52 결과
Remote Desktop screen size of ZNB/ZND
한 개 채널에 마커가 있는 트레이스가 여러 개 있습니다. 마커 1의 결과를 쿼리하면 언제나 트레이스 1의 응답이 나옵니다. 트레이스 2에 대한 마커 1의 결과를 얻으려면 어떻게 하나요?
ZNA, ZNB, ZND - 스윕 완료 후 출력 종료 여부
Calibrating a vector network analyzer (VNA) with different connectors on each port
Export complex data of a trace with mathematics and time gating.
Restore the Auto Logon Configuration
How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?
Reverse sweep / backward sweep
scpi 명령어를 사용하여 트레이스 값의 쿼리를 실행하는데, y값만 도출됩니다. x값(주파수)도 얻을 방법이 있나요?
Store several diagrams in one file and each diagram on its own page
ZNA/ZNB: Export all mixed mode S-Parameters
I would like to use the ZNB as a signal generator. 포트 1과 포트 3에 주파수가 서로 다른 CW 신호가 필요합니다. 이러한 신호를 어떻게 얻을 수 있습니까?
채널 활성화를 확인하기 위해 “CONT:AUX:C x” 명령을 사용하고 있습니다. 그런데 AUX 커넥터에서 개별 핀이 "High"로 전환되지 않습니다.
ZNB - print to file command does not work anymore
ZNB - 스윕 위치 표시 아이콘을 비활성화하는 방법
SCPI remote error message on the display
ZNB/ZND/ZVA에서 75 Ohms로 calibration을 수행하고 싶습니다. 이 벡터 네트워크 분석기에서 75 Ohms의 ZV-Z53 자동 calibration unit을 사용할 수 있습니까?
원격 데스크톱으로 연결하여 ZNB를 사용할 때 하드키를 사용할 수 있는 방법이 있습니까?기기 왼쪽 하단에 표준 메뉴만 표시되고 "master keyboard"를 사용할 수 없습니다
ZNB: Power off at sweep end possible?
Remote Desktop connection
이전에 ZVA와 함께 TRL 교정 키트를 사용한 적이 있습니다. 이제 ZNB와 함께 교정 키트를 사용하려고 합니다. 그런데 ZNB로 교정 키트 데이터를 불러오기할 때마다 위와 같은 에러 메시지가 나타납니다.
Can the option ZNB-B10 be installed in the field?
스크린과 인쇄된 그래프를 동일하게 만들려면 어떻게 해야 합니까?
PC에서 원격 데스크톱을 사용해 신호분석기를 제어하려고 합니다. 신호분석기가 반응하지 않습니다.
이미 사용 중인 리미트 라인이 있습니다. 여기에 수직 오프셋을 적용할 수 있습니까?
장치에 파일이 있습니다. PC로 간단하게 파일을 옮기는 방법은 무엇인가요?
Improve the calibration procedure for different setups
I got a calibration kit with a sliding match standard. But there are no correction values for the NWA supplied.
I need to activate the deembedding function on a specific port. The data is available on a touchstone file (s2p) How can I load the file with remote commands?
Calibration 완료 후 자동 Calibration 키트로 Calibration 내용을 검증하려는데 검증에 계속 실패합니다. 무엇이 잘못된 건가요?
특정 채널의 트레이스를 하나의 파일(예: CSV)로 내보내려면 어떻게 해야 하나요?
License Keycode for VNAMUC is not accepted
벡터 네트워크 분석기(VNA)에서 컨트롤러 PC 또는 네트워크 드라이브로 결과를 전송하려고 합니다.
자동 교정 장치로 교정을 시작하면 다음과 같은 오류 메시지가 표시됩니다. 이는 무엇을 의미합니까?
External generator connected via USB not correctly recognized
활성 교정 키트 또는 교정 유닛에 선택한 교정 절차에 필요한 모든 표준이 포함되지 않았습니다(Active cal kit or cal unit does not contain all standards needed for selected cal procedure).
ZNB - several channels with external trigger
Bias tee limits and calibration considerations
VNA - 교정에 슬라이딩 매치가 꼭 필요한가요?
I perform a calibration with remote commands. With the command to start the calibration sweep with a short standard I get this error message. What is the problem?
Is it possible to automatically restart a ZNB with return of the AC power?
Save/recall files: own folder in 'Look In'
The MINUS key on the keypad does not work.
Remote control autocalibration with a calibration unit
When I export the time domain trace the stimulus values are in Hz, but not in seconds as shown on the screen. How can I get the export in time or distance?
모든 트레이스 데이터 쿼리를 한 번에 실행하는 방법이 있나요?
TRL calibration - middle of line or end of line
Calibration of two channels simultaneously with remote commands
How do I use the driver correctly?
ZNB, ASCII export of displayed trace values
Installing a USB-GPIB adapter
ZNB/ZND - 교정 유닛 특성분석에 잘못된 커넥터 유형이 표시됨