What is the correct pin layout of the DC inputs on the network analyzer's rear panel?

I have set my VNA to single sweep mode and switched on averaging with a factor of 10. But when I restart the single sweep, it stops after 1 sweep and the averaging is not done.

Provides the information required to prepare the instrument for use and start working.

This application note describes how to configure a Rohde & Schwarz Network Analyzer to make spectral measurements directly on a device under test.

16-Mar-2012 | AN-No. 1EZ62

I trigger this single sweep with the RSZVB_Send_Trigger_and_Wait_for_OPC driver, but this driver does not wait for the complete 10 sweeps. If I don't use averaging, this program is works.

How can I switch from remote to local state via remote control?

Provides basic information on the calibration kits R&S ZV-Z129, ZV-Z135 and ZV-Z170.

This application note describes the techniques to measure the dielectric properties of materials using a vector network analyzer. It also shows methods for converting the s-parameters to dielectric properties.

23-May-2012 | AN-No. RAC-0607-0019

Provides basic information on the calibration kits R&S®ZV-WR02, R&S®ZV-WR03, and R&S®ZV-WR05.

I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?

Provides basic information on the calibration kits R&S®ZN-Z170, ZN-Z135, ZN-Z129 and ZN-Z129E.

Provides basic information on the calibration kits R&S®ZV-WR06, ZV-WR08, ZV-WR10, ZV-WR12, ZV-WR15.

This paper shows how to perform a n-port multi-port calibration by using calibration unit with a lower number of ports than available of the vector network analyzer.

06-Feb-2013 | AN-No. 1EZ70

R&S®ZVA/B/T Instrument Security Procedures describes the types of memory and their usage in the R&S®ZVA/B/T and issues when working in secured environments.

R&S®ZVA Vector Network Analyzer - Product Brochure

Rohde & Schwarz Drivers under VEE - Installation and Troubleshooting

20-Dec-2012 | AN-No. 1MA035

This application note aims to explain test procedures and characterization of the relevant parameters for active phased array antennas.

04-Jul-2016 | AN-No. 1MA248

Welcome to this introductory video show about the R&S ZVA family of network analyzers.

13-Feb-2014 | AN-No. 1MA50

R&S®Forum for Instrument Remote Control

28-Jun-2018 | AN-No. 1MA196

RPG ZRXxxx Millimeterwave Receiver - Specifications

R&S®VISA is a standardized software library that allows fast communications over diverse interfaces with a wide variety of T&M instruments that are detected on the network from PC applications.

26-May-2020 | AN-No. 1DC02

R&S ZN-ZM292 Calibration Mixer - Specifications

Rohde & Schwarz Health Guide – For vector network analyzers - Flyer

Hints and Tricks for Remote Control of Spectrum and Network Analyzers

19-Aug-2014 | AN-No. 1EF62

R&S®ZV-Z9x, ZV-Z19x Test Port Cables - Specifications

This white paper provides an overview of test solutions addressing current and future requirements for antenna verification.

11-Nov-2016 | AN-No. 1MA286

R&S ZV-ZCAN Calibration Kit

R&S ZV-ZCAN Calibration Kit - Product Brochure

R&S®ZV-Z5x Calibration Unit - Specifications

Introduction to Attribute Based Instrument Drivers

01-Dec-2012 | AN-No. 1MA170