35 결과
RTE/RTO/RTP - 히스토리를 원격 명령으로 하나의 파일로 내보내기
Which test fixture for MDI mode conversion measurement at 100Base T1 Compliance Test?
RTE/RTO/RTP: 원격 제어를 통해 FFT에 입력된 주파수에서의 레벨 측정
Export of analog and digital channels of the same acquistion
SCPI 명령어를 사용해서 50 Ohm 및 1 MOhm 입력 임피던스를 전환하는 방법
RTO/ RTP 펌웨어 업데이트
Is it possible to do math operations on a measurement? For example measure the frequency but display the result as cycles per minute?
I want to export the waveform data of my RTO scope into MATLAB, but the only way I found so far is the screenshot option. Is there another way to use the trace data in my script?
블라인드 타임을 최소화하기 위해 Ultra Segmentation 모드를 사용하고 있습니다. 그런데 블라인드 타임이 표시되지 않습니다. 블라인드 타임을 계산할 수 있는 방법이 있습니까?
캐리어 주파수와 필터 대역폭을 설정하면 "CF + BW/2 > DevBW" 경고가 표시됩니다.
A sinus signal with i.e. 10 V peak-peak, frequency 1 MHz is applied. If I choose a vertical scale which is too small the peaks of the waveform are not displayed as they are out of range. Now I activate the digital filter in the “Vertical” menu à “Channel”. The frequency of the filter is also set to 1 MHz. Now even at very small vertical scales (i.e. 50 mV/div) the waveform is displayed completely, see screenshot. But the amplitude can not be correct. What goes wrong here?
The Zoom function does not show any waveform data at specific settings, especially at slower timebases in combination with higher sample rates, High resolution and roll mode with more channels. The problem is gone if a lower sample rate is chosen.
RTE/RTO/RTP - Labview 드라이버를 통한 설정 로드
Accuracy of RMS Measurements
WEB control is not working with the RTO.
측정을 위한 RTO/RTP 레퍼런스 레벨 셋업(펌웨어 버전 5)
R&S Scope Suite - eMMC 컴플라이언스 테스트 실패
Scaling of frequency measurements RTE, RTO, RTP in cycles/min
For some tests a vector network analyzer is required. The Scope Suite software just supports VNAs from R&S to be connected via LAN for automated measurements. Can I use also other VNAs and do the measurement manually?
HDMI 인터페이스를 통해 추가 모니터를 연결하면 터치 기능이 동작하지 않습니다. 어떻게 하면 터치 기능을 다시 사용할 수 있나요?
When I do RMS measurements and an offset is applied, the result changes. I could not see that effect on other scopes. What is wrong here?
Connection of R&S ScopeSuite to RTO/RTP fails
패시브 프로브와 액티브 프로브를 비교해 보았습니다. 액티브 프로브에서 더 많은 노이즈가 발생하는 것 같습니다. 그 이유는 무엇이고 노이즈를 줄이려면 어떻게 해야 합니까?
오실로스코프를 사용하여 메인 라인의 전압을 측정하고자 합니다.
I/Q 소프트웨어 인터페이스 옵션 K11에 대한 구성 및 데이터 쿼리의 SCPI 시퀀스.
RTE/RTO/RTP Windows를 시작할 때 사용자 ID와 비밀번호를 입력합니다. 자동 로그인 기능을 다시 사용하려면 어떻게 해야 하나요?
Volume Adjustment of the "BEEP"
Zoom 기능으로 직사각형 신호의 상승 엣지를 볼때 스크린샷처럼 실제가 아닌 링잉 효과를 보게 됩니다. 이유가 무엇입니까?
Connection of DUT and Link partner with test fixture RT-ZF2
FAQ - Decoding of SENT protocoll shows CRC errors
I have exported the waveform into a csv file. When I open the file in Excel, the values are completely wrong. How can I get correct values?
Is an FSPC license dongle (1310.0002.03) always needed to run the FS-K96 software?
오실로스코프 프로그래밍 예제.
R&S Scope Suite - Error communicating with oscilloscope
Number of harmonics, RTE, RTO, Power option, FAQ