Sending a remote Control Command internally

What is the correct pin layout of the DC inputs on the network analyzer's rear panel?

R&S®ZVAX24 Quick Start Guide

I have set my VNA to single sweep mode and switched on averaging with a factor of 10. But when I restart the single sweep, it stops after 1 sweep and the averaging is not done.

Rohde & Schwarz Getting Started for the R&S ZCxxx frequency converters

This application note describes how to configure a Rohde & Schwarz Network Analyzer to make spectral measurements directly on a device under test.

16-Mar-2012 | AN-No. 1EZ62

TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines

I have used my TRL calibration kit with my ZVA before. Now I want to use also with my ZNB. But when I try to load the data of the calibration kit into the ZNB, the above error message is shown.

I trigger this single sweep with the RSZVB_Send_Trigger_and_Wait_for_OPC driver, but this driver does not wait for the complete 10 sweeps. If I don't use averaging, this program is works.

How can I switch from remote to local state via remote control?

I query the values of a trace using scpi commands. But I get the y-values only. Is there a possibility to get the y-values also (frequency)?

R&S ZV-WR02/WR03/-WR05 Technical Information

TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

TDR, TDT, ZVA vector network analyzer, This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

The R&S®ZVA vector network analyzer in combination with the R&S®ZVAB-K30 noise figure measurement option simplifies noise figure measurement, a key parameter for receiver performance evaluation.

TDR, TDT, ZVA vector network analyzer This video series demonstrates the calibration of a four-port network analyzer and the measurement of rise time, impedance vs. distance and skew on a board with differential lines.

How do I calculate these frequency points when I have a logarithmic sweep and know the center frequency, the span and the number of sweep points?

R&S ZV-WR06/-WR08/-WR10/-WR12/-WR15 Technical Information

Rohde & Schwarz Technical Information for the R&S ZV-Z129/-Z135/-Z170 calibration kits.

This application note describes the techniques to measure the dielectric properties of materials using a vector network analyzer. It also shows methods for converting the s-parameters to dielectric properties.

23-May-2012 | AN-No. RAC-0607-0019

ZVA Vector Network Analyzers, PIM, Rohde & Schwarz demonstrated fast and accurate passive intermodulation (PIM) testing of duplex filters at the European Microwave Week 2013 in Nuremberg.

Listing of all video overview pages sorted by categories and themes. Looking for additional insight on a specific application or measurement technique? Pick your topic of interest.

Rohde & Schwarz Technical Information for the R&S ZN-Z170/-Z135/-Z129/-Z129E calibration kits.

I want to use Port 1 and Port 3, so I tried to switch them on by setting the value to 1 (the default value) and to switch off Port 2 and Port 4 by setting the value to 0. But this does not work. How do I set the ports?

This paper shows how to perform a n-port multi-port calibration by using calibration unit with a lower number of ports than available of the vector network analyzer.

06-Feb-2013 | AN-No. 1EZ70

This document describes how a Windows®-based R&S® T&M instrument is remotely operated by an Android™ tablet as if working on it locally.

22-Aug-2013 | AN-No. 1MA236

Russian version - Измерения в диапазоне миллиметровых волн с использованием преобразователей семейства R&S®ZVA

Russian version - Измерение S22 усилителя в «горячем» режиме с импульсными сигналами на анализаторе цепей R&S®ZVA

This application note explains how to generate phase coherent signals with a compact easy-to-use solution.

07-Sep-2016 | AN-No. 1GP108

Bring your IEEE 802.11ad/ay products to market more quickly and reliably with comprehensive test and measurement solutions. Read more to be ahead.