RTB2K" 랙마운트 키트를 사용해서 RTB/RTM/RTA를 랙에 설치하고 싶습니다. 오실로스코프 접지가 랙 프레임에 연결되나요?
오실로스코프의 델타 시간 정확도 계산
RTB, RTM, RTA: Acquire Mode "High Resolution" looses details?
I do RMS measurement on a signal after switching the channels. Even with *OPC? or *WAI the result is implausible: 9.91e+37 . How can I get a correct result?
이전 스코프에서는 X/Y Mode를 실행하는 데 트리거가 필요하지 않았습니다. 현재는 유효한 트리거 조건이 감지되지 않으면 X/Y Mode가 작동하지 않는데, 이유가 무엇인가요?
When I query the waveform with "CHANx:DATA?" the resolution is just that what is displayed on the screen. But I have manually changed the record length to achieve a high resolution. How do I get the data of the waveform with full resolution?
교정 성적서 Calibration certificate; ZNL; ZNLE; FTP1000; RTH1000; RTB2000; ZPH; FPH; FPC1000; RTM3000 교정 성적서 Calibration certificate; ZNL; ZNLE; FTP1000; RTH1000; RTB2000; ZPH; FPH; FPC1000; RTM3000
How can I query the waveform data of the serveral segments?
LabView Driver rsrtx - Range of Configure Trigger Channel Level
I would like to measure the voltage at a certain time of a captured waveform. Do I need to use the cursor function? May I ask for the SCPI commands?
No synchronisation in Auto Trigger Mode
RTB/RTM/RTA - FFT에서 Stop Frequency 감소
임의 파형 발생기의 주파수를 10 kHz로 설정하면 출력 신호 주파수가 120 kHz가 됩니다. 무엇이 잘못된 건가요?
원격 명령으로 트리거 상태 쿼리를 실행하는 방법은 무엇인가요?
오실로스코프 프로그래밍 예제.
RTB/RTM/RTA: 채널에서 V 또는 A를 제외한 다른 단위 선택 RTB, TRM, RTA RTB/RTM/RTA: 채널에서 V 또는 A를 제외한 다른 단위 선택 RTB, TRM, RTA
How can I find out that the measurement has been finished?
오실로스코프를 사용하여 메인 라인의 전압을 측정하고자 합니다.
Saving a screenshot to an USB stick with remote commands
활성 FFT를 사용하는 경우 시간축 설정 변경이 불가능합니다. 문제를 해결할 방법이 있습니까?
/INT/SCREEN 경로에 중요한 스크린샷을 몇 개 저장했습니다. 이 데이터를 USB 또는 PC에 저장/복사하려고 합니다.
I have exported the waveform into a csv file. When I open the file in Excel, the values are completely wrong. How can I get correct values?
Instrument View의 "Remote Display" 기능을 사용하고 싶습니다. 그런데 화면이 나타나지 않고 "화이트" 영역만 표시됩니다. PC는 USB를 통해 연결되어 있습니다. 사용법을 확인하고 싶습니다.